VDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Gauge32,
Integer32,
Unsigned32,
NOTIFICATION-TYPE,
transmission FROM SNMPv2-SMI ZeroBasedCounter64 FROM HCNUM-TC TEXTUAL-CONVENTION,
RowStatus,
TruthValue FROM SNMPv2-TC HCPerfValidIntervals,
HCPerfInvalidIntervals,
HCPerfTimeElapsed,
HCPerfIntervalThreshold,
HCPerfCurrentCount,
HCPerfIntervalCount FROM HC-PerfHist-TC-MIB MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB; vdslMIB MODULE-IDENTITY
LAST-UPDATED "200402190000Z" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Sand Channel Systems
Postal: P.O. Box 37324
Raleigh, NC 27627-7324
USA
Email: sneedmike@hotmail.com
Phone: +1 206 600 7022
Co-editor: Bob Ray
PESA Switching Systems, Inc.
Postal: 330-A Wynn Drive
Huntsville, AL 35805
USA
Email: rray@pesa.com
Phone: +1 256 726 9200 ext. 142
Co-editor: Rajesh Abbi
Alcatel USA
Postal: 2301 Sugar Bush Road
Raleigh, NC 27612-3339
USA
Email: Rajesh.Abbi@alcatel.com
Phone: +1 919 850 6194
"
DESCRIPTION
"The MIB module defining objects for the management of a pair
of VDSL transceivers at each end of the VDSL line. Each such
line has an entry in an ifTable which may include multiple
transceiver lines. An agent may reside at either end of the
VDSL line. However, the MIB is designed to require no
management communication between them beyond that inherent in
the low-level VDSL line protocol. The agent may monitor and
control this protocol for its needs.
VDSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus a VDSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to vdsl(97), fast(125), and
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.
Naming Conventions:
Vtuc -- (VTUC) transceiver at near (Central) end of line
Vtur -- (VTUR) transceiver at Remote end of line
Vtu -- One of either Vtuc or Vtur
Curr -- Current
Prev -- Previous
Atn -- Attenuation
ES -- Errored Second.
SES -- Severely Errored Second
UAS -- Unavailable Second
LCS -- Line Code Specific
Lof -- Loss of Frame
Lol -- Loss of Link
Los -- Loss of Signal
Lpr -- Loss of Power
xxxs -- Sum of Seconds in which xxx has occured
(e.g., xxx = Lof, Los, Lpr, Lol)
Max -- Maximum
Mgn -- Margin
Min -- Minimum
Psd -- Power Spectral Density
Snr -- Signal to Noise Ratio
Tx -- Transmit
Blks -- Blocks
Copyright (C) The Internet Society (2004). This version
of this MIB module is part of RFC 3728: see the RFC
itself for full legal notices."
REVISION "200402190000Z" DESCRIPTION "Initial version, published as RFC 3728."
::= { transmission 97 }
vdslLineMib OBJECT IDENTIFIER ::= { vdslMIB 1 }
vdslMibObjects OBJECT IDENTIFIER ::= { vdslLineMib 1 }
VdslLineCodingType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This data type is used as the syntax for the VDSL Line
Code. Attributes with this syntax identify the line coding
used. Specified as an INTEGER, the three values are:
other(1) -- none of the following
mcm(2) -- Multiple Carrier Modulation
scm(3) -- Single Carrier Modulation"
SYNTAX INTEGER
{
other(1),
mcm(2),
scm(3)
}
VdslLineEntity ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a transceiver as being either Vtuc or Vtur.
A VDSL line consists of two transceivers, a Vtuc and a
Vtur. Attributes with this syntax reference the two sides
of a line. Specified as an INTEGER, the two values are:
vtuc(1) -- central site transceiver
vtur(2) -- remote site transceiver"
SYNTAX INTEGER
{
vtuc(1),
vtur(2)
}
vdslLineTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes common attributes describing
both ends of the line. It is required for all VDSL
physical interfaces. VDSL physical interfaces are
those ifEntries where ifType is equal to vdsl(97)."
::= { vdslMibObjects 1 }
vdslLineEntry OBJECT-TYPE
SYNTAX VdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the vdslLineTable."
