ADSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Counter32, Gauge32,
NOTIFICATION-TYPE,
transmission, Unsigned32 FROM SNMPv2-SMI
RowStatus,
TruthValue, VariablePointer FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
ifIndex FROM IF-MIB
PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
AdslPerfCurrDayCount,
AdslPerfPrevDayCount,
AdslPerfTimeElapsed,
AdslLineCodingType FROM ADSL-TC-MIB
;
adslMIB MODULE-IDENTITY
LAST-UPDATED "9908190000Z"
ORGANIZATION "IETF ADSL MIB Working Group"
CONTACT-INFO
"
Gregory Bathrick
AG Communication Systems
A Subsidiary of Lucent Technologies
2500 W Utopia Rd.
Phoenix, AZ 85027 USA
Tel: +1 602-582-7679
Fax: +1 602-582-7697
E-mail: bathricg@agcs.com
Faye Ly
Copper Mountain Networks
Norcal Office
2470 Embarcadero Way
Palo Alto, CA 94303
Tel: +1 650-858-8500
Fax: +1 650-858-8085
E-Mail: faye@coppermountain.com
(ADSL Forum input only)
John Burgess
Predictive Systems, Inc.
25A Vreeland Rd.
Florham Park, NJ 07932 USA
Tel: +1 973-301-5610
Fax: +1 973-301-5699
E-mail: jtburgess@predictive.com
IETF ADSL MIB Working Group (adsl@xlist.agcs.com)
"
DESCRIPTION
"The MIB module defining objects for the management of a pair of
ADSL modems at each end of the ADSL line. Each such line has
an entry in an ifTable which may include multiple modem lines.
An agent may reside at either end of the ADSL line however the
MIB is designed to require no management communication between
them beyond that inherent in the low-level ADSL line protocol.
The agent may monitor and control this protocol for its needs.
ADSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus an ADSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to adsl(94), fast(125), and
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.
Naming Conventions:
Atuc -- (ATUC) modem at near (Central) end of line
Atur -- (ATUR) modem at Remote end of line
Curr -- Current
Prev -- Previous
Atn -- Attenuation
ES -- Errored Second.
LCS -- Line Code Specific
Lof -- Loss of Frame
Lol -- Loss of Link
Los -- Loss of Signal
Lpr -- Loss of Power
xxxs-- interval of Seconds in which xxx occurs
(e.g., xxx=Lof, Los, Lpr)
Max -- Maximum
Mgn -- Margin
Min -- Minimum
Psd -- Power Spectral Density
Snr -- Signal to Noise Ratio
Tx -- Transmit
Blks-- Blocks, a data unit, see
adslAtuXChanCrcBlockLength
"
REVISION "9908190000Z" DESCRIPTION "Initial Version, published as RFC 2662"
::= { transmission 94 }
adslLineMib OBJECT IDENTIFIER ::= { adslMIB 1 }
adslMibObjects OBJECT IDENTIFIER ::= { adslLineMib 1 }
AdslLineProfileName ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This data type is used to uniquely identify a row in
an ADSL Line Profile Table."
SYNTAX SnmpAdminString ( 1..32 )
adslLineTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { adslMibObjects 1 }
adslLineEntry OBJECT-TYPE
SYNTAX AdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in adslLineTable."
INDEX { ifIndex }
::= { adslLineTable 1 }
AdslLineEntry ::=
SEQUENCE {
adslLineCoding AdslLineCodingType,
adslLineType INTEGER,
adslLineSpecific VariablePointer,
adslLineConfProfile SnmpAdminString,
adslLineAlarmConfProfile SnmpAdminString
}
adslLineCoding OBJECT-TYPE
SYNTAX AdslLineCodingType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the ADSL coding type used on this
line."
::= { adslLineEntry 1 }
adslLineType OBJECT-TYPE
SYNTAX INTEGER {
noChannel (1), fastOnly (2), interleavedOnly (3), fastOrInterleaved (4),fastAndInterleaved (5)}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defines the type of ADSL physical line
entity that exists, by defining whether and how
the line is channelized. If the line is channelized,
the value will be other than noChannel(1). This
object defines which channel type(s) are supported.
