Nortel-Magellan-Passport-TrunksMIB
DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE
FROM RFC-1212
components,
passportMIBs
FROM Nortel-Magellan-Passport-UsefulDefinitionsMIB
Counter32,
DisplayString,
StorageType,
RowStatus,
PassportCounter64,
InterfaceIndex,
Gauge32,
Integer32,
Unsigned32
FROM Nortel-Magellan-Passport-StandardTextualConventionsMIB
AsciiString,
NonReplicated,
FixedPoint1
FROM Nortel-Magellan-Passport-TextualConventionsMIB;
trunksMIB OBJECT IDENTIFIER ::= { passportMIBs 43 }
trk OBJECT IDENTIFIER ::= { components 60 }
trkRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entry controls the addition and deletion of
trk components."
::= { trk 1 }
trkRowStatusEntry OBJECT-TYPE
SYNTAX TrkRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
trk component."
INDEX {
trkIndex }
::= { trkRowStatusTable 1 }
TrkRowStatusEntry ::= SEQUENCE {
trkRowStatus
RowStatus,
trkComponentName
DisplayString,
trkStorageType
StorageType,
trkIndex
Integer32 }
trkRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
trk components.
These components can be added and deleted."
::= { trkRowStatusEntry 1 }
trkComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { trkRowStatusEntry 2 }
trkStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
trk tables."
::= { trkRowStatusEntry 4 }
trkIndex OBJECT-TYPE
SYNTAX Integer32 (0..65535)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the trk tables."
::= { trkRowStatusEntry 10 }
trkIfEntryTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkIfEntryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group contains the provisionable attributes for the ifEntry."
::= { trk 100 }
trkIfEntryEntry OBJECT-TYPE
SYNTAX TrkIfEntryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkIfEntryTable."
INDEX {
trkIndex }
::= { trkIfEntryTable 1 }
TrkIfEntryEntry ::= SEQUENCE {
trkIfAdminStatus
INTEGER,
trkIfIndex
InterfaceIndex }
trkIfAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
testing(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The desired state of the interface. The up state indicates the
interface is operational. The down state indicates the interface is not
operational. The testing state indicates that no operational packets
can be passed."
DEFVAL { up }
::= { trkIfEntryEntry 1 }
trkIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the index for the IfEntry. Its value is automatically initialized
during the provisioning process."
::= { trkIfEntryEntry 2 }
trkProvTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkProvEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group of attributes provides the parameters used by the layer 3
Trunk to Trunk staging protocol."
::= { trk 101 }
trkProvEntry OBJECT-TYPE
SYNTAX TrkProvEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkProvTable."
INDEX {
trkIndex }
::= { trkProvTable 1 }
TrkProvEntry ::= SEQUENCE {
trkExpectedRemoteNodeName
AsciiString,
trkRemoteValidationAction
INTEGER,
trkMaximumExpectedRoundTripDelay
Unsigned32,
trkIdleTimeOut
Unsigned32 }
trkExpectedRemoteNodeName OBJECT-TYPE
SYNTAX AsciiString (SIZE (0..12))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies the expected node name of the module to
which this Trunk is connected. Once entered, the node name must
correspond to the Mod nodeName attribute of the remote node. The
Trunk end points exchange their node name through the Trunk
staging protocol. The staged value is validated and the
remoteValidationAction will be executed for those values not
matching the value supplied for this attribute.
If this attribute is an empty string, then the comparison is always
successful."
::= { trkProvEntry 1 }
trkRemoteValidationAction OBJECT-TYPE
SYNTAX INTEGER {
continue(0),
disable(1) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies the action to be taken if there is a mismatch
between the expectedRemoteNodeName attribute and the value
received from the remote end. The remoteValidationAction
determines the action when a value is supplied to the
expectedRemoteNodeName attribute. If this attribute is provisioned
to continue then upon an unsuccessful validation staging continues,
otherwise, if disable is set then the Trunk does not continue to stage
but, attempts to stage again after a one minute time out.
All unsuccessful validation when the expectedRemoteNodeName
has been set result in the generation of an alarm."
DEFVAL { continue }
::= { trkProvEntry 2 }
trkMaximumExpectedRoundTripDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..1500)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This is the maximum round trip delay value used by the Trunk
staging protocol, in conjunction with measuredSpeedToIf, to
determine if it has taken too long to successfully stage with a
remote Trunk. The value specified must be larger than the
measuredRoundTripDelay or the Trunk may not successfully stage."
DEFVAL { 1500 }
::= { trkProvEntry 3 }
trkIdleTimeOut OBJECT-TYPE
SYNTAX Unsigned32 (2..30)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies the Trunk protocol idle time out duration in
units of seconds. If the local Trunk does not receive any packets
from the link for the period specified by this attribute, the Trunk
enters Are You There (AYT) mode for up to two seconds. If the
Trunk does not receive any packets from the remote during the AYT
mode it will restage; otherwise, it exits AYT mode and continues to
provide service."
DEFVAL { 4 }
::= { trkProvEntry 4 }
trkOverridesTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkOverridesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Theses attribute comprise the set of provisionable override
parameters supported by both the Trunk and DpnGateway
components. The attributes are used when reporting operational
attributes (used for metric calculations) to the routing system."
::= { trk 102 }
trkOverridesEntry OBJECT-TYPE
SYNTAX TrkOverridesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkOverridesTable."
INDEX {
trkIndex }
::= { trkOverridesTable 1 }
TrkOverridesEntry ::= SEQUENCE {
trkOverrideTransmitSpeed
Gauge32,
trkOldOverrideRoundTripDelay
Gauge32,
trkOverrideRoundTripUsec
FixedPoint1 }
trkOverrideTransmitSpeed OBJECT-TYPE
SYNTAX Gauge32 (0 | 1000..4294967295)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This is the overridden value of link speed (bit/s) that, if staged
successfully with the remote, is reported to the routing system for
metric calculations. A zero indicates that an override value has not
been provided and that only the measured value will be reported to
the routing system.
If this value is changed on a Trunk or DpnGateway that is enabled,
the LOCK and UNLOCK commands must be issued to the
component to restage the override with the remote."