INDEX { ifIndex }
::= { vdslLineTable 1 }
VdslLineEntry ::=
SEQUENCE
{
vdslLineCoding VdslLineCodingType,
vdslLineType INTEGER,
vdslLineConfProfile SnmpAdminString,
vdslLineAlarmConfProfile SnmpAdminString
}
vdslLineCoding OBJECT-TYPE
SYNTAX VdslLineCodingType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the VDSL coding type used on this line."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslLineEntry 1 }
vdslLineType OBJECT-TYPE
SYNTAX INTEGER
{
noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defines the type of VDSL physical line entity that exists,
by defining whether and how the line is channelized. If
the line is channelized, the value will be other than
noChannel(1). This object defines which channel type(s)
are supported. Defined values are:
noChannel(1) -- no channels exist
fastOnly(2) -- only fast channel exists
interleavedOnly(3) -- only interleaved channel exists
fastOrInterleaved(4) -- either fast or interleaved channel
-- exist, but only one at a time
fastAndInterleaved(5) -- both fast and interleaved channels
-- exist
Note that 'slow' and 'interleaved' refer to the same
channel. In the case that the line is channelized, the
manager can use the ifStackTable to determine the ifIndex
for the associated channel(s)."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslLineEntry 2 }
vdslLineConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the VDSL
Line Configuration Profile Table, vdslLineConfProfileTable,
which applies for this VDSL line, and channels if
applicable.
This object MUST be maintained in a persistent manner."
DEFVAL { "DEFVAL" }
::= { vdslLineEntry 3 }
vdslLineAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the VDSL
Line Alarm Configuration Profile Table,
vdslLineAlarmConfProfileTable, which applies to this
VDSL line, and channels if applicable.
This object MUST be maintained in a persistent manner."
DEFVAL { "DEFVAL" }
::= { vdslLineEntry 4 }
vdslPhysTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu. Each row
contains the Physical Layer Parameters table for that
Vtu. VDSL physical interfaces are those ifEntries where
ifType is equal to vdsl(97)."
::= { vdslMibObjects 2 }
vdslPhysEntry OBJECT-TYPE
SYNTAX VdslPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the vdslPhysTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslPhysTable 1 }
VdslPhysEntry ::=
SEQUENCE
{
vdslPhysSide VdslLineEntity,
vdslPhysInvSerialNumber SnmpAdminString,
vdslPhysInvVendorID SnmpAdminString,
vdslPhysInvVersionNumber SnmpAdminString,
vdslPhysCurrSnrMgn Integer32,
vdslPhysCurrAtn Gauge32,
vdslPhysCurrStatus BITS,
vdslPhysCurrOutputPwr Integer32,
vdslPhysCurrAttainableRate Gauge32,
vdslPhysCurrLineRate Gauge32
}
vdslPhysSide OBJECT-TYPE
SYNTAX VdslLineEntity
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identifies whether the transceiver is the Vtuc or Vtur."
::= { vdslPhysEntry 1 }
vdslPhysInvSerialNumber OBJECT-TYPE
SYNTAX SnmpAdminString(SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific string that identifies the
vendor equipment."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 2 }
vdslPhysInvVendorID OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor ID code is a copy of the binary vendor
identification field expressed as readable characters
in hexadecimal notation."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 3 }
vdslPhysInvVersionNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific version number sent by this Vtu
as part of the initialization messages. It is a copy
of the binary version number field expressed as
readable characters in hexadecimal notation."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 4 }
vdslPhysCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32 (-127..127)
UNITS "0.25dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Noise Margin as seen by this Vtu with respect to its
received signal in 0.25dB. The effective range is
-31.75 to +31.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 5 }
vdslPhysCurrAtn OBJECT-TYPE
SYNTAX Gauge32 (0..255)
UNITS "0.25dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured difference in the total power transmitted by
the peer Vtu and the total power received by this Vtu.
The effective range is 0 to +63.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 6 }
vdslPhysCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
lossOfFraming(1),
lossOfSignal(2),
lossOfPower(3),
lossOfSignalQuality(4),
lossOfLink(5),
dataInitFailure(6),
configInitFailure(7),
protocolInitFailure(8),
noPeerVtuPresent(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There are no defects on the line.
1 lossOfFraming Vtu failure due to not receiving
a valid frame.
