SNMP MIB Search

An entry in the DSX3 Configuration table.

The number of DSX3 configuration entries (regardless
of their current configuration) in the cwDsx3ConfigTable.

An entry in the DSX3 Alarm Configuration table.
Thresholds may be configured for:
Line Code Violations          (LCV),
LineErrored Seconds           (LES),
Line Severely Errored Seconds (LSES),
P-bit Coding Violations       (PCV),
P-bit Errored Seconds         (PES),
P-bit Severely Errored Seconds(PSES),
Severely Errored Seconds      (SES),
Severely Errored Framing Seconds(SEFS),
Unavailable Seconds            (UAS),
C-bit coding violations        (CCV),
C-bit errored seconds          (CES),
C-bit errored seconds          (CSES).
Once these thresholds are exceeded, minor or major alarms
are raised. Please refer to RFC2496 for descriptions of these
errors.

An entry in the DSX3 Alarm table. The bucket
statistics(15 minute and 24 hour interval statistics)
are gathered for each ds3/e3 interface.
Any entry is created automatically when ds3 interface
is created.

An entry in the table. Statistics are gathered
for each ds3/e3 interface. An entry is created
automatically for each ds3/e3 interface that
is activated.

An entry in the DSX3 PLCP Configuration table.

This variable indicates the maximum number of
entries in cwDsx3ConfigTable.

An entry in the DSX3 PLCP Alarm Configuration table.
Thresholds may be configured for:
Errored Seconds           (ES)
Coding Violations         (CV)
Severely Errored Seconds  (SES)
Unavailable Seconds       (UAS),
Once these thresholds are exceeded, minor or major alarms
are raised. Please refer to RFC2496 for descriptions of these
errors.

An entry in the ATM DS3 PLCP alarm table.
Bucket statistics (15 minute and 24 Hour interval)
are gathered for each ds3/e3 interface automatically.

An entry in the DS3 PLCP counter table.

The maximum number of entries in
the dsx3PlcpCounterTable.

This object is the identifier of a DS3/E3
Interface on a managed device.
The range supported depends upon the type of
the card(controller card, service module).
For 1 port Card :  Range is 1..1
Example : CESM-T3E3
For 2 Port Card :  Range is 1..2
Example : PXM1-2T3E3.
For 3 Port Card : Range is 1..3
Example: SRM-3T3

This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation
of the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 is 34.368 Mbps.
The values, in sequence, describe:
TITLE:                     SPECIFICATION:
dsx3CbitParity            ANSI T1.107a-1990   [9a]
g832-g804                 ITU-T  G.832, G.804
dsx3M23                   ANSI T1.107-1988    [9]
g751                      ITU-T G.751
CESM-T3 supports only ds3Unframed linetype.
CESM-E3 supports only e3Unframed linetype.

This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.
dsx3B3ZS(1) : Bipolar 3-Zero Substitution(B3ZS) suppression.
e3HDB3  (2) : High-Density Bipolar 3(HDB3) suppression.

This object specifies the length of the
DS3 Line. This object provides information
for line build out circuitry if it exists
and can use this object to adjust the
line build out.

This object specifies the out of frame decision
criteria.
OOF is declared when errors are detected in  the
framing octets for four consecuitive frames.
fBits3Of8(1) : an OOF condition is declared if at
least 3 of 8 framing bits are in error.
fBits3Of16(2): an OOF is declared if 3 of 16 framing
bits are found to be in error.
notApplicable(3) : used in case where it is not
applicable. This value can not be set.
This object is not applicable when cwDsx3LineType is
set to g832-g804(2) or g751(4).
This object is not applicable for CESM-T3/E3

If check C-Bits options is chosen then AIS is declared
when 1010 pattern is found and C-Bits are all zero.
In the other case an AIS condition is declared when the
AIS pattern 1010... is detected irrespective of the state
of the C Bits.
This object does not apply to the E3 interface.
The value notApplicable(3) is used in case of interfaces
where this object is not applicable.
This object is not applicable for CESM-T3/E3.

This variable represents the loopback configuration
of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state.  A device that is
not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx3RemoteLineLoop
Near End loops back Remote data
dsx3LocalLineLoop
Near End loops back Local data(outbound).
dsx3InboundLoopback
Near End in bound loopback Local data(inbound).