DEFVAL { 0 }
::= { trkOverridesEntry 1 }
trkOldOverrideRoundTripDelay OBJECT-TYPE
SYNTAX Gauge32 (0..1500)
ACCESS read-write
STATUS obsolete
DESCRIPTION
"This is the overridden value of link delay (ms) that, if staged
successfully with the remote, is reported to the routing system for
metric calculations. A zero indicates that an override value has not
been provided and that only the measured value will be reported to
the routing system.
If this value is changed on a Trunk or DpnGateway that is enabled,
the LOCK and UNLOCK commands must be issued to the
component to restage the override with the remote."
DEFVAL { 0 }
::= { trkOverridesEntry 2 }
trkOverrideRoundTripUsec OBJECT-TYPE
SYNTAX FixedPoint1 (0..15000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This is the overridden value of link delay (ms) that, if staged
successfully with the remote, is reported to the routing system for
metric calculations. A zero indicates that an override value has not
been provided and that only the measured value will be reported to
the routing system.
If this value is changed on a Trunk or DpnGateway that is enabled,
the LOCK and UNLOCK commands must be issued to the
component to restage the override with the remote."
DEFVAL { 0 }
::= { trkOverridesEntry 3 }
trkStateTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkStateEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group contains the three OSI State attributes and the six OSI
Status attributes. The descriptions generically indicate what each
attribute implies about the component. Note that not all the values
and state combinations described here are supported by every
component which uses this group. For component-specific
information and the valid state combinations, refer to NTP 241-
7001-150, Passport Operations and Maintenance Guide."
::= { trk 103 }
trkStateEntry OBJECT-TYPE
SYNTAX TrkStateEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkStateTable."
INDEX {
trkIndex }
::= { trkStateTable 1 }
TrkStateEntry ::= SEQUENCE {
trkAdminState
INTEGER,
trkOperationalState
INTEGER,
trkUsageState
INTEGER,
trkAvailabilityStatus
OCTET STRING,
trkProceduralStatus
OCTET STRING,
trkControlStatus
OCTET STRING,
trkAlarmStatus
OCTET STRING,
trkStandbyStatus
INTEGER,
trkUnknownStatus
INTEGER }
trkAdminState OBJECT-TYPE
SYNTAX INTEGER {
locked(0),
unlocked(1),
shuttingDown(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component."
DEFVAL { unlocked }
::= { trkStateEntry 1 }
trkOperationalState OBJECT-TYPE
SYNTAX INTEGER {
disabled(0),
enabled(1) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component."
DEFVAL { disabled }
::= { trkStateEntry 2 }
trkUsageState OBJECT-TYPE
SYNTAX INTEGER {
idle(0),
active(1),
busy(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component."
DEFVAL { idle }
::= { trkStateEntry 3 }
trkAvailabilityStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)"
::= { trkStateEntry 4 }
trkProceduralStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)"
::= { trkStateEntry 5 }
trkControlStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)"
::= { trkStateEntry 6 }
trkAlarmStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)"
::= { trkStateEntry 7 }
trkStandbyStatus OBJECT-TYPE
SYNTAX INTEGER {
hotStandby(0),
coldStandby(1),
providingService(2),
notSet(15) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource."
DEFVAL { notSet }
::= { trkStateEntry 8 }
trkUnknownStatus OBJECT-TYPE
SYNTAX INTEGER {
false(0),
true(1) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure."
DEFVAL { false }
::= { trkStateEntry 9 }
trkOperStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkOperStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group includes the Operational Status attribute. This attribute
defines the current operational state of this component."
::= { trk 104 }
trkOperStatusEntry OBJECT-TYPE
SYNTAX TrkOperStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkOperStatusTable."
INDEX {
trkIndex }
::= { trkOperStatusTable 1 }
TrkOperStatusEntry ::= SEQUENCE {
trkSnmpOperStatus
INTEGER }
trkSnmpOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
testing(3) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current state of the interface. The up state indicates the
interface is operational and capable of forwarding packets. The
down state indicates the interface is not operational, thus unable to
forward packets. testing state indicates that no operational packets
can be passed."
DEFVAL { up }
::= { trkOperStatusEntry 1 }
trkOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This is the group of operational attributes supported by the Trunk."
::= { trk 105 }
trkOperEntry OBJECT-TYPE
SYNTAX TrkOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkOperTable."
INDEX {
trkIndex }
::= { trkOperTable 1 }
TrkOperEntry ::= SEQUENCE {
trkRemoteComponentName
AsciiString }
trkRemoteComponentName OBJECT-TYPE
SYNTAX AsciiString (SIZE (1..27))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute is the component name of the remote end which it has
supplied through the Trunk staging protocol."
::= { trkOperEntry 1 }
trkTransportTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkTransportEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group of attributes contains the set of operational parameters
measured and maintained by both the Trunk and DpnGateway
components."
::= { trk 106 }
trkTransportEntry OBJECT-TYPE
SYNTAX TrkTransportEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkTransportTable."
INDEX {
trkIndex }
::= { trkTransportTable 1 }
TrkTransportEntry ::= SEQUENCE {
trkMeasuredSpeedToIf
Gauge32,
trkMeasuredRoundTripDelay
Gauge32,
trkMaxTxUnit
Gauge32,
trkMeasuredRoundTripDelayUsec
FixedPoint1 }
trkMeasuredSpeedToIf OBJECT-TYPE
SYNTAX Gauge32 (0..4294967295)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the current 'transmittable' bandwidth of the
underlying facility.
For a Trunk with a Unack subcomponent, and a DpnGateway with a
Utp subcomponent, if a serial port is used, the value is the measured
transmit speed of the port; if a channelized port (E1/DS1) is used,
the value is the measured transmit speed of the Channel.
For a Trunk with an AtmAccess subcomponent, the value is
calculated by converting the VCC transmit cell rate to an equivalent
bit rate. The VCC transmit cell rate is determined based on the
vccReportingBw attribute of the Trunk AtmAccess component. If
vccReportingBw has a value of pcr and attribute bwElastic of
AtmAccess has a value of no, the peak cell rate (PCR) of the VCC,
defined in txTrafficDescParm of AtmIf Vcc Vcd, is used. If
vccReportingBw has a value of pcr and attribute bwElastic of
AtmAccess has a value of yes, the minimum of the PCR, defined in
txTrafficDescParm of AtmIf Vcc Vcd, and the current cell rate
(CCR) of the VCC is used. If vccReportingBw has a value of acr,
the best measurement of the actual cell rate (ACR) of the VCC is
used, which is the minimum of the PCR, the CCR and the actual
shaping rate (ASR).
