DECNET-PHIV-MIB DEFINITIONS ::= BEGIN
IMPORTS
Gauge
FROM RFC1155-SMI
OBJECT-TYPE
FROM RFC-1212
mib-2, DisplayString
FROM RFC1213-MIB;
phiv OBJECT IDENTIFIER ::= { mib-2 18 }
PhivAddr ::= OCTET STRING (SIZE (2))
PhivCounter ::= INTEGER
InterfaceIndex ::= INTEGER
phivSystem OBJECT IDENTIFIER ::= { phiv 1 }
phivManagement OBJECT IDENTIFIER ::= { phiv 2 }
session OBJECT IDENTIFIER ::= { phiv 3 }
end OBJECT IDENTIFIER ::= { phiv 4 }
routing OBJECT IDENTIFIER ::= { phiv 5 }
circuit OBJECT IDENTIFIER ::= { phiv 6 }
ddcmp OBJECT IDENTIFIER ::= { phiv 7 }
control OBJECT IDENTIFIER ::= { phiv 8 }
ethernet OBJECT IDENTIFIER ::= { phiv 9 }
counters OBJECT IDENTIFIER ::= { phiv 10 }
adjacency OBJECT IDENTIFIER ::= { phiv 11 }
line OBJECT IDENTIFIER ::= { phiv 12 }
nonBroadcastLine OBJECT IDENTIFIER ::= { phiv 14 }
area OBJECT IDENTIFIER ::= { phiv 15 }
phivSystemState OBJECT-TYPE
SYNTAX INTEGER {
on (1),
off (2),
shut (3),
restricted (4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This represents the operational state of the executor
node.
The possible states are:
ON Allows logical links.
OFF Allows no new links, terminates existing
links, and stops routing traffic through.
SHUT Allows no new logical links, does not
destroy existing logical links, and goes
to the OFF state when all logical links are
gone.
RESTRICTED Allows no new incoming logical links from
other nodes.
NOTE: These values are incremented by one compared to
the standard DECnet values in order to maintain
compliance with RFC 1155)."
::= { phivSystem 1 }
phivExecIdent OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..32))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This is a text string that describes the executor node
(for example, 'Research Lab'). The string is up to 32
characters of any type."
::= { phivSystem 2 }
phivMgmtMgmtVers OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the read-only Network Management Version,
consisting of the version number, the Engineering
Change Order (ECO) number, and the user ECO number
(for example, 3.0.0). This parameter applies to the
executor node only."
::= { phivManagement 1 }
phivSessionSystemName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..6))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Name to be associated with the node identification.
Only one name can be assigned to a node address or a
circuit identification. No name should be used more than
once in a DECnet network. Node-name is one to six upper
case alphanumeric characters with at least one alpha
character. A length of 0 indicates no name."
::= { session 1 }
phivSessionInTimer OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum duration between the
time a connect is received for a process at the
executor node and the time that process accepts or
rejects it. If the connect is not accepted or rejected
by the user within the number of seconds specified,
Session Control rejects it for the user. A value of 0
indicates no timer is running."
::= { session 2 }
phivSessionOutTimer OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the duration between the time the
executor requests a connect and the time that connect is
acknowledged by the destination node. If the connect is
not acknowledged within the number of seconds
specified, Session Control returns an error. A value of 0
indicates no timer is running."
::= { session 3 }
phivEndRemoteTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhivEndRemoteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the state of sessions between the
node under study and the nodes found in the table."
::= { end 1 }
phivEndRemoteEntry OBJECT-TYPE
SYNTAX PhivEndRemoteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about a particular remote node as seen
from the end communication layer."
INDEX { phivEndRemoteHostNodeID }
::= { phivEndRemoteTable 1 }
PhivEndRemoteEntry ::=
SEQUENCE {
phivEndRemoteHostNodeID
PhivAddr,
phivEndRemoteState
INTEGER,
phivEndCircuitIndex
INTEGER,
phivEndActiveLinks
INTEGER,
phivEndDelay
INTEGER
}
phivEndRemoteHostNodeID OBJECT-TYPE
SYNTAX PhivAddr ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the address of the remote node to be
evaluated."