This entry specifies the FEAC code validation criteria.
fFEACCodes4Of5(1) : a valid FEAC code is declared if
4 of 5 codes match.
fFEACCodes8Of10(2): a valid FEAC code is declared if
8 of 10 codes match.
fFEACCodesDisable(3) : Do not respond to any valid FEAC code.
This object is not applicable to E3 interface.
This object is not supported in CESM-T3/E3.

This variable indicates what bit-oriented code to transmit
over the far-end alarm and control (FEAC) channel.
The values mean:
dsx3SendNoCode
sending looped or normal data
dsx3SendLineCode
sending a request for a line loopback
dsx3SendPayloadCode
sending a request for a payload loopback
(i.e., all DS1/E1s in a DS3/E3 frame)
dsx3SendResetCode
sending a loopback deactivation request.
dsx3SendDS1LoopCode
sending a request to put part of DS1/E1 within
T3/E3 respectively into loopback.
dsx3SendTestPattern
sending a test pattern.
This object is not applicable for CESM-T3/E3

This object enables/disables the BERT function on
an interface.
The possible values are :
disabled(1): disables port BERT functionality
enabled (2): enables port BERT functionality.
value specified in dsx3LineBERTPattern
is transmitted over the interface.
The far end may be looped back and the
test pattern verified.

This object defines the test bit pattern to be
used for BERT.
The possible values are :
Repetitive Patterns
allZero(1): All Zeroes(Continuous spaces).  This is
repeating pattern of zeros(...000...).
The use of this pattern is to test and verify
that the ones density policing mechanism is
functioning properly.  This pattern must be
used in circuits optioned for B8ZS.
allOnes(2): All Ones(Continuous Marks).  This is repeating
pattern of ones(...1111...).  This provides
testing of maximum power level requirements.
The all one pattern test causes the repeater
to consume the maximum amount of power.
If there is insufficient DC span power then the
repeater may begin to fail.
Typically this pattern is used for a simple
continuity check.  It may also be used to detect
the presence of unwanted loop in the network.
alternateOneZero(3): Alternate one/zero pattern(..1010..).  This
pattern produces a 50% ones density.  It is
used to stress the repeater's DC power
consumption.
doubleOneZero(4): Double alternate one/zero(..1100..).
userOneWord(5),
userTwoWords(6),
userThreeWords(7),
userFourWords(8),
pattern2p15minus1(9) :
This is the 2^15-1(32767 bit length)
pattern as specified in ITU O.151.
It has the maximum of 15(inverted) sequential zeros.
This sequence is primarily intended for
error and jitter measurements at bit
rates of 1544, 2048, 6312, 8448,
32064 and 44736 kbit/s.
pattern2p20minus1(10):
This is the 2^20-1(1048575 bits in length)
pattern specified in ITU O.153.It has
the maximum of 19(non-inverted) sequential
zeros.  This pattern is primarily intended
for error measurements at bit rates up to
73kbit/s.  This pattern stresses the
equalization and timing recovery circuitry
of line repeaters.
pattern2p23minus1(11):
This is the 2^23-1(1048575 bits in length) pattern.

Result of BERT Test. The value in this object
is not applicable if dsx3LineBERTEnable is set to
disabled(1).

Setting this object to clear(2) causes the BERT
result field to get cleared.

This object is used for enabling/disabling
G.832 Trail Trace. The trail trace is used to
repetitively transmit a trail access point identifier
so that a trail receiving terminal can verify its
continued connection to the intended transmitter.
It uses a 16-byte numbering format (see Rec E.164).
The first byte of the string is a frame start marker
and includes the result of a CRC-7 calculation over
the previous frame.
The value of this object is set to disable(1) in case
of cards where this feature is not supported.
This object is not applicable for FRSM-VHS and
CESM-T3/E3.

This object is used for specifying the
data to be used for G.832 Trail Trace ID/String.
This object is applicable only for E3 interfaces
with G.832 framing.
The trail trace ID is a 16 octet field that
contains 1 octet of CRC-7(first octet) and 15
octets of data.
The CRC-7 is automatically calculated by the
system(card supporting this feature).
The format of the value is:
Frame Start Marker Error(HEX): CRC-7
Bytes 2-6   (ASCII) [Byte 1-5 of this object]
Bytes 7-11  (ASCII) [Byte 6-10 of this object]
Bytes 12-16 (ASCII) [Byte 11-15 of this object]
This object is not applicable for FRSM-VHS and
CESM-T3/E3.