For a DpnGateway with a FrAccess subcomponent, the value
indicates the committedInformationRate of FrAccess FrMuxSetup.
A value of zero is displayed when the underlying facility is disabled
or the current 'transmittable' bandwidth is unknown."
DEFVAL { 0 }
::= { trkTransportEntry 1 }
trkMeasuredRoundTripDelay OBJECT-TYPE
SYNTAX Gauge32 (0..1500)
ACCESS read-only
STATUS obsolete
DESCRIPTION
"This attribute indicates the measured Round Trip Delay (msec)
discovered with the remote through the Trunk and DpnGateway
staging protocols. The value includes emission, propagation, and
queuing delays. A 512 byte data packet is used to perform the
measurement. A value of zero is displayed when the link is disabled
or the measured Round Trip Delay is unknown."
DEFVAL { 0 }
::= { trkTransportEntry 2 }
trkMaxTxUnit OBJECT-TYPE
SYNTAX Gauge32 (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the maximum transmission unit (byte size) that is supported
by the Trunk or DpnGateway component. This size includes the
data and routing headers. A value of zero indicates the MTU has not
yet been determined."
DEFVAL { 0 }
::= { trkTransportEntry 3 }
trkMeasuredRoundTripDelayUsec OBJECT-TYPE
SYNTAX FixedPoint1 (0..15000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the measured Round Trip Delay (msec)
discovered with the remote through the Trunk and DpnGateway
staging protocols. The value includes emission, propagation, and
queuing delays. A 512 byte data packet is used to perform the
measurement. A value of zero is displayed when the link is disabled
or the measured Round Trip Delay is unknown."
DEFVAL { 0 }
::= { trkTransportEntry 4 }
trkStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"These attributes comprise the statistics collected by the Trunk
component."
::= { trk 107 }
trkStatsEntry OBJECT-TYPE
SYNTAX TrkStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkStatsTable."
INDEX {
trkIndex }
::= { trkStatsTable 1 }
TrkStatsEntry ::= SEQUENCE {
trkAreYouThereModeEntries
Counter32,
trkPktFromIf
PassportCounter64,
trkTrunkPktFromIf
Counter32,
trkTrunkPktToIf
Counter32,
trkDiscardUnforward
PassportCounter64,
trkDiscardTrunkPktFromIf
Counter32,
trkIntPktFromIf
PassportCounter64,
trkDiscardIntUnforward
PassportCounter64,
trkStagingAttempts
Counter32,
trkDiscardTrunkPktToIf
Counter32,
trkUtilization
Gauge32 }
trkAreYouThereModeEntries OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of times that the component has
entered Are You There mode. This counter wraps around to zero
when the maximum value is exceeded."
::= { trkStatsEntry 1 }
trkPktFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of packets received from the
remote module. It does not include the packets received from the
interrupting queue. This counter wraps around to zero when the
maximum value is exceeded."
::= { trkStatsEntry 2 }
trkTrunkPktFromIf OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of internal trunk protocol packets
(including those from the interrupting queue) received from the
remote module. These packets are forwarded to the Trunk
component. This counter wraps around to zero when the maximum
value is exceeded."
::= { trkStatsEntry 3 }
trkTrunkPktToIf OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of internal trunk protocol packets
(including those through the interrupting queue) transmitted to the
remote module. This counter wraps around to zero when the
maximum value is exceeded."
::= { trkStatsEntry 4 }
trkDiscardUnforward OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of packets received from the
remote module that have been discarded. It does not include the
packets received from the interrupting queue that have been
discarded. This counter wraps around to zero when the maximum
value is exceeded. Two main reasons that cause this counter to
increase are:
(1) the remote protocol is not compatible with the local protocol
stack or,
(2) the packet cannot be forwarded due to a recent loss of
connectivity or due to congestion."
::= { trkStatsEntry 5 }
trkDiscardTrunkPktFromIf OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of internal trunk protocol packets
(including those on the interrupting queue) received from the
remote module that have been discarded. This counter wraps around
to zero when the maximum value is exceeded. The three main
reasons that cause this counter to increase are:
(1) the two Trunks are not synchronized,
(2) the remote trunk protocol is not the same version as the local
protocol, and
(3) the remote trunk has restaged."
::= { trkStatsEntry 6 }
trkIntPktFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of packets received on the
interrupting queue from the remote module. This counter wraps
around to zero when the maximum value is exceeded."
::= { trkStatsEntry 7 }
trkDiscardIntUnforward OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of packets received on the
interrupting queue from the remote module that have been
discarded. This counter wraps around to zero when the maximum
value is exceeded. Two main reasons that cause this counter to
increment are:
(1) the remote protocol is not compatible to the local protocol stack
and,
(2) the packet cannot be forwarded due to either a recent loss of
connectivity or due to congestion."
::= { trkStatsEntry 8 }
trkStagingAttempts OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of times that the staging protocol
has attempted to stage with the remote module. This counter wraps
around to zero when the maximum value is exceeded. The main
reason that causes this counter to increment is that the local
hardware is up but, the local protocol cannot stage with the remote
protocol due to a faulty connection. If the value is zero, then the
local hardware has never enabled successfully."
::= { trkStatsEntry 9 }
trkDiscardTrunkPktToIf OBJECT-TYPE
SYNTAX Counter32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of internal trunk protocol packets
(including those through the interrupting queue) that have been
discarded before being transmitted to the remote module. This
counter wraps around to zero when the maximum value is
exceeded. The main reason that causes this counter to increment is
that the trunk can not get sufficient resources to create an internal
trunk protocol packet."
::= { trkStatsEntry 10 }
trkUtilization OBJECT-TYPE
SYNTAX Gauge32 (0..200)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute indicates the average trunk utilization.
For a Trunk/n with an Unack subcomponent, the value is the link
receive utilization. It is calculated every minute by comparing the
number of octets received from the remote module against the value
of the Trunk/n measuredSpeedToIf. Since the trunk application
solely owns the physical link, the maximum link utilization is
100%.