2 lossOfSignal Vtu failure due to not receiving
signal.
3 lossOfPower Vtu failure due to loss of power.
4 lossOfSignalQuality Loss of Signal Quality is declared
when the Noise Margin falls below
the Minimum Noise Margin, or the
bit-error-rate exceeds 10^-7.
5 lossOfLink Vtu failure due to inability to
link with peer Vtu. Set whenever
the transceiver is in the 'Warm
Start' state.
6 dataInitFailure Vtu failure during initialization
due to bit errors corrupting
startup exchange data.
7 configInitFailure Vtu failure during initialization
due to peer Vtu not able to
support requested configuration.
8 protocolInitFailure Vtu failure during initialization
due to incompatible protocol used
by the peer Vtu.
9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence
detected from peer Vtu.
This is intended to supplement ifOperStatus."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 7 }
vdslPhysCurrOutputPwr OBJECT-TYPE
SYNTAX Integer32 (0..160)
UNITS "0.1dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured total output power transmitted by this VTU.
This is the measurement that was reported during
the last activation sequence."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 8 }
vdslPhysCurrAttainableRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kbps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the maximum currently attainable data rate
in steps of 1000 bits/second by the Vtu. This value
will be equal to or greater than vdslPhysCurrLineRate.
Note that for SCM, the minimum and maximum data rates
are equal. Note: 1 kbps = 1000 bps."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 9 }
vdslPhysCurrLineRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kbps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current data rate in steps of 1000
bits/second by the Vtu. This value will be less than
or equal to vdslPhysCurrAttainableRate. Note: 1 kbps =
1000 bps."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 10 }
vdslChanTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu channel.
VDSL channel interfaces are those ifEntries where
ifType is equal to interleave(124) or fast(125)."
::= { vdslMibObjects 3 }
vdslChanEntry OBJECT-TYPE
SYNTAX VdslChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslChanTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslChanTable 1 }
VdslChanEntry ::=
SEQUENCE
{
vdslChanInterleaveDelay Gauge32,
vdslChanCrcBlockLength Gauge32,
vdslChanCurrTxRate Gauge32,
vdslChanCurrTxSlowBurstProtect Gauge32,
vdslChanCurrTxFastFec Gauge32
}
vdslChanInterleaveDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interleave Delay for this channel.
Interleave delay applies only to the interleave
(slow) channel and defines the mapping (relative
spacing) between subsequent input bytes at the
interleaver input and their placement in the bit
stream at the interleaver output. Larger numbers
provide greater separation between consecutive
input bytes in the output bit stream allowing for
improved impulse noise immunity at the expense of
payload latency.
In the case where the ifType is fast(125), return
a value of zero."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanEntry 1 }
vdslChanCrcBlockLength OBJECT-TYPE
SYNTAX Gauge32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the length of the channel data-block
on which the CRC operates."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanEntry 2 }
vdslChanCurrTxRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kbps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual transmit data rate on this channel. Note: 1
kbps = 1000 bps."
::= { vdslChanEntry 3 }
vdslChanCurrTxSlowBurstProtect OBJECT-TYPE
SYNTAX Gauge32 (0..1275)
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual level of impulse noise (burst) protection
for an interleaved (slow) channel. This parameter is
not applicable to fast channels. For fast channels,
a value of zero shall be returned."
REFERENCE "ITU-T G.997.1, section 7.3.2.3"
::= { vdslChanEntry 4 }
vdslChanCurrTxFastFec OBJECT-TYPE
SYNTAX Gauge32 (0..50)
UNITS "%"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Forward Error Correction (FEC) redundancy
related overhead for a fast channel. This parameter
is not applicable to an interleaved (slow) channel.
For interleaved channels, a value of zero shall be
returned."
::= { vdslChanEntry 5 }
vdslPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each VDSL physical
interface. VDSL physical interfaces are those ifEntries
where ifType is equal to vdsl(97)."