Received G.832 Trail Trace string.
The format of the value is:
First byte indicates CRC-7(frame start marker).
Bytes 2-6   (ASCII) [Byte 1-5 of this object]
Bytes 7-11  (ASCII) [Byte 6-10 of this object]
Bytes 12-16 (ASCII) [Byte 11-15 of this object]
The value of all zeroes indicates bad CRC-7.
This object is not applicable for FRSM-VHS and
CESM-T3/E3.

Transmitted timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is traceable to a primary
reference clock and is otherwise set to untraceable(2).
This is always set to untraceable(2) in case of
card where this feature is not supported.
This feature is not supported in FRSM-VHS and
CESM-T3/E3.

Received timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is tracable to a primary
reference clock and is otherwise set to untraceable(2).
This is always set to untraceable(2) in case of
card where this feature is not supported.
This feature is not supported in FRSM-VHS and
CESM-T3/E3.

This object specifies the G.832 payload type
for transmit data.
The possible values are :
unequipped (1): not carrying any payload
equipped   (2): Equipped,non-specific
atm        (3): ATM
sdhtu12s   (4): SDH Elements mapping
It is recommended that this object is not instantiated
in case of cards which does not support G.832 functionality.
This is not supported in FRSM-VHS and CESM-T3/E3

Received payload type field in G.832 byte
The possible values are :
unequipped (1): not carrying any payload
equipped   (2): Equipped,non-specific
atm        (3): ATM
sdhtu12s   (4): SDH Elements mapping
It is recommended that this object is not instantiated
in case of cards which does not support G.832 functionality.
This is not supported in FRSM-VHS and CESM-T3/E3

This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.
This is not supported in FRSM-VHS and CESM-T3/E3.

This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.
This object is not supported in FRSM-VHS
and CESM-T3/E3.

This object is used for enabling/disabling an interface
and modifying the interface configuration.
The possible values are:
disable (1): Interface is administratively down
enable  (2): Interface is administratively up.
modify  (3): Used for modifying the parameters
of an interface that has been already
enabled(administratively up).
To modify the parameters of this table, the value
of this object must be set to enable(2) or modify(3).

Specify which DS1 or DS3 line in the far-end for the
loopback testing.
For CESM-T3/E3, only ds3line(30) is valid.

The source of the transmit clock.
backplaneClk(2) : clock source is from the backplane.
recoverClk  (3) : clock source is derived from another
t3 interface.
localClk    (4) : clock source is from a local
oscillator on the card

This is a bitmap of the DSX3 FarEnd line
loopback status bits
Bit Position    Loopback indicator
-----------    -----
1              DS1 Line 1
2              DS1 Line 2
3              DS1 Line 3
4              DS1 Line 4
5              DS1 Line 5
6              DS1 Line 6
7              DS1 Line 7
8              DS1 Line 8
9              DS1 Line 9
10             DS1 Line 10
11             DS1 Line 11
12             DS1 Line 12
...
...
...
28             DS1 Line 28
29             all DS1 Lines
30             DSX3
For CESM-T3/E3, only DSX3 bit (bit 30) is valid.

This object indicates whether the internal equalizer
is being used or bypassed. Set this value depending on
the line equipment to which the receiver is attached.
intrnlequalizer(1): Use internal line equalizer
extequalizer(2)   : Use External equalizer or bypass internal
equalizer.

This is a bitmap of the DSX3 NearEnd line
loopback status bits
BitPosition    Loopback indicator
-----------    -----
1              DS1 Line 1
2              DS1 Line 2
3              DS1 Line 3
4              DS1 Line 4
5              DS1 Line 5
6              DS1 Line 6
7              DS1 Line 7
8              DS1 Line 8
9              DS1 Line 9
10             DS1 Line 10
11             DS1 Line 11
12             DS1 Line 12
...
...
...
28             DS1 Line 28
29             DS1 Line 29
30             DSX3
For CESM-T3/E3, only DSX3 bit (bit 30) is valid.