In the case that the line is channelized, the manager
can use the ifStackTable to determine the ifIndex for
the associated channel(s)."
::= { adslLineEntry 2 }
adslLineSpecific OBJECT-TYPE
SYNTAX VariablePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"OID instance in vendor-specific MIB. The Instance may
be used to determine shelf/slot/port of the ATUC
interface in a DSLAM."
::= { adslLineEntry 3 }
adslLineConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the ADSL Line Configuration Profile Table,
(adslLineConfProfileTable), which applies for this
ADSL line, and channels if applicable.
For `dynamic' mode, in the case which the
configuration profile has not been set, the
value will be set to `DEFVAL'.
If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only."
::= { adslLineEntry 4 }
adslLineAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the ADSL Line Alarm Configuration Profile Table,
(adslLineAlarmConfProfileTable), which applies to this
ADSL line, and channels if applicable.
For `dynamic' mode, in the case which the
alarm profile has not been set, the
value will be set to `DEFVAL'.
If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only."
::= { adslLineEntry 5 }
adslAtucPhysTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAtucPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATUC.
Each row contains the Physical Layer Parameters
table for that ATUC. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { adslMibObjects 2 }
adslAtucPhysEntry OBJECT-TYPE
SYNTAX AdslAtucPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the adslAtucPhysTable."
INDEX { ifIndex }
::= { adslAtucPhysTable 1 }
AdslAtucPhysEntry ::=
SEQUENCE {
adslAtucInvSerialNumber SnmpAdminString,
adslAtucInvVendorID SnmpAdminString,
adslAtucInvVersionNumber SnmpAdminString,
adslAtucCurrSnrMgn INTEGER,
adslAtucCurrAtn Gauge32,
adslAtucCurrStatus BITS,
adslAtucCurrOutputPwr INTEGER,
adslAtucCurrAttainableRate Gauge32
}
adslAtucInvSerialNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific string that identifies the
vendor equipment."
::= { adslAtucPhysEntry 1 }
adslAtucInvVendorID OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor ID code is a copy of the binary
vendor identification field defined by the
PHY[10] and expressed as readable characters."
REFERENCE "ANSI T1.413[10]"
::= { adslAtucPhysEntry 2 }
adslAtucInvVersionNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific version number sent by this ATU
as part of the initialization messages. It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters."
REFERENCE "ANSI T1.413[10]"
::= { adslAtucPhysEntry 3 }
adslAtucCurrSnrMgn OBJECT-TYPE
SYNTAX INTEGER (-640..640)
UNITS "tenth dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Noise Margin as seen by this ATU with respect to its
received signal in tenth dB."
::= { adslAtucPhysEntry 4 }
adslAtucCurrAtn OBJECT-TYPE
SYNTAX Gauge32(0..630)
UNITS "tenth dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured difference in the total power transmitted by
the peer ATU and the total power received by this ATU."
::= { adslAtucPhysEntry 5 }
adslAtucCurrStatus OBJECT-TYPE
SYNTAX BITS {
noDefect(0),
lossOfFraming(1),
lossOfSignal(2),
lossOfPower(3),
lossOfSignalQuality(4),
lossOfLink(5),
dataInitFailure(6),
configInitFailure(7),
protocolInitFailure(8),
noPeerAtuPresent(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state of the ATUC line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUC failure due to not
receiving valid frame.
2 lossOfSignal ATUC failure due to not
receiving signal.
3 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
5 lossOfLink ATUC failure due to inability
to link with ATUR.
6 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
7 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
8 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
9 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
This is intended to supplement ifOperStatus."
::= { adslAtucPhysEntry 6 }
adslAtucCurrOutputPwr OBJECT-TYPE
SYNTAX INTEGER (-310..310)
UNITS "tenth dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence."
::= { adslAtucPhysEntry 7 }
adslAtucCurrAttainableRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate."