::= { phivEndRemoteEntry 1 }
phivEndRemoteState OBJECT-TYPE
SYNTAX INTEGER {
on (1),
off (2),
shut (3),
restricted (4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This represents the operational state of the remote node
being evaluated.
The possible states are:
ON Allows logical links.
OFF Allows no new links, terminates existing
links, and stops routing traffic through.
SHUT Allows no new logical links, does not
destroy existing logical links, and goes
to the OFF state when all logical links are
gone.
RESTRICTED Allows no new incoming logical links from
other nodes.
NOTE: These values are incremented by one compared to
the standard DECnet values in order to maintain
compliance with RFC 1155."
::= { phivEndRemoteEntry 2 }
phivEndCircuitIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique index value for each known circuit used to
communicate with the remote node. This is the same
value as phivCircuitIndex."
::= { phivEndRemoteEntry 3 }
phivEndActiveLinks OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This read-only parameter represents the number of active
logical links from the executor to the destination node."
::= { phivEndRemoteEntry 4 }
phivEndDelay OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This read-only parameter is the average round trip
delay in seconds to the destination node. This
parameter is kept on a remote node basis."
::= { phivEndRemoteEntry 5 }
phivEndCountTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhivEndCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the counters associated with each end
system that is known to the entity. These counters
reflect totals from the perspective of the executor
node."
::= { end 2 }
phivEndCountEntry OBJECT-TYPE
SYNTAX PhivEndCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about a particular session between two end
systems."
INDEX { phivEndCountHostNodeID }
::= { phivEndCountTable 1 }
PhivEndCountEntry ::=
SEQUENCE {
phivEndCountHostNodeID
PhivAddr,
phivEndCountSecsLastZeroed
PhivCounter,
phivEndCountUsrBytesRec
PhivCounter,
phivEndCountUsrBytesSent
PhivCounter,
phivEndUCountUsrMessRec
PhivCounter,
phivEndCountUsrMessSent
PhivCounter,
phivEndCountTotalBytesRec
PhivCounter,
phivEndCountTotalBytesSent
PhivCounter,
phivEndCountTotalMessRec
PhivCounter,
phivEndCountTotalMessSent
PhivCounter,
phivEndCountConnectsRecd
PhivCounter,
phivEndCountConnectsSent
PhivCounter,
phivEndCountReponseTimeouts
PhivCounter,
phivEndCountRecdConnectResErrs
PhivCounter
}
phivEndCountHostNodeID OBJECT-TYPE
SYNTAX PhivAddr ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the address of the remote node to be
evaluated."
::= { phivEndCountEntry 1 }
phivEndCountSecsLastZeroed OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the number of seconds that have elapsed
since the counters for the node in this table row were
last set to zero. This counter is located in the
network management layer, but is returned with the
end system information which follows."
::= { phivEndCountEntry 2 }
phivEndCountUsrBytesRec OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of user bytes received from the target host."
::= { phivEndCountEntry 3 }
phivEndCountUsrBytesSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of user bytes sent to the target host."
::= { phivEndCountEntry 4 }
phivEndUCountUsrMessRec OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of user messages received from the target host."
::= { phivEndCountEntry 5 }
phivEndCountUsrMessSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of user messages sent to the target host."
::= { phivEndCountEntry 6 }
phivEndCountTotalBytesRec OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of bytes received from the target host."
::= { phivEndCountEntry 7 }
phivEndCountTotalBytesSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of bytes sent to the target host."
::= { phivEndCountEntry 8 }
phivEndCountTotalMessRec OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of messages received from the target host."
::= { phivEndCountEntry 9 }
phivEndCountTotalMessSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of messages sent to the target host."
::= { phivEndCountEntry 10 }
phivEndCountConnectsRecd OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of connects received from the target host."
::= { phivEndCountEntry 11 }
phivEndCountConnectsSent OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of connects sent to the target host."