This variable controls whether the DS3 subrates are
enabled or not. The DS3 subrate is part of
DSU functionality.
This object is currently supported only in FRSM-VHS
cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality.

The dsx3DsuSelect variable controls the type of DSU mode
to be selected. The 'dsx3SubRateEnable' has to be set to
'enable' before selecting the mode in 'dsx3DsuSelect'.
The possible values for this are :
dl3100Mode     - Indicates compatibility with Digital Link Inc's
DL3100 DSU mode of operation. This mode permits
line rates to be in multiples of 300 Kbps.
adcKentroxMode - Indicates compatibility with ADC Kentrox's DSU.
This mode permits line rates to be in multiples
of 500 Kbps.
larsCom        - Indicates compatability with LarsCom DSU.
clearChannel   - Indicates the standard G.751 framing format
(12 overhead bits and 1524 data bits in an E3
frame).This option is supported only in FRSM-2E3.
dsuAlgorithm1  - dsuAlgorith4  - Presently this is not used in any of
the cards.
This object is supported only in FRSM-VHS cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality.

The desired line rate when 'dsx3SubRateEnable' is enabled.
If dsx3DsuSelect is set to 'dl3100Mode', the line rate can
be configured in steps of 300 Kbps.
If dsx3DsuSelect is set to  'adcKentroxMode', the line rate can
be configured in steps of 500 Kbps.
This object is supported only in FRSM-VHS cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality.

This variable turns the scrambling feature ON/OFF
The scrambling is a technique that enables framing
to be maintained on certain medium-speed edge and
trunk interfaces.
This object is ONLY applicable for FRSM-2T3/E3.

This variable is used to setup the severity of RED
alarm. So when LOS/LOF alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
LOF detection is not applicable for CESM-8T3/E3.

This variable is used to setup the severity of RAI
alarm. So when RAI alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
This is not applicable for CESM-T3/E3.

This parameter specifies the increment to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 6
and the integration counter is incremented by
this value every 10 ms while the alarm persists.
The counter is decremented by the value of
dsx3NEAlarmDnCount while there is no alarm
(the counter does not decrement below zero).
When the integration counter exceeds
dsx3NEAlarmThreshold an Alarm of the severity
specified for the particular NE alarm is declared.
LOF detection is not applicable for CESM-T3/E3

This parameter specifies the decrement to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 1 and
the integration counter is decremented by this value
every 10 ms while no alarm persists. The counter is
incremented by the value of dsx3NEAlarmUpCount
while there is no alarm (the counter does not decrement below
zero). When the integration counter reaches zero any Alarm
previously declared is removed.
LOF detection is not applicable for CESM-T3/E3

The value set in this object determines the value that
the alarm integration counter must reach for an near end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integrated in
2.5 sec and removed in 15 seconds.

This parameter specifies the increment to the
Far End alarm integration counters. The local alarms
are RAI and AIS. The Default value is 6 and the
integration counter is incremented by this value every
10 ms while the alarm persists. The counter is decremented
by the value of dsx3FEAlarmDnCount while there is no alarm
(the counter does not decrement below zero).
When the integration counter exceeds dsx3FEAlarmThreshold
an Alarm of the severity specified for the particular far end
alarm is declared.
This object is not applicable for CESM-T3/E3. 

This parameter specifies the decrement to the
Far End alarm integration counters. The local alarms
are AIS and RAI. The Default value is 1. The integration
counter is decremented by this value every 10 ms
(till zero), while no alarm persists. The counter is
incremented by the value of dsx3FEAlarmUpCount
while there is no alarm.  When the integration counter
decrements to zero any previously declared Alarm is removed.
This object is not applicable for CESM-T3/E3. 

The value set in this object determines the value that
the alarm integration counter must reach for an far end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integrated in
2.5 sec and removed in 15 seconds.
This object is not applicable for CESM-T3/E3. 

This variable is used to setup the severity of
any of the Statistical alarms. So when a
Statistical Counter exceeds its specified threshold
the card will send the alarm with appropriate
severity. A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.

The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.

The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.

The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface.

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval.
This object is not supported in CESM-T3/E3
This object is not applicable for E3 interface.

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object does not apply to the E3 interface.
This object is not supported in CESM-T3/E3.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3

The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
This object is not supported in CESM-T3/E3

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3

The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
This object is not supported in CESM-T3/E3

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.