::= { adslAtucPhysEntry 8 }
adslAturPhysTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAturPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATUR
Each row contains the Physical Layer Parameters
table for that ATUR. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { adslMibObjects 3 }
adslAturPhysEntry OBJECT-TYPE
SYNTAX AdslAturPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the adslAturPhysTable."
INDEX { ifIndex }
::= { adslAturPhysTable 1 }
AdslAturPhysEntry ::=
SEQUENCE {
adslAturInvSerialNumber SnmpAdminString,
adslAturInvVendorID SnmpAdminString,
adslAturInvVersionNumber SnmpAdminString,
adslAturCurrSnrMgn INTEGER,
adslAturCurrAtn Gauge32,
adslAturCurrStatus BITS,
adslAturCurrOutputPwr INTEGER,
adslAturCurrAttainableRate Gauge32
}
adslAturInvSerialNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific string that identifies the
vendor equipment."
::= { adslAturPhysEntry 1 }
adslAturInvVendorID OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor ID code is a copy of the binary
vendor identification field defined by the
PHY[10] and expressed as readable characters."
REFERENCE "ANSI T1.413"
::= { adslAturPhysEntry 2 }
adslAturInvVersionNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific version number sent by this ATU
as part of the initialization messages. It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters."
REFERENCE "ANSI T1.413"
::= { adslAturPhysEntry 3 }
adslAturCurrSnrMgn OBJECT-TYPE
SYNTAX INTEGER (-640..640)
UNITS "tenth dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Noise Margin as seen by this ATU with respect to its
received signal in tenth dB."
::= { adslAturPhysEntry 4 }
adslAturCurrAtn OBJECT-TYPE
SYNTAX Gauge32(0..630)
UNITS "tenth dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured difference in the total power transmitted by
the peer ATU and the total power received by this ATU."
::= { adslAturPhysEntry 5 }
adslAturCurrStatus OBJECT-TYPE
SYNTAX BITS {
noDefect(0),
lossOfFraming(1),
lossOfSignal(2),
lossOfPower(3),
lossOfSignalQuality(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state of the ATUR line. This is a
bit-map of possible conditions. Due to the isolation
of the ATUR when line problems occur, many state
conditions like loss of power, loss of quality signal,
and initialization errors, can not be determined.
While trouble shooting ATUR, also use object,
adslAtucCurrStatus. The various bit positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUR failure due to not
receiving valid frame
2 lossOfSignal ATUR failure due to not
receiving signal
3 lossOfPower ATUR failure due to loss of
power
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the
bit-error-rate exceeds 10^-7.
This is intended to supplement ifOperStatus."
::= { adslAturPhysEntry 6 }
adslAturCurrOutputPwr OBJECT-TYPE
SYNTAX INTEGER (-310..310)
UNITS "tenth dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence."
::= { adslAturPhysEntry 7 }
adslAturCurrAttainableRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the maximum currently attainable data rate
by the ATU. This value will be equal or greater than
the current line rate."
::= { adslAturPhysEntry 8 }
adslAtucChanTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAtucChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATUC channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125)."
::= { adslMibObjects 4 }
adslAtucChanEntry OBJECT-TYPE
SYNTAX AdslAtucChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the adslAtucChanTable."
INDEX { ifIndex }
::= { adslAtucChanTable 1 }
AdslAtucChanEntry ::=
SEQUENCE {
adslAtucChanInterleaveDelay Gauge32,
adslAtucChanCurrTxRate Gauge32,
adslAtucChanPrevTxRate Gauge32,
adslAtucChanCrcBlockLength Gauge32
}
adslAtucChanInterleaveDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milli-seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interleave Delay for this channel.
Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their placement
in the bit stream at the interleaver output.
Larger numbers provide greater separation between
consecutive input bytes in the output bit stream
allowing for improved impulse noise immunity at
the expense of payload latency.
In the case where the ifType is Fast(125), use
noSuchObject."
::= { adslAtucChanEntry 1 }
adslAtucChanCurrTxRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual transmit rate on this channel."
::= { adslAtucChanEntry 2 }
adslAtucChanPrevTxRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The rate at the time of the last
adslAtucRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.