::= {phivEndCountEntry 12 }
phivEndCountReponseTimeouts OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of response timeouts."
::= { phivEndCountEntry 13 }
phivEndCountRecdConnectResErrs OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of received connect resource errors."
::= {phivEndCountEntry 14 }
phivEndMaxLinks OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum active logical
link count allowed for the executor."
::= { end 3 }
phivEndNSPVers OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This read-only parameter represents the version number
of the node End Communication S/W. The format is
version number, ECO, and user ECO, e.g., 4.1.0"
::= { end 4 }
phivEndRetransmitFactor OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum number of times the
source End Communication at the executor node will
restart the retransmission timer when it expires. If
the number is exceeded, Session Control disconnects the
logical link for the user."
::= { end 5 }
phivEndDelayFact OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This is the number by which to multiply one sixteenth
of the estimated round trip delay to a node to set the
retransmission timer to that node."
::= { end 6 }
phivEndDelayWeight OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This number represents the weight to apply to a
current round trip delay estimate to a remote node
when updating the estimated round trip delay to a node.
On some systems the number must be 1 less than a power
of 2 for computational efficiency."
::= { end 7 }
phivEndInactivityTimer OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum duration of inactivity
(no data in either direction) on a logical link before
the node checks to see if the logical link still works.
If no activity occurs within the minimum number of
seconds, End Communication generates artificial
traffic to test the link (End Communication
specification)."
::= { end 8 }
phivEndCountZeroCount OBJECT-TYPE
SYNTAX INTEGER {
other (1),
reset (2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When this value is set to 2, all of the counters in
the End System Counter Table are set to zero."
::= { end 9 }
phivEndMaxLinksActive OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the high water mark for the
number of links that were active at any one time."
::= { end 10 }
phivRouteBroadcastRouteTimer OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value determines the maximum time in seconds
allowed between Routing updates on Ethernet
circuits. When this timer expired before a routing
update occurs, a routing update is forced. With a
standard calculation, Routing also uses this timer
to enforce a minimum delay between routing updates."
::= { routing 1 }
phivRouteBuffSize OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter value determines the maximum size of
a Routing message. It therefore determines the maximum
size message that can be forwarded. This size includes
protocol overhead down to and including the End
Communication layer, plus a constant value of 6. (This
value of 6 is included to provide compatibility with
the parameter definition in Phase III, which included
the Routing overhead.) It does not include Routing or
Data link overhead (except for the constant value of
6). There is one buffer size for all circuits.
NOTE: The BUFFER SIZE defines the maximum size messages
that the Routing layer can forward. The SEGMENT BUFFER
SIZE (defined below) defines the maximum size messages
that the End Communication layer can transmit or
receive. The SEGMENT BUFFER SIZE is always less than
or equal to the BUFFER SIZE. Normally the two
parameters will be equal. They may be different to
allow the network manager to alter buffer sizes
on all nodes without interruption of service. They both
include an extra 6 bytes for compatibility with Phase
III."
::= { routing 2 }
phivRouteRoutingVers OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This read-only parameter identifies the executor node's
Routing version number. The format is version number,
ECO, and user ECO, e.g., 4.1.0"
::= { routing 3 }
phivRouteMaxAddr OBJECT-TYPE
SYNTAX INTEGER (1..1023)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the largest node number and,
therefore, number of nodes that can be known about
by the executor node's home area."
::= { routing 4 }
phivRouteMaxBdcastNonRouters OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum total number of
nonrouters the executor node can have on its Ethernet
circuits."
::= { routing 5 }
phivRouteMaxBdcastRouters OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum total number of
routers the executor node can have on its Ethernet
circuits."
::= { routing 6 }
phivRouteMaxBuffs OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum number of transmit
buffers that Routing may use for all circuits."
::= { routing 7 }
phivRouteMaxCircuits OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum number of Routing
circuits that the executor node can know about."