The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval

G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3.

G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.
This object is not supported in CESM-T3/E3.

G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.
This object is not supported in CESM-T3/E3.

G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3

G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3

G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.

The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.

The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.

This variable is a bitmap of the DSX3 Line ALarms
on the card. A value of zero indicates no alarms.
Itemized below are the individual bits:
BitPosition    Alarm
-----------    -----
0              Receiving RAI
1              Transmitting RAI
2              Receiving AIS
3              Transmitting AIS
4              Receiving OOF
5              Receiving LOS
6              Near End Local Loopback in effect
7              Near End Remote Loopback in effect
8              Receiving test pattern
9              Receive LCD
10             Receiving C-bit Parity pattern

This is a bitmap of the DSX3 Line Statistical
Alarms on the card. Zero indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition    Alarm
-----------    -----
0              LCV 15 minute threshold exceeded
1              LCV 24 hour threshold exceeded
2              LES 15 minute threshold exceeded
3              LES 24 hour threshold exceeded
4              LSES 15 minute threshold exceeded
5              LSES 24 hour threshold exceeded
6              PCV 15 minute threshold exceeded
7              PCV 24 hour threshold exceeded
8              PES 15 minute threshold exceeded
9              PES 24 hour threshold exceeded
10             PSES 15 minute threshold exceeded
11             PSES 24 hour threshold exceeded
12             SEFS 15 minute threshold exceeded
13             SEFS 24 hour threshold exceeded
14             AISS 15 minute threshold exceeded
15             AISS 24 hour threshold exceeded
16             UAS 15 minute threshold exceeded
17             UAS 24 hour threshold exceeded
18             BIP8CV/G.832 15 minute threshold exceeded
19             BIP8CV/G.832 24 hour threshold exceeded
20             BIP8ES/G.832 15 minute threshold exceeded
21             BIP8ES/G.832 24 hour threshold exceeded
22             BIP8SES/G.832 15 minute threshold exceeded
23             BIP8SES/G.832 24 hour threshold exceeded
24             CCV 15 minute threshold exceeded
25             CCV 24 hour threshold exceeded
26             CES 15 minute threshold exceeded
27             CES 24 hour threshold exceeded
28             CSES 15 minute threshold exceeded
29             CSES 24 hour threshold exceeded
Bits 18 to 23 do not have any significance if the framing is
G.751(which is used in FRSM_VHS)
only bits 0,1,2,3,4,5,16 and 17 are applicable to CESM-T3/E3.

The number of Line Code Violations(LCV)
encountered by the interface in current
15 minute period.

The number of Line Code Violations(LCV)
encountered by the interface in current
last 15 minute period.

The number of Line Code Violations(LCV)
encountered by the interface in current
last 24 hour period.

The number of Line Errored Seconds(LES)
encountered by the interface in current
15 minute period.

The number of Line Errored Seconds(LES)
encountered by the interface in last
15 minute period.

The number of Line Errored Seconds(LES)
encountered by the interface in last
24 hour period.

The number of Line Severely Errored Seconds(LSES)
encountered by the interface in current
15 minute period.

The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
15 minute period.

The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
24 hour period.

The number of P-bit Coding Violations(PCV)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3

The number of P-bit Coding Violations(PCV)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3

The number of P-bit Coding Violations(PCV)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3

The number of P-bit Errored Seconds(PES)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3

The number of P-bit Errored Seconds(PES)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3

The number of P-bit Errored Seconds(PES)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3

The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in current 15 minute period.
This object is not supported in CESM-T3/E3

The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 15 minute period.
This object is not supported in CESM-T3/E3

The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 24 Hour period.
This object is not supported in CESM-T3/E3

The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in current 15 minute period.
This object is not supported in CESM-T3/E3

The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 15 minute period.
This object is not supported in CESM-T3/E3

The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 24 Hour period.
This object is not supported in CESM-T3/E3

The number of AIS Severely Errored Seconds
encountered by the interface in current 15 minute
period.
This object is not supported in CESM-T3/E3

The number of AIS Severely Errored Seconds
encountered by the interface in last 15 minute
period.
This object is not supported in CESM-T3/E3

The number of AIS Severely Errored Seconds
encountered by the interface in last 24 Hour
period.
This object is not supported in CESM-T3/E3

The number of Unavailable Seconds(UAS)
encountered by the interface in current
15 minute period.

