Nortel-Magellan-Passport-DataCollectionMIB
DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE
FROM RFC-1212
components,
passportMIBs
FROM Nortel-Magellan-Passport-UsefulDefinitionsMIB
Counter32,
DisplayString,
StorageType,
RowStatus,
Gauge32,
Integer32,
Unsigned32
FROM Nortel-Magellan-Passport-StandardTextualConventionsMIB
AsciiString,
NonReplicated,
EnterpriseDateAndTime
FROM Nortel-Magellan-Passport-TextualConventionsMIB;
dataCollectionMIB OBJECT IDENTIFIER ::= { passportMIBs 14 }
col OBJECT IDENTIFIER ::= { components 21 }
colRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entry controls the addition and deletion of
col components."
::= { col 1 }
colRowStatusEntry OBJECT-TYPE
SYNTAX ColRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
col component."
INDEX {
colIndex }
::= { colRowStatusTable 1 }
ColRowStatusEntry ::= SEQUENCE {
colRowStatus
RowStatus,
colComponentName
DisplayString,
colStorageType
StorageType,
colIndex
INTEGER }
colRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
col components.
These components can be added."
::= { colRowStatusEntry 1 }
colComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { colRowStatusEntry 2 }
colStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
col tables."
::= { colRowStatusEntry 4 }
colIndex OBJECT-TYPE
SYNTAX INTEGER {
accounting(0),
alarm(1),
log(2),
debug(3),
scn(4),
trap(5),
stats(6) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the col tables."
::= { colRowStatusEntry 10 }
colProvTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColProvEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group specifies all of the provisioning data for a DCS
Collector."
::= { col 10 }
colProvEntry OBJECT-TYPE
SYNTAX ColProvEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colProvTable."
INDEX {
colIndex }
::= { colProvTable 1 }
ColProvEntry ::= SEQUENCE {
colAgentQueueSize
Unsigned32 }
colAgentQueueSize OBJECT-TYPE
SYNTAX Unsigned32 (0 | 20..10000)
ACCESS read-write
STATUS obsolete
DESCRIPTION
"This attribute has been replaced with the agentQueueSize attribute
in the Lp Engineering DataStream Ov component.
Upon migration, if the existing provisioned value of this attribute is
the same as the system default for this type of data, no new
components are added because the default is what the DataStream
component already would be using. Otherwise, if the value is not
the same as the system default, then for each Lp which is
provisioned at the time of the migration, a DataStream is
provisioned and the Ov's agentQueueSize is set to the non-default
value."
::= { colProvEntry 1 }
colStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group specifies the statistics operational attributes of the DCS
Collector, Agent and Spooler components."
::= { col 11 }
colStatsEntry OBJECT-TYPE
SYNTAX ColStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colStatsTable."
INDEX {
colIndex }
::= { colStatsTable 1 }
ColStatsEntry ::= SEQUENCE {
colCurrentQueueSize
Gauge32,
colRecordsRx
Counter32,
colRecordsDiscarded
Counter32 }
colCurrentQueueSize OBJECT-TYPE
SYNTAX Gauge32 (0..4294967295)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This gauge contains the current number of records held by this DCS
component."
::= { colStatsEntry 1 }
colRecordsRx OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This counter contains the cumulative number of records received by
a DCS component, from applications which send data to it, since
the processor last restarted.
This counter wraps to 0 when the maximum value is exceeded."
::= { colStatsEntry 2 }
colRecordsDiscarded OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the cumulative number of records discarded by this DCS
component since the processor last restarted.
This counter wraps to 0 when the maximum value is exceeded."
::= { colStatsEntry 3 }
colTimesTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColTimesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute specifies the scheduled times at which data should be
collected. Only accounting applications need the capability to
generate data in this way. Setting this attribute for other streams has
no effect.
The user can enter the times in any order and duplicates are
prevented at data entry. There is a limit of 24 entries, which is
imposed at semantic check time. The collection times are triggered
in chronological order. A semantic check error is issued if any 2
entries are less than 1 hour apart or if any 2 entries are more than 12
hours apart (which implies that if any entries are provided, there
must be at least 2 entries).
Note that by default (that is, in the absence of a provisioned
schedule), a Virtual Circuit (VC) starts its own 12-hour accounting
timer. If any collection times are provisioned here, then the Time-
Of-Day-Accounting (TODA) method is used in place of 12-hour
accounting. This is applicable to both Switched VCs and Permanent
VCs."
::= { col 266 }
colTimesEntry OBJECT-TYPE
SYNTAX ColTimesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colTimesTable."