Rate changes less than adslAtucThresh(*)RateDown
or less than adslAtucThresh(*)RateUp will not
cause a trap or cause this object to change.
(*) == Fast or Interleave.
See AdslLineAlarmConfProfileEntry."
::= { adslAtucChanEntry 3 }
adslAtucChanCrcBlockLength OBJECT-TYPE
SYNTAX Gauge32
UNITS "byte"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the length of the channel data-block
on which the CRC operates. Refer to Line Code
Specific MIBs, [11] and [12] for more
information."
::= { adslAtucChanEntry 4 }
adslAturChanTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAturChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATUR channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125)."
::= { adslMibObjects 5 }
adslAturChanEntry OBJECT-TYPE
SYNTAX AdslAturChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the adslAturChanTable."
INDEX { ifIndex }
::= { adslAturChanTable 1 }
AdslAturChanEntry ::=
SEQUENCE {
adslAturChanInterleaveDelay Gauge32,
adslAturChanCurrTxRate Gauge32,
adslAturChanPrevTxRate Gauge32,
adslAturChanCrcBlockLength Gauge32
}
adslAturChanInterleaveDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milli-seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interleave Delay for this channel.
Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their placement
in the bit stream at the interleaver output.
Larger numbers provide greater separation between
consecutive input bytes in the output bit stream
allowing for improved impulse noise immunity at
the expense of payload latency.
In the case where the ifType is Fast(125), use
noSuchObject."
::= { adslAturChanEntry 1 }
adslAturChanCurrTxRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual transmit rate on this channel."
::= { adslAturChanEntry 2 }
adslAturChanPrevTxRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The rate at the time of the last
adslAturRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.
Rate changes less than adslAturThresh(*)RateDown
or less than adslAturThresh(*)RateUp will not
cause a trap or cause this object to change.
(*) == Fast or Interleave.
See AdslLineAlarmConfProfileEntry."
::= { adslAturChanEntry 3 }
adslAturChanCrcBlockLength OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the length of the channel data-block
on which the CRC operates. Refer to Line Code
Specific MIBs, [11] and [12] for more
information."
::= { adslAturChanEntry 4 }
adslAtucPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAtucPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATUC.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { adslMibObjects 6 }
adslAtucPerfDataEntry OBJECT-TYPE
SYNTAX AdslAtucPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in adslAtucPerfDataTable."
INDEX { ifIndex }
::= { adslAtucPerfDataTable 1 }
AdslAtucPerfDataEntry ::=
SEQUENCE {
adslAtucPerfLofs Counter32,
adslAtucPerfLoss Counter32,
adslAtucPerfLols Counter32,
adslAtucPerfLprs Counter32,
adslAtucPerfESs Counter32,
adslAtucPerfInits Counter32,
adslAtucPerfValidIntervals INTEGER,
adslAtucPerfInvalidIntervals INTEGER,
adslAtucPerfCurr15MinTimeElapsed AdslPerfTimeElapsed,
adslAtucPerfCurr15MinLofs PerfCurrentCount,
adslAtucPerfCurr15MinLoss PerfCurrentCount,
adslAtucPerfCurr15MinLols PerfCurrentCount,
adslAtucPerfCurr15MinLprs PerfCurrentCount,
adslAtucPerfCurr15MinESs PerfCurrentCount,
adslAtucPerfCurr15MinInits PerfCurrentCount,
adslAtucPerfCurr1DayTimeElapsed AdslPerfTimeElapsed,
adslAtucPerfCurr1DayLofs AdslPerfCurrDayCount,
adslAtucPerfCurr1DayLoss AdslPerfCurrDayCount,
adslAtucPerfCurr1DayLols AdslPerfCurrDayCount,
adslAtucPerfCurr1DayLprs AdslPerfCurrDayCount,
adslAtucPerfCurr1DayESs AdslPerfCurrDayCount,
adslAtucPerfCurr1DayInits AdslPerfCurrDayCount,
adslAtucPerfPrev1DayMoniSecs INTEGER,
adslAtucPerfPrev1DayLofs AdslPerfPrevDayCount,
adslAtucPerfPrev1DayLoss AdslPerfPrevDayCount,
adslAtucPerfPrev1DayLols AdslPerfPrevDayCount,
adslAtucPerfPrev1DayLprs AdslPerfPrevDayCount,
adslAtucPerfPrev1DayESs AdslPerfPrevDayCount,
adslAtucPerfPrev1DayInits AdslPerfPrevDayCount
}
adslAtucPerfLofs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Loss of Framing failures since
agent reset."