The number of Unavailable Seconds(UAS)
encountered by the interface in last
15 minute period.

The number of Unavailable Seconds(UAS)
encountered by the interface in last
24 Hour period.

This object gives the percentage of
seconds without any LCV Errors in the
total elapsed seconds.

The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in current
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in current
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in current 15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3

Setting this object to dsx3LineAlarmClear will
cause all the alarms statuses and counters to reset.

The number of C-bit Coding Violations(CCV)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3

The number of C-bit Coding Violations(CCV)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3

The number of C-bit Coding Violations(CCV)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3

The number of C-bit Errored Seconds(CES)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3

The number of C-bit Errored Seconds(CES)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3

The number of C-bit Errored Seconds(CES)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3

The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in current 15 minute period.
This object is not supported in CESM-T3/E3

The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 15 minute period.
This object is not supported in CESM-T3/E3

The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 24 Hour period.
This object is not supported in CESM-T3/E3

The number of times the Loss of Signal was detected
with or without integrating to LOS alarm.

The number of times the Out of Frame was detected
with or without integrating to OOF alarm.
This object is not supported in CESM-T3/E3

The number of times Yellow Alarms was detected with
or without integrating to RAI alarm.
This object is not supported in CESM-T3/E3

The counter associated with the number of C Bit
Coding Violations encountered by a DS3/E3 interface.
This object is not supported in CESM-T3/E3

The number of Framing Pattern Errors encountered by
a DS3/E3 interface.
This object is not supported in CESM-T3/E3

The number of Header Check Sequence(HCS) Errors.
This object is not supported in CESM-T3/E3

The number of HEC errored seconds.
This object is not supported in CESM-T3/E3

The number of Severely HEC error seconds.
This object is not supported in CESM-T3/E3

This variable is used to clear all the counters.

The number of P-bit parity error.
This object is not supported in CESM-T3/E3

The number of Far-end block error.
This object is not supported in CESM-T3/E3

The number of excessive zeros
This object is not supported in CESM-T3/E3

The counter associated with the number of Line
Coding Violations encountered by a DS3/E3 interface.

This object identifies the dsx3 PLCP interface.
The value of this object must be same as the value
specified in 'dsx3LineNum' object from cwDsx3ConfigTable.

The value for this object sets the cell delineation
method used by the interface. The cell delineation
defines how a receiving device recognizes the start
and end of an ATM cell.
framingByPlcp   (1): The ATM Cells are in predetermined
location within each PLCP row, so
no additional method is needed to
delineate ATM cells.
framingByAtmHec (2): The Header Error Control field of the
ATM cell header is used to delineate
ATM cells.

The value for this object is used for enabling/disabling
PLCP cell scrambling.

specifies the type of loopback on the line.
The possible value(s) are :
noLoop         (1): Not in loopback.
remoteLineLoop (2): Remote Line Loopback.
localLineLoop  (3): Local Line Loopback.

This variable is used to setup the severity of PLCP RED
alarm. So when PLCP_OOF alarm is detected the card will
declare the alarm with appropriate severity status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.

This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP RAI alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.

This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP LSS alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.

This objects specifies whether the LSS feature is
enabled/disabled.

This object derfines the value of the LSS code
that is to be interpreted as Link Connected.

This object defines the value of the LSS code
that is to be identified as Receive Link Down.

This object defines the value of the LSS code that
is to be interpreted as Receive Link Up.

This variable sets up the severity of PLCP Statistical
alarm. So when PLCP Statistical alarm is detected, the
card will send the alarm with appropriate severity.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval

The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.