INDEX {
colIndex,
colTimesValue }
::= { colTimesTable 1 }
ColTimesEntry ::= SEQUENCE {
colTimesValue
EnterpriseDateAndTime,
colTimesRowStatus
RowStatus }
colTimesValue OBJECT-TYPE
SYNTAX EnterpriseDateAndTime (SIZE (5))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This variable represents both the value and the index for the
colTimesTable."
::= { colTimesEntry 1 }
colTimesRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS write-only
STATUS mandatory
DESCRIPTION
"This variable is used to control the addition and deletion
of individual values of the colTimesTable."
::= { colTimesEntry 2 }
colLastTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColLastEntry
ACCESS not-accessible
STATUS obsolete
DESCRIPTION
"Note: This was made obsolete in R4.1 (BD0108A).
This attribute is used for Collector/stats and Collector/account.
For statistics, when collection is turned off, or prior to the very first
probe, the value is the empty list. Otherwise, this is the network
time at which the last probe was sent out (that is, the last time that
statistics were collected from, or at least reset by, the applications
providing them).
For accounting, when no entries exist in collectionTimes, or prior to
the very first collection time, the value is the empty list. Otherwise,
this is the network time at which the last time-of-day changeover
occurred."
::= { col 275 }
colLastEntry OBJECT-TYPE
SYNTAX ColLastEntry
ACCESS not-accessible
STATUS obsolete
DESCRIPTION
"An entry in the colLastTable."
INDEX {
colIndex,
colLastValue }
::= { colLastTable 1 }
ColLastEntry ::= SEQUENCE {
colLastValue
EnterpriseDateAndTime }
colLastValue OBJECT-TYPE
SYNTAX EnterpriseDateAndTime (SIZE (19))
ACCESS read-only
STATUS obsolete
DESCRIPTION
"This variable represents both the value and the index for the
colLastTable."
::= { colLastEntry 1 }
colPeakTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColPeakEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute specifies the length of the accounting peak water mark
interval. It is at least one minute and at most 15 minutes long. An
accounting peak water mark within a given accounting interval is
the accounting count which occured during a peak water mark
interval with the highest traffic. Peak water marks are used to
determine traffic bursts. If no value is provisioned for this attribute
value of 5 minutes is assumed. Peak water mark is only measured if
attribute collectionTimes in Collector/account is provisioned."
::= { col 279 }
colPeakEntry OBJECT-TYPE
SYNTAX ColPeakEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colPeakTable."
INDEX {
colIndex,
colPeakValue }
::= { colPeakTable 1 }
ColPeakEntry ::= SEQUENCE {
colPeakValue
Integer32,
colPeakRowStatus
RowStatus }
colPeakValue OBJECT-TYPE
SYNTAX Integer32 (1..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This variable represents both the value and the index for the
colPeakTable."
::= { colPeakEntry 1 }
colPeakRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS write-only
STATUS mandatory
DESCRIPTION
"This variable is used to control the addition and deletion
of individual values of the colPeakTable."
::= { colPeakEntry 2 }
colSp OBJECT IDENTIFIER ::= { col 2 }
colSpRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColSpRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entry controls the addition and deletion of
colSp components."
::= { colSp 1 }
colSpRowStatusEntry OBJECT-TYPE
SYNTAX ColSpRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
colSp component."
INDEX {
colIndex,
colSpIndex }
::= { colSpRowStatusTable 1 }
ColSpRowStatusEntry ::= SEQUENCE {
colSpRowStatus
RowStatus,
colSpComponentName
DisplayString,
colSpStorageType
StorageType,
colSpIndex
NonReplicated }
colSpRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
colSp components.
These components cannot be added nor deleted."
::= { colSpRowStatusEntry 1 }
colSpComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { colSpRowStatusEntry 2 }
colSpStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
colSp tables."
::= { colSpRowStatusEntry 4 }
colSpIndex OBJECT-TYPE
SYNTAX NonReplicated
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the colSp tables."
::= { colSpRowStatusEntry 10 }
colSpProvTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColSpProvEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group specifies all of the provisioning data for a DCS Spooler."
::= { colSp 10 }
colSpProvEntry OBJECT-TYPE
SYNTAX ColSpProvEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colSpProvTable."
INDEX {
colIndex,
colSpIndex }
::= { colSpProvTable 1 }
ColSpProvEntry ::= SEQUENCE {
colSpSpooling
INTEGER,
colSpMaximumNumberOfFiles
Unsigned32 }
colSpSpooling OBJECT-TYPE
SYNTAX INTEGER {
off(0),
on(1) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies whether or not this type of data is spooled to
the disk. If set to off, it is roughly equivalent to Locking the Spooler
(except this will survive processor restarts).