::= { adslAtucPerfDataEntry 1 }
adslAtucPerfLoss OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Loss of Signal failures since
agent reset."
::= { adslAtucPerfDataEntry 2 }
adslAtucPerfLols OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Loss of Link failures since
agent reset."
::= { adslAtucPerfDataEntry 3 }
adslAtucPerfLprs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Loss of Power failures since
agent reset."
::= { adslAtucPerfDataEntry 4 }
adslAtucPerfESs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Errored Seconds since agent
reset. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects."
::= { adslAtucPerfDataEntry 5 }
adslAtucPerfInits OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts since
agent reset. Includes both successful and failed
attempts."
::= { adslAtucPerfDataEntry 6 }
adslAtucPerfValidIntervals OBJECT-TYPE
SYNTAX INTEGER(0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of previous 15-minute intervals in the
interval table for which data was collected. Given
that <n> is the maximum # of intervals supported.
The value will be <n> unless the measurement was
(re-)started within the last (<n>*15) minutes, in which
case the value will be the number of complete 15
minute intervals for which the agent has at least
some data. In certain cases (e.g., in the case
where the agent is a proxy) it is possible that some
intervals are unavailable. In this case, this
interval is the maximum interval number for
which data is available."
::= { adslAtucPerfDataEntry 7 }
adslAtucPerfInvalidIntervals OBJECT-TYPE
SYNTAX INTEGER(0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of intervals in the range from
0 to the value of adslAtucPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not available
(e.g., in proxy situations)."
::= { adslAtucPerfDataEntry 8 }
adslAtucPerfCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX AdslPerfTimeElapsed(0..899)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { adslAtucPerfDataEntry 9 }
adslAtucPerfCurr15MinLofs OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the current 15 minute interval
when there was Loss of Framing."
::= { adslAtucPerfDataEntry 10 }
adslAtucPerfCurr15MinLoss OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the current 15 minute interval
when there was Loss of Signal."
::= { adslAtucPerfDataEntry 11 }
adslAtucPerfCurr15MinLols OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the current 15 minute interval
when there was Loss of Link."
::= { adslAtucPerfDataEntry 12 }
adslAtucPerfCurr15MinLprs OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the current 15 minute interval
when there was Loss of Power."
::= { adslAtucPerfDataEntry 13 }
adslAtucPerfCurr15MinESs OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds in the current 15 minute
interval. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects."
::= { adslAtucPerfDataEntry 14 }
adslAtucPerfCurr15MinInits OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts in the
current 15 minute interval. Includes both successful
and failed attempts."
::= { adslAtucPerfDataEntry 15 }
adslAtucPerfCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX AdslPerfTimeElapsed(0..86399)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the
beginning of the current 1-day interval."
::= { adslAtucPerfDataEntry 16 }
adslAtucPerfCurr1DayLofs OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of seconds when there was Loss of
Framing during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed."
::= { adslAtucPerfDataEntry 17 }
adslAtucPerfCurr1DayLoss OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of seconds when there was Loss of
Signal during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed."
::= { adslAtucPerfDataEntry 18 }
adslAtucPerfCurr1DayLols OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of seconds when there was Loss of
Link during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed."
::= { adslAtucPerfDataEntry 19 }
adslAtucPerfCurr1DayLprs OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of seconds when there was Loss of
Power during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed."
::= { adslAtucPerfDataEntry 20 }
adslAtucPerfCurr1DayESs OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds during the current day as
measured by adslAtucPerfCurr1DayTimeElapsed.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects."
::= { adslAtucPerfDataEntry 21 }
adslAtucPerfCurr1DayInits OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts in the
day as measured by adslAtucPerfCurr1DayTimeElapsed.