::= { routing 8 }
phivRouteMaxCost OBJECT-TYPE
SYNTAX INTEGER (1..1022)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum total path cost
allowed from the executor to any node within an area.
The path cost is the sum of the circuit costs along
a path between two nodes. This parameter defines the
point where the executor node's Routing routing
decision algorithm declares another node unreachable
because the cost of the least costly path to the
other node is excessive. For correct operation, this
parameter must not be less than the maximum path cost
of the network."
::= { routing 9 }
phivRouteMaxHops OBJECT-TYPE
SYNTAX INTEGER (1..30)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum number of routing hops
allowable from the executor to any other reachable node
within an area. (A hop is the logical distance over a
circuit between two adjacent nodes.) This parameter
defines the point where the executor node's Routing
routing decision algorithm declares another node
unreachable because the length of the shortest path
between the two nodes is too long. For correct
operation, this parameter must not be less than the
network diameter. (The network diameter is the
reachability distance between the two nodes of the
network having the greatest reachability distance,
where reachability distance is the length the shortest
path between a given pair of nodes.)"
::= { routing 10 }
phivRouteMaxVisits OBJECT-TYPE
SYNTAX INTEGER (1..63)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the maximum number of nodes a
message coming into the executor node can have visited.
If the message is not for this node and the MAXIMUM
VISITS number is exceeded, the message is discarded.
The MAXIMUM VISITS parameter defines the point where
the packet lifetime control algorithm discards
a packet that has traversed too many nodes. For correct
operation, this parameter must not be less than the
maximum path length of the network. (The maximum path
length is the routing distance between the two nodes of
the network having the greatest routing distance, where
routing distance is the length of the least costly
path between a given pair of nodes.)"
::= { routing 11 }
phivRouteRoutingTimer OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value determines the maximum time in seconds
allowed between Routing updates on non-Ethernet
circuits. When this timer expires before a routing
update occurs, a routing update is forced."
::= { routing 12 }
phivRouteSegBuffSize OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter value determines the maximum size of an
end-to-end segment. The size is a decimal integer in
the range 1-65535. This size is in bytes. This size
includes protocol overhead down to and including the
End Communication layer, plus a constant value of 6.
(This value of 6 is included to provide compatibility
with the BUFFER SIZE parameter definition.) It does not
include Routing or Data link overhead (except for the
constant value of 6)."
::= { routing 13 }
phivRouteType OBJECT-TYPE
SYNTAX INTEGER {
routing-III (1),
nonrouting-III (2),
area (3),
routing-IV (4),
nonrouting-IV (5)
}
ACCESS read-only
STATUS obsolete
DESCRIPTION
"This parameter indicates the type of the executor
node. The node-type is one of the following:
routing-III
nonrouting-III
routing-IV
ronrouting-IV
area
A routing node has full routing capability. A
nonrouting node contains a subset of the Routing
routing modules. The III and IV indicate the DNA
phase of the node. Nonrouting nodes can deliver
and receive packets to and from any node, but cannot
route packets from other nodes through to other nodes.
An area node routes between areas. Refer to the Routing
specification for details.
For adjacent nodes, this is a read-only parameter that
indicates the type of the reachable adjacent node.
NOTE: The ROUTING-III and NONROUTING-III values are
incremented by one compared to the standard DECnet
values in order to maintain compliance with RFC 1155)"
::= { routing 14 }
phivRouteCountAgedPktLoss OBJECT-TYPE
SYNTAX PhivCounter (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of aged packet losses."
::= { routing 15 }
phivRouteCountNodeUnrPktLoss OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of node unreachable packet losses."
::= { routing 16 }
phivRouteCountOutRngePktLoss OBJECT-TYPE
SYNTAX PhivCounter (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of node out-of-range packet losses."
::= { routing 17 }
phivRouteCountOverSzePktLoss OBJECT-TYPE
SYNTAX PhivCounter (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of Oversized packet losses."
::= { routing 18 }
phivRouteCountPacketFmtErr OBJECT-TYPE
SYNTAX PhivCounter (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of packet format errors."