The following defaults are used:
- alarm: on
- accounting: on
- log: on
- debug: off
- scn: on
- trap: off (see Note below)
- stats: on
Note that SNMP Traps cannot be spooled. A semantic check
prevents the user from setting the value to on for the trap stream."
::= { colSpProvEntry 1 }
colSpMaximumNumberOfFiles OBJECT-TYPE
SYNTAX Unsigned32 (0..200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies the maximum number of files that should be
kept on the disk in the directory containing the closed files of this
type. The value 0 is defined to mean 'unlimited'.
A different default for each type of Spooler is defined as follows:
- alarm: 30
- accounting: 200
- debug: 2
- log: 10
- scn: 10
- trap: 2 (this value is meaningless and is ignored)
- stats: 200"
::= { colSpProvEntry 2 }
colSpStateTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColSpStateEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group contains the three OSI State attributes and the six OSI
Status attributes. The descriptions generically indicate what each
attribute implies about the component. Note that not all the values
and state combinations described here are supported by every
component which uses this group. For component-specific
information and the valid state combinations, refer to NTP 241-
7001-150, Passport Operations and Maintenance Guide."
::= { colSp 11 }
colSpStateEntry OBJECT-TYPE
SYNTAX ColSpStateEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colSpStateTable."
INDEX {
colIndex,
colSpIndex }
::= { colSpStateTable 1 }
ColSpStateEntry ::= SEQUENCE {
colSpAdminState
INTEGER,
colSpOperationalState
INTEGER,
colSpUsageState
INTEGER,
colSpAvailabilityStatus
OCTET STRING,
colSpProceduralStatus
OCTET STRING,
colSpControlStatus
OCTET STRING,
colSpAlarmStatus
OCTET STRING,
colSpStandbyStatus
INTEGER,
colSpUnknownStatus
INTEGER }
colSpAdminState OBJECT-TYPE
SYNTAX INTEGER {
locked(0),
unlocked(1),
shuttingDown(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component."
DEFVAL { unlocked }
::= { colSpStateEntry 1 }
colSpOperationalState OBJECT-TYPE
SYNTAX INTEGER {
disabled(0),
enabled(1) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component."
DEFVAL { disabled }
::= { colSpStateEntry 2 }
colSpUsageState OBJECT-TYPE
SYNTAX INTEGER {
idle(0),
active(1),
busy(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component."
DEFVAL { idle }
::= { colSpStateEntry 3 }
colSpAvailabilityStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)"
::= { colSpStateEntry 4 }
colSpProceduralStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)"
::= { colSpStateEntry 5 }
colSpControlStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)"
::= { colSpStateEntry 6 }
colSpAlarmStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)"
::= { colSpStateEntry 7 }
colSpStandbyStatus OBJECT-TYPE
SYNTAX INTEGER {
hotStandby(0),
coldStandby(1),
providingService(2),
notSet(15) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource."
DEFVAL { notSet }
::= { colSpStateEntry 8 }
colSpUnknownStatus OBJECT-TYPE
SYNTAX INTEGER {
false(0),
true(1) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure."
DEFVAL { false }
::= { colSpStateEntry 9 }
colSpOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColSpOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group contains the operational attributes specific to a DCS
Spooler."
::= { colSp 12 }
colSpOperEntry OBJECT-TYPE
SYNTAX ColSpOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colSpOperTable."
INDEX {
colIndex,
colSpIndex }
::= { colSpOperTable 1 }
ColSpOperEntry ::= SEQUENCE {
colSpSpoolingFileName
AsciiString }
colSpSpoolingFileName OBJECT-TYPE
SYNTAX AsciiString (SIZE (0..128))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"When spooling is on, this attribute contains the name of the open
file into which data is currently being spooled. When spooling is
off, the value of this attribute is the empty string."
::= { colSpOperEntry 1 }
colSpStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColSpStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group specifies the statistics operational attributes of the DCS
Collector, Agent and Spooler components."
::= { colSp 13 }
colSpStatsEntry OBJECT-TYPE
SYNTAX ColSpStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colSpStatsTable."
INDEX {
colIndex,
colSpIndex }
::= { colSpStatsTable 1 }
ColSpStatsEntry ::= SEQUENCE {
colSpCurrentQueueSize
Gauge32,
colSpRecordsRx
Counter32,
colSpRecordsDiscarded
Counter32 }
colSpCurrentQueueSize OBJECT-TYPE
SYNTAX Gauge32 (0..4294967295)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This gauge contains the current number of records held by this DCS
component."
::= { colSpStatsEntry 1 }
colSpRecordsRx OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This counter contains the cumulative number of records received by
a DCS component, from applications which send data to it, since
the processor last restarted.