::= { vdslMibObjects 4 }
vdslPerfDataEntry OBJECT-TYPE
SYNTAX VdslPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslPerfDataTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslPerfDataTable 1 }
VdslPerfDataEntry ::=
SEQUENCE
{
vdslPerfDataValidIntervals HCPerfValidIntervals,
vdslPerfDataInvalidIntervals HCPerfInvalidIntervals,
vdslPerfDataLofs Unsigned32,
vdslPerfDataLoss Unsigned32,
vdslPerfDataLprs Unsigned32,
vdslPerfDataLols Unsigned32,
vdslPerfDataESs Unsigned32,
vdslPerfDataSESs Unsigned32,
vdslPerfDataUASs Unsigned32,
vdslPerfDataInits Unsigned32,
vdslPerfDataCurr15MinTimeElapsed HCPerfTimeElapsed,
vdslPerfDataCurr15MinLofs HCPerfCurrentCount,
vdslPerfDataCurr15MinLoss HCPerfCurrentCount,
vdslPerfDataCurr15MinLprs HCPerfCurrentCount,
vdslPerfDataCurr15MinLols HCPerfCurrentCount,
vdslPerfDataCurr15MinESs HCPerfCurrentCount,
vdslPerfDataCurr15MinSESs HCPerfCurrentCount,
vdslPerfDataCurr15MinUASs HCPerfCurrentCount,
vdslPerfDataCurr15MinInits HCPerfCurrentCount,
vdslPerfData1DayValidIntervals HCPerfValidIntervals,
vdslPerfData1DayInvalidIntervals HCPerfInvalidIntervals,
vdslPerfDataCurr1DayTimeElapsed HCPerfTimeElapsed,
vdslPerfDataCurr1DayLofs Unsigned32,
vdslPerfDataCurr1DayLoss Unsigned32,
vdslPerfDataCurr1DayLprs Unsigned32,
vdslPerfDataCurr1DayLols Unsigned32,
vdslPerfDataCurr1DayESs Unsigned32,
vdslPerfDataCurr1DaySESs Unsigned32,
vdslPerfDataCurr1DayUASs Unsigned32,
vdslPerfDataCurr1DayInits Unsigned32
}
vdslPerfDataValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 1 }
vdslPerfDataInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 2 }
vdslPerfDataLofs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Framing."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 3 }
vdslPerfDataLoss OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Signal."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 4 }
vdslPerfDataLprs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Power."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 5 }
vdslPerfDataLols OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Link."
::= { vdslPerfDataEntry 6 }
vdslPerfDataESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds since the unit was last reset.
An Errored Second is a one-second interval containing one
or more CRC anomalies, or one or more LOS or LOF defects."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 7 }
vdslPerfDataSESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds since the unit was last
reset."
::= { vdslPerfDataEntry 8 }
vdslPerfDataUASs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds since the unit was last
reset."
::= { vdslPerfDataEntry 9 }
vdslPerfDataInits OBJECT-TYPE
SYNTAX Unsigned32
UNITS "occurrences"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts since the unit
was last reset. This count includes both successful and
failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 10 }
vdslPerfDataCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { vdslPerfDataEntry 11 }
vdslPerfDataCurr15MinLofs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there
was Loss of Framing."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 12 }
vdslPerfDataCurr15MinLoss OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there
was Loss of Signal."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 13 }
vdslPerfDataCurr15MinLprs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there
was Loss of Power."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 14 }
vdslPerfDataCurr15MinLols OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there
was Loss of Link."
::= { vdslPerfDataEntry 15 }
vdslPerfDataCurr15MinESs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds during this interval. An Errored
Second is a one-second interval containing one or more CRC
anomalies, or one or more LOS or LOF defects."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 16 }
vdslPerfDataCurr15MinSESs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds during this interval."
::= { vdslPerfDataEntry 17 }
vdslPerfDataCurr15MinUASs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds during this interval."
::= { vdslPerfDataEntry 18 }
vdslPerfDataCurr15MinInits OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "occurrences"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts during this
interval. This count includes both successful and
failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 19 }
vdslPerfData1DayValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 20 }
vdslPerfData1DayInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 21 }
vdslPerfDataCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 22 }
vdslPerfDataCurr1DayLofs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Framing (LOF) Seconds since the
beginning of the current 1-day interval."
::= { vdslPerfDataEntry 23 }
vdslPerfDataCurr1DayLoss OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Signal (LOS) Seconds since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 24 }
vdslPerfDataCurr1DayLprs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Power (LPR) Seconds since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 25 }
vdslPerfDataCurr1DayLols OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Link (LOL) Seconds since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 26 }
vdslPerfDataCurr1DayESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 27 }
vdslPerfDataCurr1DaySESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) since the
beginning of the current 1-day interval."