::= { routing 19 }
phivRouteCountPtlRteUpdtLoss OBJECT-TYPE
SYNTAX PhivCounter (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of partial routing update losses."
::= { routing 20 }
phivRouteCountVerifReject OBJECT-TYPE
SYNTAX PhivCounter (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of verification rejects."
::= { routing 21 }
phivLevel1RouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhivLevel1RouteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the currently known DECnet Phase
IV Routes."
::= { routing 22 }
phivLevel1RouteEntry OBJECT-TYPE
SYNTAX PhivLevel1RouteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the currently known DECnet Phase
IV Routes."
INDEX { phivLevel1RouteNodeAddr }
::= { phivLevel1RouteTable 1 }
PhivLevel1RouteEntry ::=
SEQUENCE {
phivLevel1RouteNodeAddr
PhivAddr,
phivLevel1RouteCircuitIndex
INTEGER,
phivLevel1RouteCost
INTEGER,
phivLevel1RouteHops
INTEGER,
phivLevel1RouteNextNode
PhivAddr
}
phivLevel1RouteNodeAddr OBJECT-TYPE
SYNTAX PhivAddr ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the address of the node about which
routing information is contained in this level 1
routing table."
::= { phivLevel1RouteEntry 1 }
phivLevel1RouteCircuitIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique index value for each known circuit. This is
the index to the circuit state table and is the same
value as phivCircuitIndex."
::= { phivLevel1RouteEntry 2 }
phivLevel1RouteCost OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This read-only parameter represents the total cost
over the current path to the destination node. Cost is
a positive integer value associated with using a
circuit. Routing routes messages (data) along the path
between two nodes with the smallest cost. COST is kept
on a remote node basis."
::= { phivLevel1RouteEntry 3 }
phivLevel1RouteHops OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This read-only parameter represents the number of hops
over to a destination node. A hop is Routing value
representing the logical distance between two nodes in
a network. HOPS is kept on a remote node basis."
::= { phivLevel1RouteEntry 4 }
phivLevel1RouteNextNode OBJECT-TYPE
SYNTAX PhivAddr ACCESS read-only
STATUS mandatory
DESCRIPTION
"This read-only value indicates the next node on the
circuit used to get to the node under scrutiny
(next hop)."
::= { phivLevel1RouteEntry 5 }
phivRouteCountZeroCount OBJECT-TYPE
SYNTAX INTEGER {
other (1),
reset (2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When this value is set to 2, the following objects are
set to Zero: phivRouteCountAgedPktLoss,
phivRouteCountNodeUnrPktLoss,
phivRouteCountOutRngePktLoss,
phivRouteCountOverSzePktLoss,
phivRouteCountPacketFmtErr,
phivRouteCountPtlRteUpdtLoss, and
phivRouteCountVerifReject."
::= { routing 23 }
phivRouteSystemAddr OBJECT-TYPE
SYNTAX PhivAddr ACCESS read-only
STATUS obsolete
DESCRIPTION
"DECnet Phase IV node address."
::= { routing 24 }
phivRouteRoutingType OBJECT-TYPE
SYNTAX INTEGER {
routing-III (1),
nonrouting-III (2),
area (3),
routing-IV (4),
nonrouting-IV (5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This read-write parameter indicates the type of the executor
node. The node-type is one of the following:
routing-III
nonrouting-III
routing-IV
ronrouting-IV
area
A routing node has full routing capability. A
nonrouting node contains a subset of the Routing
routing modules. The III and IV indicate the DNA
phase of the node. Nonrouting nodes can deliver
and receive packets to and from any node, but cannot
route packets from other nodes through to other nodes.
An area node routes between areas. Refer to the Routing
specification for details.
For adjacent nodes, this is a read-only parameter that
indicates the type of the reachable adjacent node.
NOTE: The ROUTING-III and NONROUTING-III values are
incremented by one compared to the standard DECnet
values in order to maintain compliance with RFC 1155)"
::= { routing 25 }
phivRouteSystemAddress OBJECT-TYPE
SYNTAX PhivAddr ACCESS read-write
STATUS mandatory
DESCRIPTION
"DECnet Phase IV node address."