This counter wraps to 0 when the maximum value is exceeded."
::= { colSpStatsEntry 2 }
colSpRecordsDiscarded OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the cumulative number of records discarded by this DCS
component since the processor last restarted.
This counter wraps to 0 when the maximum value is exceeded."
::= { colSpStatsEntry 3 }
colAg OBJECT IDENTIFIER ::= { col 3 }
colAgRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColAgRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"*** THIS TABLE CURRENTLY NOT IMPLEMENTED ***
This entry controls the addition and deletion of
colAg components."
::= { colAg 1 }
colAgRowStatusEntry OBJECT-TYPE
SYNTAX ColAgRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
colAg component."
INDEX {
colIndex,
colAgIndex }
::= { colAgRowStatusTable 1 }
ColAgRowStatusEntry ::= SEQUENCE {
colAgRowStatus
RowStatus,
colAgComponentName
DisplayString,
colAgStorageType
StorageType,
colAgIndex
Integer32 }
colAgRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
colAg components.
These components cannot be added nor deleted."
::= { colAgRowStatusEntry 1 }
colAgComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { colAgRowStatusEntry 2 }
colAgStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
colAg tables."
::= { colAgRowStatusEntry 4 }
colAgIndex OBJECT-TYPE
SYNTAX Integer32 (0..15)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the colAg tables."
::= { colAgRowStatusEntry 10 }
colAgStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColAgStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"*** THIS TABLE CURRENTLY NOT IMPLEMENTED ***
This group specifies the statistics operational attributes of the DCS
Collector, Agent and Spooler components."
::= { colAg 10 }
colAgStatsEntry OBJECT-TYPE
SYNTAX ColAgStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colAgStatsTable."
INDEX {
colIndex,
colAgIndex }
::= { colAgStatsTable 1 }
ColAgStatsEntry ::= SEQUENCE {
colAgCurrentQueueSize
Gauge32,
colAgRecordsRx
Counter32,
colAgRecordsDiscarded
Counter32 }
colAgCurrentQueueSize OBJECT-TYPE
SYNTAX Gauge32 (0..4294967295)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This gauge contains the current number of records held by this DCS
component."
::= { colAgStatsEntry 1 }
colAgRecordsRx OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This counter contains the cumulative number of records received by
a DCS component, from applications which send data to it, since
the processor last restarted.
This counter wraps to 0 when the maximum value is exceeded."
::= { colAgStatsEntry 2 }
colAgRecordsDiscarded OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the cumulative number of records discarded by this DCS
component since the processor last restarted.
This counter wraps to 0 when the maximum value is exceeded."
::= { colAgStatsEntry 3 }
colAgAgentStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF ColAgAgentStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"*** THIS TABLE CURRENTLY NOT IMPLEMENTED ***
This group contains the statistical attributes specific to the DCS
Agent components."
::= { colAg 11 }
colAgAgentStatsEntry OBJECT-TYPE
SYNTAX ColAgAgentStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the colAgAgentStatsTable."
INDEX {
colIndex,
colAgIndex }
::= { colAgAgentStatsTable 1 }
ColAgAgentStatsEntry ::= SEQUENCE {
colAgRecordsNotGenerated
Counter32 }
colAgRecordsNotGenerated OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the records of a particular event type on this
Card which could not be generated by some application due to
some problem such as insufficient resources. One cannot tell exactly
which event could not be generated, nor which application instance
tried to generate it, but when this count increases, it is an indicator
that some re-engineering may be required and will provide some
idea as to why a record is missing.
This counter wraps to 0 when the maximum value is exceeded."
::= { colAgAgentStatsEntry 1 }
dataCollectionGroup OBJECT IDENTIFIER ::= { dataCollectionMIB 1 }
dataCollectionGroupBE OBJECT IDENTIFIER ::= { dataCollectionGroup 5 }
dataCollectionGroupBE00 OBJECT IDENTIFIER ::= { dataCollectionGroupBE 1 }
dataCollectionGroupBE00A OBJECT IDENTIFIER ::= { dataCollectionGroupBE00 2 }
dataCollectionCapabilities OBJECT IDENTIFIER ::= { dataCollectionMIB 3 }
dataCollectionCapabilitiesBE OBJECT IDENTIFIER ::= { dataCollectionCapabilities 5 }
dataCollectionCapabilitiesBE00 OBJECT IDENTIFIER ::= { dataCollectionCapabilitiesBE 1 }
dataCollectionCapabilitiesBE00A OBJECT IDENTIFIER ::= { dataCollectionCapabilitiesBE00 2 }
END