Includes both successful and failed attempts."
::= { adslAtucPerfDataEntry 22 }
adslAtucPerfPrev1DayMoniSecs OBJECT-TYPE
SYNTAX INTEGER(0..86400)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the previous 1-day interval
over which the performance monitoring information
is actually counted. This value will be the same as
the interval duration except in a situation where
performance monitoring data could not be collected
for any reason."
::= { adslAtucPerfDataEntry 23 }
adslAtucPerfPrev1DayLofs OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Framing within the most recent previous
1-day period."
::= { adslAtucPerfDataEntry 24 }
adslAtucPerfPrev1DayLoss OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Signal within the most recent previous
1-day period."
::= { adslAtucPerfDataEntry 25 }
adslAtucPerfPrev1DayLols OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Link within the most recent previous
1-day period."
::= { adslAtucPerfDataEntry 26 }
adslAtucPerfPrev1DayLprs OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Power within the most recent previous
1-day period."
::= { adslAtucPerfDataEntry 27 }
adslAtucPerfPrev1DayESs OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds within the most recent
previous 1-day period. The errored second parameter is
a count of one-second intervals containing one or more
crc anomalies, or one or more los or sef defects."
::= { adslAtucPerfDataEntry 28 }
adslAtucPerfPrev1DayInits OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts in the most
recent previous 1-day period. Includes both successful
and failed attempts."
::= { adslAtucPerfDataEntry 29 }
adslAturPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAturPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATUR.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { adslMibObjects 7 }
adslAturPerfDataEntry OBJECT-TYPE
SYNTAX AdslAturPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in adslAturPerfDataTable."
INDEX { ifIndex }
::= { adslAturPerfDataTable 1 }
AdslAturPerfDataEntry ::=
SEQUENCE {
adslAturPerfLofs Counter32,
adslAturPerfLoss Counter32,
adslAturPerfLprs Counter32,
adslAturPerfESs Counter32,
adslAturPerfValidIntervals INTEGER,
adslAturPerfInvalidIntervals INTEGER,
adslAturPerfCurr15MinTimeElapsed AdslPerfTimeElapsed,
adslAturPerfCurr15MinLofs PerfCurrentCount,
adslAturPerfCurr15MinLoss PerfCurrentCount,
adslAturPerfCurr15MinLprs PerfCurrentCount,
adslAturPerfCurr15MinESs PerfCurrentCount,
adslAturPerfCurr1DayTimeElapsed AdslPerfTimeElapsed,
adslAturPerfCurr1DayLofs AdslPerfCurrDayCount,
adslAturPerfCurr1DayLoss AdslPerfCurrDayCount,
adslAturPerfCurr1DayLprs AdslPerfCurrDayCount,
adslAturPerfCurr1DayESs AdslPerfCurrDayCount,
adslAturPerfPrev1DayMoniSecs INTEGER,
adslAturPerfPrev1DayLofs AdslPerfPrevDayCount,
adslAturPerfPrev1DayLoss AdslPerfPrevDayCount,
adslAturPerfPrev1DayLprs AdslPerfPrevDayCount,
adslAturPerfPrev1DayESs AdslPerfPrevDayCount
}
adslAturPerfLofs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Loss of Framing failures since
agent reset."
::= { adslAturPerfDataEntry 1 }
adslAturPerfLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Loss of Signal failures since
agent reset."
::= { adslAturPerfDataEntry 2 }
adslAturPerfLprs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Loss of Power failures since
agent reset."
::= { adslAturPerfDataEntry 3 }
adslAturPerfESs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of Errored Seconds since agent
reset. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects."
::= { adslAturPerfDataEntry 4 }
adslAturPerfValidIntervals OBJECT-TYPE
SYNTAX INTEGER(0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of previous 15-minute intervals in the
interval table for which data was collected. Given
that <n> is the maximum # of intervals supported.
The value will be <n> unless the measurement was
(re-)started within the last (<n>*15) minutes, in which
case the value will be the number of complete 15
minute intervals for which the agent has at least
some data. In certain cases (e.g., in the case
where the agent is a proxy) it is possible that some
intervals are unavailable. In this case, this
interval is the maximum interval number for
which data is available."