::= { vdslPerfDataEntry 28 }
vdslPerfDataCurr1DayUASs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 29 }
vdslPerfDataCurr1DayInits OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts since the
beginning of the current 1-day interval. This count
includes both successful and failed attempts."
::= { vdslPerfDataEntry 30 }
vdslPerfIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu performance
data collection interval. VDSL physical interfaces are
those ifEntries where ifType is equal to vdsl(97)."
::= { vdslMibObjects 5 }
vdslPerfIntervalEntry OBJECT-TYPE
SYNTAX VdslPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslPerfIntervalTable."
INDEX { ifIndex,
vdslPhysSide,
vdslPerfIntervalNumber }
::= { vdslPerfIntervalTable 1 }
VdslPerfIntervalEntry ::=
SEQUENCE
{
vdslPerfIntervalNumber Unsigned32,
vdslPerfIntervalLofs HCPerfIntervalCount,
vdslPerfIntervalLoss HCPerfIntervalCount,
vdslPerfIntervalLprs HCPerfIntervalCount,
vdslPerfIntervalLols HCPerfIntervalCount,
vdslPerfIntervalESs HCPerfIntervalCount,
vdslPerfIntervalSESs HCPerfIntervalCount,
vdslPerfIntervalUASs HCPerfIntervalCount,
vdslPerfIntervalInits HCPerfIntervalCount
}
vdslPerfIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number 1 is the most recent
previous interval; interval 96 is 24 hours ago.
Intervals 2 to 96 are optional."
::= { vdslPerfIntervalEntry 1 }
vdslPerfIntervalLofs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Framing."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 2 }
vdslPerfIntervalLoss OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Signal."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 3 }
vdslPerfIntervalLprs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Power."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 4 }
vdslPerfIntervalLols OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Link."
::= { vdslPerfIntervalEntry 5 }
vdslPerfIntervalESs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the interval. An Errored
Second is a one-second interval containing one or more CRC
anomalies, one or more LOS or LOF defects."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 6 }
vdslPerfIntervalSESs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds in the interval."
::= { vdslPerfIntervalEntry 7 }
vdslPerfIntervalUASs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds in the interval."
::= { vdslPerfIntervalEntry 8 }
vdslPerfIntervalInits OBJECT-TYPE
SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts during this
interval. This count includes both successful and
failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 9 }
vdslPerf1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each VDSL performance
data collection interval. This table contains live data
from equipment. As such, it is NOT persistent."
::= { vdslMibObjects 6 }
vdslPerf1DayIntervalEntry OBJECT-TYPE
SYNTAX VdslPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslPerf1DayIntervalTable."
INDEX { ifIndex,
vdslPhysSide,
vdslPerf1DayIntervalNumber }
::= { vdslPerf1DayIntervalTable 1 }
VdslPerf1DayIntervalEntry ::=
SEQUENCE
{
vdslPerf1DayIntervalNumber Unsigned32,
vdslPerf1DayIntervalMoniSecs HCPerfTimeElapsed,
vdslPerf1DayIntervalLofs Unsigned32,
vdslPerf1DayIntervalLoss Unsigned32,
vdslPerf1DayIntervalLprs Unsigned32,
vdslPerf1DayIntervalLols Unsigned32,
vdslPerf1DayIntervalESs Unsigned32,
vdslPerf1DayIntervalSESs Unsigned32,
vdslPerf1DayIntervalUASs Unsigned32,
vdslPerf1DayIntervalInits Unsigned32
}
vdslPerf1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the most
recent previous day; interval 30 is 30 days ago. Intervals
2 to 30 are optional."
::= { vdslPerf1DayIntervalEntry 1 }
vdslPerf1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { vdslPerf1DayIntervalEntry 2 }
vdslPerf1DayIntervalLofs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Frame (LOF) Seconds during the 1-day
interval as measured by vdslPerf1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerf1DayIntervalEntry 3 }
vdslPerf1DayIntervalLoss OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Signal (LOS) Seconds during the 1-day
interval as measured by vdslPerf1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerf1DayIntervalEntry 4 }
vdslPerf1DayIntervalLprs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Power (LPR) Seconds during the 1-day
interval as measured by vdslPerf1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerf1DayIntervalEntry 5 }
vdslPerf1DayIntervalLols OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Link (LOL) Seconds during the 1-day
interval as measured by vdslPerf1DayIntervalMoniSecs."