For a Trunk/n with an AtmAccess subcomponent, the value is the
VCC(s) transmit utilization. It is calculated every 30 seconds by
comparing the number of cells transmitted by AtmIf Vcc(s) against
the value of the Trunk/n measuredSpeedToIf. The VCCs include the
trunk VCC indicated by atmConnection of Trunk/n AtmAccess and
the PORS SPO (Short Path Oriented) multiplexing VCC if
applicable. The PORS SPO multiplexing VCC only applies to a
Trunk/n with subcomponents Pa AtmAccess, where the mode of
AtmAccess is multiplexing, and the AtmAccess is linked to a second
VCC indicated by atmConnection of Pa AtmAccess. Since the trunk
application shares a physical link with other applications, the VCCs
utilization can exceed 100%, and the value 200% is chosen as the
maximum calculated utilization."
::= { trkStatsEntry 11 }
trkSpeedReportingTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkSpeedReportingEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This group of provisionable attributes provides the ability to disable
or enable the generation of speed change alarms by the Trunk
component. It also provides the ability to disable or enable the
Dynamic Speed Reporting mechanism."
::= { trk 109 }
trkSpeedReportingEntry OBJECT-TYPE
SYNTAX TrkSpeedReportingEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkSpeedReportingTable."
INDEX {
trkIndex }
::= { trkSpeedReportingTable 1 }
TrkSpeedReportingEntry ::= SEQUENCE {
trkSpeedReportingHoldOff
Unsigned32,
trkLowSpeedAlarmThreshold
Unsigned32,
trkHighSpeedAlarmThreshold
Unsigned32 }
trkSpeedReportingHoldOff OBJECT-TYPE
SYNTAX Unsigned32 (1..1200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies the hold off time for reporting speed
increases. When the measuredSpeedToIf reaches a level specified
by the speedReportingThresholds attribute, the value specifies the
duration (in units of seconds) for which the measuredSpeedToIf
must maintain that level before it will be reported."
DEFVAL { 30 }
::= { trkSpeedReportingEntry 2 }
trkLowSpeedAlarmThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0 | 1..4294967295)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies the lower end of the range of normal speeds
for this Trunk. If the measuredSpeedToIf drops below this value the
Trunk component generates a SET alarm. When the
measuredSpeedToIf reaches or exceeds the value of this attribute,
the Trunk component will generate a CLEAR alarm."
DEFVAL { 0 }
::= { trkSpeedReportingEntry 3 }
trkHighSpeedAlarmThreshold OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This attribute specifies the upper end of the range of normal speeds
for this Trunk. If the measuredSpeedToIf exceeds this value the
Trunk component generates a SET alarm. When the
measuredSpeedToIf returns to or falls below the value of this
attribute, the Trunk component will generate a CLEAR alarm."
DEFVAL { 4294967295 }
::= { trkSpeedReportingEntry 4 }
trkSpdThTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkSpdThEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute controls the behavior of the Dynamic Speed
Reporting mechanism. If its value is empty then the mechanism is
disabled and neither increases nor decreases are reported.
Otherwise, the attribute may contain up to seven threshold levels
which are used to control the reporting of speed increases. Speed
decreases are always reported immediately. If the
measuredSpeedToIf increases such that it reaches one of the
threshold levels which is greater than the last reported speed, the
Trunk starts the speedReportingHoldOff timer. If the speed remains
above this threshold until the timer expires, the Trunk component
then reports the measuredSpeedToIf; otherwise the increase is not
reported."
::= { trk 318 }
trkSpdThEntry OBJECT-TYPE
SYNTAX TrkSpdThEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkSpdThTable."
INDEX {
trkIndex,
trkSpdThValue }
::= { trkSpdThTable 1 }
TrkSpdThEntry ::= SEQUENCE {
trkSpdThValue
Integer32,
trkSpdThRowStatus
RowStatus }
trkSpdThValue OBJECT-TYPE
SYNTAX Integer32 (0..268435455)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This variable represents both the value and the index for the
trkSpdThTable."
::= { trkSpdThEntry 1 }
trkSpdThRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS write-only
STATUS mandatory
DESCRIPTION
"This variable is used to control the addition and deletion
of individual values of the trkSpdThTable."
::= { trkSpdThEntry 2 }
trkPktBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of packets received by the Trunk.
It is a vector indexed by the emission priorities (ep0, ep1, and ep2)
of the packets. The highest emission priority is ep0. These counters
wrap around to zero when the maximum value is exceeded."
::= { trk 368 }
trkPktBpEntry OBJECT-TYPE
SYNTAX TrkPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkPktBpTable."
INDEX {
trkIndex,
trkPktBpIndex }
::= { trkPktBpTable 1 }
TrkPktBpEntry ::= SEQUENCE {
trkPktBpIndex
INTEGER,
trkPktBpValue
PassportCounter64 }
trkPktBpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the trkPktBpTable
specific index for the trkPktBpTable."
::= { trkPktBpEntry 1 }
trkPktBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkPktBpTable."
::= { trkPktBpEntry 2 }
trkDiscBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of packets received from the
remote module that have been discarded. It is a vector indexed by
the emission priorities (ep0, ep1 and ep2) of the packets. The
highest emission priority is ep0. These counters wrap around to zero
when the maximum value is exceeded.
Two main reasons that cause this counter to increment are:
(1) the remote protocol is not compatible to the local protocol stack
and,
(2) the packet cannot be forwarded due to either a recent loss of
connectivity or due to congestion.
DESCRIPTION"
::= { trk 369 }
trkDiscBpEntry OBJECT-TYPE
SYNTAX TrkDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkDiscBpTable."
INDEX {
trkIndex,
trkDiscBpIndex }
::= { trkDiscBpTable 1 }
TrkDiscBpEntry ::= SEQUENCE {
trkDiscBpIndex
INTEGER,
trkDiscBpValue
PassportCounter64 }
trkDiscBpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the trkDiscBpTable
specific index for the trkDiscBpTable."
::= { trkDiscBpEntry 1 }
trkDiscBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkDiscBpTable."
::= { trkDiscBpEntry 2 }
trkOctBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the octets coming from the remote module
which are received by the Trunk. It is a vector indexed by the
emission priorities (ep0, ep1 and ep2) of the packets. The highest
emission priority is ep0. These counters wrap around to zero when
the maximum value is exceeded."