::= { adslAturPerfDataEntry 5 }
adslAturPerfInvalidIntervals OBJECT-TYPE
SYNTAX INTEGER(0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of intervals in the range from
0 to the value of adslAturPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not available
(e.g., in proxy situations)."
::= { adslAturPerfDataEntry 6 }
adslAturPerfCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX AdslPerfTimeElapsed(0..899)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { adslAturPerfDataEntry 7 }
adslAturPerfCurr15MinLofs OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the current 15 minute interval
when there was Loss of Framing."
::= { adslAturPerfDataEntry 8 }
adslAturPerfCurr15MinLoss OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the current 15 minute interval
when there was Loss of Signal."
::= { adslAturPerfDataEntry 9 }
adslAturPerfCurr15MinLprs OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the current 15 minute interval
when there was Loss of Power."
::= { adslAturPerfDataEntry 10 }
adslAturPerfCurr15MinESs OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds in the current 15 minute
interval. The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects."
::= { adslAturPerfDataEntry 11 }
adslAturPerfCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX AdslPerfTimeElapsed(0..86399)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the
beginning of the current 1-day interval."
::= { adslAturPerfDataEntry 12 }
adslAturPerfCurr1DayLofs OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of seconds when there was Loss
of Framing during the current day as measured by
adslAturPerfCurr1DayTimeElapsed."
::= { adslAturPerfDataEntry 13 }
adslAturPerfCurr1DayLoss OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of seconds when there was Loss
of Signal during the current day as measured by
adslAturPerfCurr1DayTimeElapsed."
::= { adslAturPerfDataEntry 14 }
adslAturPerfCurr1DayLprs OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the number of seconds when there was Loss
of Power during the current day as measured by
adslAturPerfCurr1DayTimeElapsed."
::= { adslAturPerfDataEntry 15 }
adslAturPerfCurr1DayESs OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds during the current day as
measured by adslAturPerfCurr1DayTimeElapsed.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects."
::= { adslAturPerfDataEntry 16 }
adslAturPerfPrev1DayMoniSecs OBJECT-TYPE
SYNTAX INTEGER(0..86400)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the previous 1-day interval
over which the performance monitoring information
is actually counted. This value will be the same as
the interval duration except in a situation where
performance monitoring data could not be collected
for any reason."
::= { adslAturPerfDataEntry 17 }
adslAturPerfPrev1DayLofs OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Framing within the most recent previous
1-day period."
::= { adslAturPerfDataEntry 18 }
adslAturPerfPrev1DayLoss OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Signal within the most recent previous
1-day period."
::= { adslAturPerfDataEntry 19 }
adslAturPerfPrev1DayLprs OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Power within the most recent previous
1-day period."
::= { adslAturPerfDataEntry 20 }
adslAturPerfPrev1DayESs OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds within the most recent
previous 1-day period. The errored second parameter is
a count of one-second intervals containing one or more
crc anomalies, or one or more los or sef defects."
::= { adslAturPerfDataEntry 21 }
adslAtucIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAtucIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATUC
performance data collection interval.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { adslMibObjects 8 }
adslAtucIntervalEntry OBJECT-TYPE
SYNTAX AdslAtucIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the adslAtucIntervalTable."
INDEX { ifIndex, adslAtucIntervalNumber }
::= { adslAtucIntervalTable 1 }
AdslAtucIntervalEntry ::=
SEQUENCE {
adslAtucIntervalNumber INTEGER,
adslAtucIntervalLofs PerfIntervalCount,
adslAtucIntervalLoss PerfIntervalCount,
adslAtucIntervalLols PerfIntervalCount,
adslAtucIntervalLprs PerfIntervalCount,
adslAtucIntervalESs PerfIntervalCount,
adslAtucIntervalInits PerfIntervalCount,
adslAtucIntervalValidData TruthValue
}
adslAtucIntervalNumber OBJECT-TYPE
SYNTAX INTEGER(1