::= { routing 26 }
phivCircuitParametersTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhivCircuitParametersEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the parameters associated with all
circuits currently known."
::= {circuit 1 }
phivCircuitParametersEntry OBJECT-TYPE
SYNTAX PhivCircuitParametersEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Parameters information about all circuits currently
known."
INDEX { phivCircuitIndex }
::= { phivCircuitParametersTable 1 }
PhivCircuitParametersEntry ::=
SEQUENCE {
phivCircuitIndex
INTEGER,
phivCircuitLineIndex
INTEGER,
phivCircuitCommonState
INTEGER,
phivCircuitCommonSubState
INTEGER,
phivCircuitCommonName
DisplayString,
phivCircuitExecRecallTimer
INTEGER,
phivCircuitCommonType
INTEGER,
phivCircuitService
INTEGER,
phivCircuitExecCost
INTEGER,
phivCircuitExecHelloTimer
INTEGER
}
phivCircuitIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique index value for each known circuit."
::= { phivCircuitParametersEntry 1 }
phivCircuitLineIndex OBJECT-TYPE
SYNTAX InterfaceIndex
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The line on which this circuit is active. This is
the same as the ifIndex."
::= { phivCircuitParametersEntry 2 }
phivCircuitCommonState OBJECT-TYPE
SYNTAX INTEGER {
on (1),
off (2),
service (3),
cleared (4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the circuit's Network Management
operational state. NOTE: These values are incremented
by one compared to the standard DECnet values in order
to maintain compliance with RFC 1155."
::= { phivCircuitParametersEntry 3 }
phivCircuitCommonSubState OBJECT-TYPE
SYNTAX INTEGER {
starting (1),
reflecting (2),
looping (3),
loading (4),
dumping (5),
triggering (6),
autoservice (7),
autoloading (8),
autodumping (9),
autotriggering (10),
synchronizing (11),
failed (12),
running (13)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value represents the circuit's Network Management
operational and service substate. NOTE: These values are
incremented by one compared to the standard DECnet values
in order to maintain compliance with RFC 1155."
::= { phivCircuitParametersEntry 4 }
phivCircuitCommonName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of the circuit entry in the table, for example,
SVA-0 or in a level 2 router ASYNC-8 or ETHER-1)."
::= { phivCircuitParametersEntry 5 }
phivCircuitExecRecallTimer OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter represents the minimum number of
seconds to wait before restarting the circuit. A
value of 0 indicates not timer is running."
::= { phivCircuitParametersEntry 6 }
phivCircuitCommonType OBJECT-TYPE
SYNTAX INTEGER {
ddcmp-point (1),
ddcmp-control (2),
ddcmp-tributary (3),
x25 (4),
ddcmp-dmc (5),
ethernet (6),
ci (7),
qp2-dte20 (8),
bisync (9),
other (14),
fddi (15)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Represents the type of the circuit. For X.25 circuits,
the value must be set to X25. For DDCMP and Ethernet
circuits it is read only and is the same value as the
protocol of the associated line.
NOTE: Values 1 - 5 are incremented by one compared to the
standard DECnet values in order to maintain compliance
with RFC 1155."
::= { phivCircuitParametersEntry 7 }
phivCircuitService OBJECT-TYPE
SYNTAX INTEGER {
enabled (1),
disabled (2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value indicates whether or not Network Management
allows service operations on a circuit. The values for
service-control are as follows:
ENABLED SERVICE state and/or service functions are
allowed.
DISABLED SERVICE state and/or service functions are not
allowed.
NOTE: These values are incremented by one compared to the
standard DECnet values in order to maintain compliance
with RFC 1155."
::= { phivCircuitParametersEntry 8 }
phivCircuitExecCost OBJECT-TYPE
SYNTAX INTEGER (1..25)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value represents the routing cost of the circuit.