::= { trk 370 }
trkOctBpEntry OBJECT-TYPE
SYNTAX TrkOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkOctBpTable."
INDEX {
trkIndex,
trkOctBpIndex }
::= { trkOctBpTable 1 }
TrkOctBpEntry ::= SEQUENCE {
trkOctBpIndex
INTEGER,
trkOctBpValue
PassportCounter64 }
trkOctBpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the trkOctBpTable
specific index for the trkOctBpTable."
::= { trkOctBpEntry 1 }
trkOctBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkOctBpTable."
::= { trkOctBpEntry 2 }
trkPorsStats OBJECT IDENTIFIER ::= { trk 6 }
trkPorsStatsRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkPorsStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entry controls the addition and deletion of
trkPorsStats components."
::= { trkPorsStats 1 }
trkPorsStatsRowStatusEntry OBJECT-TYPE
SYNTAX TrkPorsStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
trkPorsStats component."
INDEX {
trkIndex,
trkPorsStatsIndex }
::= { trkPorsStatsRowStatusTable 1 }
TrkPorsStatsRowStatusEntry ::= SEQUENCE {
trkPorsStatsRowStatus
RowStatus,
trkPorsStatsComponentName
DisplayString,
trkPorsStatsStorageType
StorageType,
trkPorsStatsIndex
NonReplicated }
trkPorsStatsRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
trkPorsStats components.
These components cannot be added nor deleted."
::= { trkPorsStatsRowStatusEntry 1 }
trkPorsStatsComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { trkPorsStatsRowStatusEntry 2 }
trkPorsStatsStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
trkPorsStats tables."
::= { trkPorsStatsRowStatusEntry 4 }
trkPorsStatsIndex OBJECT-TYPE
SYNTAX NonReplicated
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the trkPorsStats tables."
::= { trkPorsStatsRowStatusEntry 10 }
trkPorsStatsOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkPorsStatsOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This operational group provides the PORS Trunks interrupting and
normal traffic statistics for operator console display."
::= { trkPorsStats 10 }
trkPorsStatsOperEntry OBJECT-TYPE
SYNTAX TrkPorsStatsOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkPorsStatsOperTable."
INDEX {
trkIndex,
trkPorsStatsIndex }
::= { trkPorsStatsOperTable 1 }
TrkPorsStatsOperEntry ::= SEQUENCE {
trkPorsStatsPorsNormPktFromIf
PassportCounter64,
trkPorsStatsPorsNormDiscUnforwardFromIf
PassportCounter64,
trkPorsStatsPorsNormOctetFromIf
PassportCounter64,
trkPorsStatsPorsIntPktFromIf
PassportCounter64,
trkPorsStatsPorsIntDiscUnforwardFromIf
PassportCounter64,
trkPorsStatsPorsIntOctetFromIf
PassportCounter64 }
trkPorsStatsPorsNormPktFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of normal priority packets received
on the PORS Trunk normal priority queue. This counter wraps
around to zero when the maximum value is exceeded."
::= { trkPorsStatsOperEntry 1 }
trkPorsStatsPorsNormDiscUnforwardFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of normal priority packets
discarded from the PORS Trunk normal priority queue. This
counter wraps around to zero when the maximum value is
exceeded."
::= { trkPorsStatsOperEntry 2 }
trkPorsStatsPorsNormOctetFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of normal priority bytes received
on the PORS Trunk normal priority queue.This counter wraps
around to zero when the maximum value is exceeded."
::= { trkPorsStatsOperEntry 3 }
trkPorsStatsPorsIntPktFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of interrupting priority packets
received on the PORS Trunk interrupting priority queue. This
counter wraps around to zero when the maximum value is
exceeded."
::= { trkPorsStatsOperEntry 4 }
trkPorsStatsPorsIntDiscUnforwardFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of interrupting priority packets
discarded from the PORS Trunk interrupting priority queue. This
counter wraps around to zero when the maximum value is
exceeded."
::= { trkPorsStatsOperEntry 5 }
trkPorsStatsPorsIntOctetFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of interrupting priority bytes
received on the PORS Trunk interrupting priority queue. This
counter wraps around to zero when the maximum value is
exceeded."
::= { trkPorsStatsOperEntry 6 }
trkPorsStatsPktBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkPorsStatsPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of PORS packets received by the
Trunk. It is an array indexed by the emission priorities (ep0, ep1 and
ep2) and discard priorities (dp0, dp1, dp2 and dp3) of the packets.
The highest emission priority is ep0 and the least discardable
priority is dp0. These counters wrap around to zero when the
maximum value is exceeded."
::= { trkPorsStats 371 }
trkPorsStatsPktBpEntry OBJECT-TYPE
SYNTAX TrkPorsStatsPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkPorsStatsPktBpTable."
INDEX {
trkIndex,
trkPorsStatsIndex,
trkPorsStatsPktBpEpIndex,
trkPorsStatsPktBpDpIndex }
::= { trkPorsStatsPktBpTable 1 }
TrkPorsStatsPktBpEntry ::= SEQUENCE {
trkPorsStatsPktBpEpIndex
INTEGER,
trkPorsStatsPktBpDpIndex
INTEGER,
trkPorsStatsPktBpValue
PassportCounter64 }
trkPorsStatsPktBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkPorsStatsPktBpTable."
::= { trkPorsStatsPktBpEntry 1 }
trkPorsStatsPktBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkPorsStatsPktBpTable."
::= { trkPorsStatsPktBpEntry 2 }
trkPorsStatsPktBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkPorsStatsPktBpTable."
::= { trkPorsStatsPktBpEntry 3 }
trkPorsStatsDiscBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkPorsStatsDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of PORS packets received from the
remote module that have been discarded. It is an array indexed by
the emission priorities (ep0, ep1 and ep2) and discard priorities (dp0,
dp1, dp2 and dp3) of the packets. The highest emission priority is
ep0 and the least discardable priority is dp0. These counters wrap
around to zero when the maximum value is exceeded."
::= { trkPorsStats 372 }
trkPorsStatsDiscBpEntry OBJECT-TYPE
SYNTAX TrkPorsStatsDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkPorsStatsDiscBpTable."
INDEX {
trkIndex,
trkPorsStatsIndex,
trkPorsStatsDiscBpEpIndex,
trkPorsStatsDiscBpDpIndex }
::= { trkPorsStatsDiscBpTable 1 }
TrkPorsStatsDiscBpEntry ::= SEQUENCE {
trkPorsStatsDiscBpEpIndex
INTEGER,
trkPorsStatsDiscBpDpIndex
INTEGER,
trkPorsStatsDiscBpValue
PassportCounter64 }
trkPorsStatsDiscBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkPorsStatsDiscBpTable."
::= { trkPorsStatsDiscBpEntry 1 }
trkPorsStatsDiscBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkPorsStatsDiscBpTable."
::= { trkPorsStatsDiscBpEntry 2 }
trkPorsStatsDiscBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkPorsStatsDiscBpTable."
::= { trkPorsStatsDiscBpEntry 3 }
trkPorsStatsOctBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkPorsStatsOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of PORS octets received by the
Trunk. It is an array indexed by the emission priorities (ep0, ep1 and
ep2) and discard priorities (dp0, dp1, dp2 and dp3) of the packets.
The highest emission priority is ep0 and the least discardable
priority is dp0. These counters wrap around to zero when the
maximum value is exceeded."
::= { trkPorsStats 373 }
trkPorsStatsOctBpEntry OBJECT-TYPE
SYNTAX TrkPorsStatsOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkPorsStatsOctBpTable."
INDEX {
trkIndex,
trkPorsStatsIndex,
trkPorsStatsOctBpEpIndex,
trkPorsStatsOctBpDpIndex }
::= { trkPorsStatsOctBpTable 1 }
TrkPorsStatsOctBpEntry ::= SEQUENCE {
trkPorsStatsOctBpEpIndex
INTEGER,
trkPorsStatsOctBpDpIndex
INTEGER,
trkPorsStatsOctBpValue
PassportCounter64 }
trkPorsStatsOctBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkPorsStatsOctBpTable."
::= { trkPorsStatsOctBpEntry 1 }
trkPorsStatsOctBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkPorsStatsOctBpTable."
::= { trkPorsStatsOctBpEntry 2 }
trkPorsStatsOctBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkPorsStatsOctBpTable."
::= { trkPorsStatsOctBpEntry 3 }
trkFwdStats OBJECT IDENTIFIER ::= { trk 7 }
trkFwdStatsRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkFwdStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entry controls the addition and deletion of
trkFwdStats components."
::= { trkFwdStats 1 }
trkFwdStatsRowStatusEntry OBJECT-TYPE
SYNTAX TrkFwdStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
trkFwdStats component."
INDEX {
trkIndex,
trkFwdStatsIndex }
::= { trkFwdStatsRowStatusTable 1 }
TrkFwdStatsRowStatusEntry ::= SEQUENCE {
trkFwdStatsRowStatus
RowStatus,
trkFwdStatsComponentName
DisplayString,
trkFwdStatsStorageType
StorageType,
trkFwdStatsIndex
NonReplicated }
trkFwdStatsRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
trkFwdStats components.
These components cannot be added nor deleted."
::= { trkFwdStatsRowStatusEntry 1 }
trkFwdStatsComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { trkFwdStatsRowStatusEntry 2 }
trkFwdStatsStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
trkFwdStats tables."
::= { trkFwdStatsRowStatusEntry 4 }
trkFwdStatsIndex OBJECT-TYPE
SYNTAX NonReplicated
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the trkFwdStats tables."
::= { trkFwdStatsRowStatusEntry 10 }
trkFwdStatsOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkFwdStatsOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This operational group counts the Trunk or DpnGateway packet
forwarding traffic statistics for operator console display."
::= { trkFwdStats 10 }
trkFwdStatsOperEntry OBJECT-TYPE
SYNTAX TrkFwdStatsOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkFwdStatsOperTable."
INDEX {
trkIndex,
trkFwdStatsIndex }
::= { trkFwdStatsOperTable 1 }
TrkFwdStatsOperEntry ::= SEQUENCE {
trkFwdStatsFwdPktFromIf
PassportCounter64,
trkFwdStatsFwdDiscUnforwardFromIf
PassportCounter64,
trkFwdStatsFwdOctetFromIf
PassportCounter64 }
trkFwdStatsFwdPktFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of forwarding packets received by
the Trunk or DpnGateway. This counter wraps around to zero when
the maximum value is exceeded."
::= { trkFwdStatsOperEntry 1 }
trkFwdStatsFwdDiscUnforwardFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of forwarding packets discarded by
the Trunk or DpnGateway. This counter wraps around to zero when
the maximum value is exceeded."
::= { trkFwdStatsOperEntry 2 }
trkFwdStatsFwdOctetFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of forwarding bytes received by
the Trunk or DpnGateway. This counter wraps around to zero when
the maximum value is exceeded."
::= { trkFwdStatsOperEntry 3 }
trkVnsStats OBJECT IDENTIFIER ::= { trk 8 }
trkVnsStatsRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkVnsStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entry controls the addition and deletion of
trkVnsStats components."
::= { trkVnsStats 1 }
trkVnsStatsRowStatusEntry OBJECT-TYPE
SYNTAX TrkVnsStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
trkVnsStats component."
INDEX {
trkIndex,
trkVnsStatsIndex }
::= { trkVnsStatsRowStatusTable 1 }
TrkVnsStatsRowStatusEntry ::= SEQUENCE {
trkVnsStatsRowStatus
RowStatus,
trkVnsStatsComponentName
DisplayString,
trkVnsStatsStorageType
StorageType,
trkVnsStatsIndex
NonReplicated }
trkVnsStatsRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
trkVnsStats components.
These components cannot be added nor deleted."
::= { trkVnsStatsRowStatusEntry 1 }
trkVnsStatsComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { trkVnsStatsRowStatusEntry 2 }
trkVnsStatsStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
trkVnsStats tables."
::= { trkVnsStatsRowStatusEntry 4 }
trkVnsStatsIndex OBJECT-TYPE
SYNTAX NonReplicated
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the trkVnsStats tables."
::= { trkVnsStatsRowStatusEntry 10 }
trkVnsStatsOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkVnsStatsOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This operational group counts the Trunk virtual network traffic
statistics for operator console display."
::= { trkVnsStats 10 }
trkVnsStatsOperEntry OBJECT-TYPE
SYNTAX TrkVnsStatsOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkVnsStatsOperTable."