::= { vdslPerf1DayIntervalEntry 6 }
vdslPerf1DayIntervalESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day
interval as measured by vdslPerf1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerf1DayIntervalEntry 7 }
vdslPerf1DayIntervalSESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by vdslPerf1DayIntervalMoniSecs."
::= { vdslPerf1DayIntervalEntry 8 }
vdslPerf1DayIntervalUASs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day
interval as measured by vdslPerf1DayIntervalMoniSecs."
::= { vdslPerf1DayIntervalEntry 9 }
vdslPerf1DayIntervalInits OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts during the
1-day interval as measured by vdslPerf1DayIntervalMoniSecs.
This count includes both successful and failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerf1DayIntervalEntry 10 }
vdslChanPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu channel.
VDSL channel interfaces are those ifEntries where
ifType is equal to interleave(124) or fast(125)."
::= { vdslMibObjects 7 }
vdslChanPerfDataEntry OBJECT-TYPE
SYNTAX VdslChanPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslChanPerfDataTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslChanPerfDataTable 1 }
VdslChanPerfDataEntry ::=
SEQUENCE
{
vdslChanValidIntervals HCPerfValidIntervals,
vdslChanInvalidIntervals HCPerfInvalidIntervals,
vdslChanFixedOctets ZeroBasedCounter64,
vdslChanBadBlks ZeroBasedCounter64,
vdslChanCurr15MinTimeElapsed HCPerfTimeElapsed,
vdslChanCurr15MinFixedOctets HCPerfCurrentCount,
vdslChanCurr15MinBadBlks HCPerfCurrentCount,
vdslChan1DayValidIntervals HCPerfValidIntervals,
vdslChan1DayInvalidIntervals HCPerfInvalidIntervals,
vdslChanCurr1DayTimeElapsed HCPerfTimeElapsed,
vdslChanCurr1DayFixedOctets HCPerfCurrentCount,
vdslChanCurr1DayBadBlks HCPerfCurrentCount
}
vdslChanValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 1 }
vdslChanInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 2 }
vdslChanFixedOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets since the unit was last reset."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 3 }
vdslChanBadBlks OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks since the unit was last
reset."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 4 }
vdslChanCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { vdslChanPerfDataEntry 5 }
vdslChanCurr15MinFixedOctets OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 6 }
vdslChanCurr15MinBadBlks OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 7 }
vdslChan1DayValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 8 }
vdslChan1DayInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 9 }
vdslChanCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning
of the current 1-day interval."
::= { vdslChanPerfDataEntry 10 }
vdslChanCurr1DayFixedOctets OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets since the beginning of the
current 1-day interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 11 }
vdslChanCurr1DayBadBlks OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks since the beginning of the
current 1-day interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 12 }
vdslChanIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu channel data
collection interval. VDSL channel interfaces are those
ifEntries where ifType is equal to interleave(124) or
fast(125)."
::= { vdslMibObjects 8 }
vdslChanIntervalEntry OBJECT-TYPE
SYNTAX VdslChanIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslChanIntervalTable."
INDEX { ifIndex,
vdslPhysSide,
vdslChanIntervalNumber }
::= { vdslChanIntervalTable 1 }
VdslChanIntervalEntry ::=
SEQUENCE
{
vdslChanIntervalNumber Unsigned32,
vdslChanIntervalFixedOctets HCPerfIntervalCount,
vdslChanIntervalBadBlks HCPerfIntervalCount
}
vdslChanIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number 1 is the most recent
previous interval; interval 96 is 24 hours ago.
Intervals 2 to 96 are optional."
::= { vdslChanIntervalEntry 1 }
vdslChanIntervalFixedOctets OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanIntervalEntry 2 }
vdslChanIntervalBadBlks OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanIntervalEntry 3 }
vdslChan1DayIntervalTable OB