Routing sends messages along the path between two nodes
having the smallest cost."
::= { phivCircuitParametersEntry 9 }
phivCircuitExecHelloTimer OBJECT-TYPE
SYNTAX INTEGER (1..8191)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value determines the frequency of Routing Hello
messages sent to the adjacent node on the circuit."
::= { phivCircuitParametersEntry 10 }
phivCircuitCountTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhivCircuitCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the counters associated with all
circuits currently known."
::= { circuit 2 }
phivCircuitCountEntry OBJECT-TYPE
SYNTAX PhivCircuitCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Counter information about all circuits currently known"
INDEX { phivCircuitIndex }
::= { phivCircuitCountTable 1 }
PhivCircuitCountEntry ::=
SEQUENCE {
phivCircuitCountSecLastZeroed
PhivCounter,
phivCircuitCountTermPacketsRecd
PhivCounter,
phivCircuitCountOriginPackSent
PhivCounter,
phivCircuitCountTermCongLoss
PhivCounter,
phivCircuitCountCorruptLoss
PhivCounter,
phivCircuitCountTransitPksRecd
PhivCounter,
phivCircuitCountTransitPkSent
PhivCounter,
phivCircuitCountTransitCongestLoss
PhivCounter,
phivCircuitCountCircuitDown
PhivCounter,
phivCircuitCountInitFailure
PhivCounter,
phivCircuitCountAdjDown
PhivCounter,
phivCircuitCountPeakAdj
PhivCounter,
phivCircuitCountBytesRecd
PhivCounter,
phivCircuitCountBytesSent
PhivCounter,
phivCircuitCountDataBlocksRecd
PhivCounter,
phivCircuitCountDataBlocksSent
PhivCounter,
phivCircuitCountUsrBuffUnav
PhivCounter
}
phivCircuitCountSecLastZeroed OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of seconds since the circuit counters for this
circuit were last zeroed."
::= { phivCircuitCountEntry 1 }
phivCircuitCountTermPacketsRecd OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of terminating packets received on this circuit."
::= { phivCircuitCountEntry 2 }
phivCircuitCountOriginPackSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of originating packets sent on this circuit."
::= { phivCircuitCountEntry 3 }
phivCircuitCountTermCongLoss OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of terminating congestion losses on this
circuit."
::= { phivCircuitCountEntry 4 }
phivCircuitCountCorruptLoss OBJECT-TYPE
SYNTAX PhivCounter (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of corruption losses on this circuit."
::= { phivCircuitCountEntry 5 }
phivCircuitCountTransitPksRecd OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of Transit packets received on this circuit."
::= { phivCircuitCountEntry 6 }
phivCircuitCountTransitPkSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of transit packets sent on this circuit."
::= { phivCircuitCountEntry 7 }
phivCircuitCountTransitCongestLoss OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of transit congestion losses on this circuit."
::= { phivCircuitCountEntry 8 }
phivCircuitCountCircuitDown OBJECT-TYPE
SYNTAX PhivCounter (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of circuit downs on this circuit."
::= { phivCircuitCountEntry 9 }
phivCircuitCountInitFailure OBJECT-TYPE
SYNTAX PhivCounter (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of Initialization failures on this circuit."
::= { phivCircuitCountEntry 10 }
phivCircuitCountAdjDown OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This counter indicates the number of adjacency losses
that result from any of the following:
Node listener timeout
Invalid data received at node listener
Unexpected control (initialization or verification)
message received
Routing message received with a checksum error
Node identification from a routing message or a
Hello message that is not the one expected Hello
message received indicating that connectivity
became one-way
Adjacency idled."
::= { phivCircuitCountEntry 11 }
phivCircuitCountPeakAdj OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This counter indicates the maximum number of nodes
that are up on the circuit."
::= { phivCircuitCountEntry 12 }
phivCircuitCountBytesRecd OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of bytes received on this circuit."
::= { phivCircuitCountEntry 13 }
phivCircuitCountBytesSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of bytes sent on this circuit."