INDEX {
trkIndex,
trkVnsStatsIndex }
::= { trkVnsStatsOperTable 1 }
TrkVnsStatsOperEntry ::= SEQUENCE {
trkVnsStatsVnsPktFromIf
PassportCounter64,
trkVnsStatsVnsDiscUnforwardFromIf
PassportCounter64,
trkVnsStatsVnsOctetFromIf
PassportCounter64 }
trkVnsStatsVnsPktFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of virtual network packets received
by a Trunk component handling virtual network traffic. This counter
wraps around to zero when the maximum value is exceeded."
::= { trkVnsStatsOperEntry 1 }
trkVnsStatsVnsDiscUnforwardFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of virtual network packets
discarded by a Trunk component handling virtual network traffic.
This counter wraps around to zero when the maximum value is
exceeded."
::= { trkVnsStatsOperEntry 2 }
trkVnsStatsVnsOctetFromIf OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This attribute counts the number of virtual network bytes received
by a Trunk component handling virtual network traffic. This counter
wraps around to zero when the maximum value is exceeded."
::= { trkVnsStatsOperEntry 3 }
trkVnsStatsPktBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkVnsStatsPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of Virtual Network packets
received by the Trunk. It is an array indexed by the emission
priorities (ep0, ep1 and ep2) and discard priorities (dp0, dp1, dp2
and dp3) of the packets. The highest emission priority is ep0 and the
least discardable priority is dp0. These counters wrap around to zero
when the maximum value is exceeded."
::= { trkVnsStats 377 }
trkVnsStatsPktBpEntry OBJECT-TYPE
SYNTAX TrkVnsStatsPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkVnsStatsPktBpTable."
INDEX {
trkIndex,
trkVnsStatsIndex,
trkVnsStatsPktBpEpIndex,
trkVnsStatsPktBpDpIndex }
::= { trkVnsStatsPktBpTable 1 }
TrkVnsStatsPktBpEntry ::= SEQUENCE {
trkVnsStatsPktBpEpIndex
INTEGER,
trkVnsStatsPktBpDpIndex
INTEGER,
trkVnsStatsPktBpValue
PassportCounter64 }
trkVnsStatsPktBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkVnsStatsPktBpTable."
::= { trkVnsStatsPktBpEntry 1 }
trkVnsStatsPktBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkVnsStatsPktBpTable."
::= { trkVnsStatsPktBpEntry 2 }
trkVnsStatsPktBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkVnsStatsPktBpTable."
::= { trkVnsStatsPktBpEntry 3 }
trkVnsStatsDiscBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkVnsStatsDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of Virtual Network packets
received from the remote module that have been discarded by the
Trunk. It is an array indexed by the emission priorities (ep0, ep1 and
ep2) and discard priorities (dp0, dp1, dp2 and dp3) of the packets.
The highest emission priority is ep0 and the least discardable
priority is dp0. These counters wrap around to zero when the
maximum value is exceeded."
::= { trkVnsStats 378 }
trkVnsStatsDiscBpEntry OBJECT-TYPE
SYNTAX TrkVnsStatsDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkVnsStatsDiscBpTable."
INDEX {
trkIndex,
trkVnsStatsIndex,
trkVnsStatsDiscBpEpIndex,
trkVnsStatsDiscBpDpIndex }
::= { trkVnsStatsDiscBpTable 1 }
TrkVnsStatsDiscBpEntry ::= SEQUENCE {
trkVnsStatsDiscBpEpIndex
INTEGER,
trkVnsStatsDiscBpDpIndex
INTEGER,
trkVnsStatsDiscBpValue
PassportCounter64 }
trkVnsStatsDiscBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkVnsStatsDiscBpTable."
::= { trkVnsStatsDiscBpEntry 1 }
trkVnsStatsDiscBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkVnsStatsDiscBpTable."
::= { trkVnsStatsDiscBpEntry 2 }
trkVnsStatsDiscBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkVnsStatsDiscBpTable."
::= { trkVnsStatsDiscBpEntry 3 }
trkVnsStatsOctBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkVnsStatsOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of Virtual Network octets received
by the Trunk. It is an array indexed by the emission priorities (ep0,
ep1 and ep2) and discard priorities (dp0, dp1, dp2 and dp3) of the
packets. The highest emission priority is ep0 and the least
discardable priority is dp0. These counters wrap around to zero
when the maximum value is exceeded."
::= { trkVnsStats 379 }
trkVnsStatsOctBpEntry OBJECT-TYPE
SYNTAX TrkVnsStatsOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkVnsStatsOctBpTable."
INDEX {
trkIndex,
trkVnsStatsIndex,
trkVnsStatsOctBpEpIndex,
trkVnsStatsOctBpDpIndex }
::= { trkVnsStatsOctBpTable 1 }
TrkVnsStatsOctBpEntry ::= SEQUENCE {
trkVnsStatsOctBpEpIndex
INTEGER,
trkVnsStatsOctBpDpIndex
INTEGER,
trkVnsStatsOctBpValue
PassportCounter64 }
trkVnsStatsOctBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkVnsStatsOctBpTable."
::= { trkVnsStatsOctBpEntry 1 }
trkVnsStatsOctBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkVnsStatsOctBpTable."
::= { trkVnsStatsOctBpEntry 2 }
trkVnsStatsOctBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkVnsStatsOctBpTable."
::= { trkVnsStatsOctBpEntry 3 }
trkDprsStats OBJECT IDENTIFIER ::= { trk 10 }
trkDprsStatsRowStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkDprsStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entry controls the addition and deletion of
trkDprsStats components."
::= { trkDprsStats 1 }
trkDprsStatsRowStatusEntry OBJECT-TYPE
SYNTAX TrkDprsStatsRowStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A single entry in the table represents a single
trkDprsStats component."
INDEX {
trkIndex,
trkDprsStatsIndex }
::= { trkDprsStatsRowStatusTable 1 }
TrkDprsStatsRowStatusEntry ::= SEQUENCE {
trkDprsStatsRowStatus
RowStatus,
trkDprsStatsComponentName
DisplayString,
trkDprsStatsStorageType
StorageType,
trkDprsStatsIndex
NonReplicated }
trkDprsStatsRowStatus OBJECT-TYPE
SYNTAX RowStatus
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable is used as the basis for SNMP naming of
trkDprsStats components.