::= { phivCircuitCountEntry 14 }
phivCircuitCountDataBlocksRecd OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of data blocks received on this circuit."
::= { phivCircuitCountEntry 15 }
phivCircuitCountDataBlocksSent OBJECT-TYPE
SYNTAX PhivCounter (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of data blocks sent on this circuit."
::= { phivCircuitCountEntry 16 }
phivCircuitCountUsrBuffUnav OBJECT-TYPE
SYNTAX PhivCounter (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of user buffer unavailable errors."
::= { phivCircuitCountEntry 17 }
phivCircuitOrigQueueLimit OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter indicates the maximum number of
originating packets that may be outstanding on this
circuit. This does not include route-thru traffic."
::= { circuit 3 }
phivCircuitCountZeroCount OBJECT-TYPE
SYNTAX INTEGER {
other (1),
reset (2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When this value is set to 2, all of the counters in the
Circuit Counter Table are set to zero."
::= { circuit 4 }
phivDDCMPCircuitParametersTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhivDDCMPCircuitParametersEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about DDCMP circuit parameters."
::= { ddcmp 1}
phivDDCMPCircuitParametersEntry OBJECT-TYPE
SYNTAX PhivDDCMPCircuitParametersEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Parameters information about DDCMP circuits currently
known."
INDEX { phivDDCMPCircuitIndex }
::= { phivDDCMPCircuitParametersTable 1 }
PhivDDCMPCircuitParametersEntry ::=
SEQUENCE {
phivDDCMPCircuitIndex
INTEGER,
phivDDCMPCircuitAdjNodeAddr
INTEGER,
phivDDCMPCircuitTributary
INTEGER
}
phivDDCMPCircuitIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique index value for each known DDCMP circuit.
This is the same value as phivCircuitIndex."
::= { phivDDCMPCircuitParametersEntry 1 }
phivDDCMPCircuitAdjNodeAddr OBJECT-TYPE
SYNTAX PhivAddr ACCESS read-only
STATUS mandatory
DESCRIPTION
"The address of the adjacent node."
::= { phivDDCMPCircuitParametersEntry 2 }
phivDDCMPCircuitTributary OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value represents the Data Link physical tributary
address of the circuit."
::= { phivDDCMPCircuitParametersEntry 3 }
phivDDCMPCircuitCountTable OBJECT-TYPE
SYNTAX SEQUENCE OF PhivDDCMPCircuitCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the DDCMP counters associated with all
circuits currently known."
::= { ddcmp 2 }
phivDDCMPCircuitCountEntry OBJECT-TYPE
SYNTAX PhivDDCMPCircuitCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Counter information about DDCMP circuits now known"
INDEX { phivCircuitIndex }
::= { phivDDCMPCircuitCountTable 1 }
PhivDDCMPCircuitCountEntry ::=
SEQUENCE {
phivDDCMPCircuitErrorsInbd
PhivCounter,
phivDDCMPCircuitErrorsOutbd
PhivCounter,
phivDDCMPCircuitRmteReplyTimeouts
PhivCounter,
phivDDCMPCircuitLocalReplyTimeouts
PhivCounter,
phivDDCMPCircuitRmteBuffErrors
PhivCounter,
phivDDCMPCircuitLocalBuffErrors
PhivCounter,
phivDDCMPCircuitSelectIntervalsElap
PhivCounter,
phivDDCMPCircuitSelectTimeouts
PhivCounter
}
phivDDCMPCircuitErrorsInbd OBJECT-TYPE
SYNTAX PhivCounter (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of Data errors inbound."
::= { phivDDCMPCircuitCountEntry 1 }
phivDDCMPCircuitErrorsOutbd OBJECT-TYPE
SYNTAX PhivCounter (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of outbound data errors."
::= { phivDDCMPCircuitCountEntry 2 }
phivDDCMPCircuitRmteReplyTimeouts OBJECT-TYPE
SYNTAX PhivCounter (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of remote reply timeouts."
::= { phivDDCMPCircuitCountEntry