These components cannot be added nor deleted."
::= { trkDprsStatsRowStatusEntry 1 }
trkDprsStatsComponentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable provides the component's string name for
use with the ASCII Console Interface"
::= { trkDprsStatsRowStatusEntry 2 }
trkDprsStatsStorageType OBJECT-TYPE
SYNTAX StorageType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents the storage type value for the
trkDprsStats tables."
::= { trkDprsStatsRowStatusEntry 4 }
trkDprsStatsIndex OBJECT-TYPE
SYNTAX NonReplicated
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the index for the trkDprsStats tables."
::= { trkDprsStatsRowStatusEntry 10 }
trkDprsStatsPktBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkDprsStatsPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of DPRS packets received by the
Trunk. It is an array indexed by the emission priorities (ep0, ep1 and
ep2) and discard priorities (dp0, dp1, dp2 and dp3) of the packets.
The highest emission priority is ep0 and the least discardable
priority is dp0. These counters wrap around to zero when the
maximum value is exceeded."
::= { trkDprsStats 374 }
trkDprsStatsPktBpEntry OBJECT-TYPE
SYNTAX TrkDprsStatsPktBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkDprsStatsPktBpTable."
INDEX {
trkIndex,
trkDprsStatsIndex,
trkDprsStatsPktBpEpIndex,
trkDprsStatsPktBpDpIndex }
::= { trkDprsStatsPktBpTable 1 }
TrkDprsStatsPktBpEntry ::= SEQUENCE {
trkDprsStatsPktBpEpIndex
INTEGER,
trkDprsStatsPktBpDpIndex
INTEGER,
trkDprsStatsPktBpValue
PassportCounter64 }
trkDprsStatsPktBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkDprsStatsPktBpTable."
::= { trkDprsStatsPktBpEntry 1 }
trkDprsStatsPktBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkDprsStatsPktBpTable."
::= { trkDprsStatsPktBpEntry 2 }
trkDprsStatsPktBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkDprsStatsPktBpTable."
::= { trkDprsStatsPktBpEntry 3 }
trkDprsStatsDiscBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkDprsStatsDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of DPRS packets received from the
remote module that have been discarded by the Trunk. It is an array
indexed by the emission priorities (ep0, ep1 and ep2) and discard
priorities (dp0, dp1, dp2 and dp3) of the packets. The highest
emission priority is ep0 and the least discardable priority is dp0.
These counters wrap around to zero when the maximum value is
exceeded."
::= { trkDprsStats 375 }
trkDprsStatsDiscBpEntry OBJECT-TYPE
SYNTAX TrkDprsStatsDiscBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkDprsStatsDiscBpTable."
INDEX {
trkIndex,
trkDprsStatsIndex,
trkDprsStatsDiscBpEpIndex,
trkDprsStatsDiscBpDpIndex }
::= { trkDprsStatsDiscBpTable 1 }
TrkDprsStatsDiscBpEntry ::= SEQUENCE {
trkDprsStatsDiscBpEpIndex
INTEGER,
trkDprsStatsDiscBpDpIndex
INTEGER,
trkDprsStatsDiscBpValue
PassportCounter64 }
trkDprsStatsDiscBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkDprsStatsDiscBpTable."
::= { trkDprsStatsDiscBpEntry 1 }
trkDprsStatsDiscBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkDprsStatsDiscBpTable."
::= { trkDprsStatsDiscBpEntry 2 }
trkDprsStatsDiscBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkDprsStatsDiscBpTable."
::= { trkDprsStatsDiscBpEntry 3 }
trkDprsStatsOctBpTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrkDprsStatsOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This attribute counts the number of DPRS octets received by the
Trunk. It is an array indexed by the emission priorities (ep0, ep1 and
ep2) and discard priorities (dp0, dp1, dp2 and dp3) of the packets.
The highest emission priority is ep0 and the least discardable
priority is dp0. These counters wrap around to zero when the
maximum value is exceeded."
::= { trkDprsStats 376 }
trkDprsStatsOctBpEntry OBJECT-TYPE
SYNTAX TrkDprsStatsOctBpEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the trkDprsStatsOctBpTable."
INDEX {
trkIndex,
trkDprsStatsIndex,
trkDprsStatsOctBpEpIndex,
trkDprsStatsOctBpDpIndex }
::= { trkDprsStatsOctBpTable 1 }
TrkDprsStatsOctBpEntry ::= SEQUENCE {
trkDprsStatsOctBpEpIndex
INTEGER,
trkDprsStatsOctBpDpIndex
INTEGER,
trkDprsStatsOctBpValue
PassportCounter64 }
trkDprsStatsOctBpEpIndex OBJECT-TYPE
SYNTAX INTEGER {
ep0(0),
ep1(1),
ep2(2) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the next to last index for the
trkDprsStatsOctBpTable."
::= { trkDprsStatsOctBpEntry 1 }
trkDprsStatsOctBpDpIndex OBJECT-TYPE
SYNTAX INTEGER {
dp0(0),
dp1(1),
dp2(2),
dp3(3) }
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable represents the final index for the
trkDprsStatsOctBpTable."
::= { trkDprsStatsOctBpEntry 2 }
trkDprsStatsOctBpValue OBJECT-TYPE
SYNTAX PassportCounter64
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable represents an individual value for the
trkDprsStatsOctBpTable."
::= { trkDprsStatsOctBpEntry 3 }
trunksGroup OBJECT IDENTIFIER ::= { trunksMIB 1 }
trunksGroupBE OBJECT IDENTIFIER ::= { trunksGroup 5 }
trunksGroupBE00 OBJECT IDENTIFIER ::= { trunksGroupBE 1 }
trunksGroupBE00A OBJECT IDENTIFIER ::= { trunksGroupBE00 2 }
trunksCapabilities OBJECT IDENTIFIER ::= { trunksMIB 3 }
trunksCapabilitiesBE OBJECT IDENTIFIER ::= { trunksCapabilities 5 }
trunksCapabilitiesBE00 OBJECT IDENTIFIER ::= { trunksCapabilitiesBE 1 }
trunksCapabilitiesBE00A OBJECT IDENTIFIER ::= { trunksCapabilitiesBE00 2 }
END