The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval

This variable is a bitmap of the DSX3 Line alarms.
A value of zero indicates no alarms.
Itemized below are the individual bits:
BitPosition    Alarm
-----------    -----
0              Receiving RAI
1              Transmitting RAI
2              Receiving OOF
3              Receiving LSS Link Up
4              Transmitting LSS Link Up
5              Receiving LSS Link Down
6              Transmitting LSS Link Down
7              Near End Local Loopback in effect
8              Near End Remote Loopback in effect

This variable is a bitmap of the DSX3 Line Statictical
Alarms on the card. A value of zero indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition    Alarm
-----------    -----
0              Bip8CV 15 minute threshold exceeded
1              Bip8CV 24 hour threshold exceeded
2              Bip8ES 15 minute threshold exceeded
3              Bip8ES 24 hour threshold exceeded
4              Bip8SES 15 minute threshold exceeded
5              Bip8SES 24 hour threshold exceeded
6              Plcp SEFS 15 minute threshold exceeded
7              Plcp SEFS 24 hour threshold exceeded
8              Plcp UAS 15 minute threshold exceeded
9              Plcp UAS 24 hour threshold exceeded

This counter counts the number of
BIP-8 code violations encountered by the interface.

The counter associated with the number of
BIP-8 code violations in the last 15 minute period
encountered by the interface.

The counter associated with the number of
BIP-8 code violations in the last 24 hour period
encountered by the interface.

This counter counts the number of
BIP-8 code violations Errored Seconds
encountered by the interface.

This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 15 minutes encountered by the interface.

This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 24 hours encountered by the interface.

This counter counts the number of
Bip8 code violations Severely Errored Seconds
encountered by the interface.

This counter counts the number of
BIP-8 Severely Errored Seconds in the last
15 minutes encountered by the interface.

This counter counts the number of
BIP-8 Severely Errored Seconds in the last
24 hours encountered by the interface.

This counter counts the number of
Severely Errored Framing Seconds
encountered by the interface.

This counter counts the number of
Severely Errored Framing Seconds in the last
15 minutes encountered by the interface.

This counter counts the number of
Severely Errored Framing Seconds in the last
24 hours encountered by the interface.

This counter counts the number of
Unavailable Seconds encountered by the interface.

This counter counts the number of
Unavailable Seconds in the last 15 minutes
encountered by the interface.

This counter counts the number of
Unavailable Seconds in the last 24 hours
encountered by the interface.

This variable is used to clear all the alarms.

The number of BIP-8 errors encountered by
the interface.

The number of times the Out of Frame(OOF) was detected
with or without integrating to OOF alarm.

The number of times Remote Alarm Indication(RAI)
was detected with or without integrating to RAI alarm.

The number of Framing Errors detected.

The number of Framing Error errored seconds.

The number of Severely errored Framing error seconds.

The number of Far End Block Errors(FEBE) detected.

The number of FEBE errored seconds.

The number of Severely errored FEBE seconds.

The number of HCS Errors.

The number of HEC errored seconds.

The number of Severely HEC error seconds.

This variable is used to clear all the counters.

The DS3/E3 Configuration table. There is one row for each
DSX3 port in the system. The table size (number of
rows) is given by the value of dsx3LineNumOfValidEntries.

The DSX3 interface alarm configuration table. This table contains
the parameters associated with detecting and declaring alarms for
the interface. The parameters include severity of alarm, alarm
integration parameters and 15 minute and 24 hour thresholds.
The number of rows is given by dsx3LineNumOfValidEntries.

The DSX3 interface alarm table. This table
contains the performance statistics and Error Events
based on 15 minute and/or 24 hour interval.
Performance Parameters:
LES  : Line Errored Seconds
PES  : P-bit Errored Seconds
PSES : P-bit Severely Errored Seconds
CES  : C-bit Errored Seconds
CSES : C-bit Severely Errored Seconds
SEFS : Severely Errored Framing Seconds
UAS  : Unavailable Seconds
Error Events:
BPV : Bipolar Violation
EXZ : Excessive Zeros
LCV : Line Coding Violation
PCV : P-bit Coding Violation
CCV : C-bit Coding Violation.

This table is for ds3/e3 statistics. This table
maintains the number of times the line encountered
LOS, LOF, AIS, RAI, CCV and Framing Errors(FE)
from the time it is up. Error statistics are
cleared when the line is brought up from the failure
state.

This table contains ATM interface DS3 PLCP
configuration parameters.

This table contains the ATM interface PLCP alarm
parameters.

This table contains ATM interface DS3 PLCP
alarm configuration.

The table for DS3 PLCP counter table.

The MIB Module for DS3/E3 interface
configuration , statistics and Alarm
configuration.
This MIB is supported in T3/E3 service modules
in MGX products.
Some of the T3/E3 service modules(Cards) are:
PXM1     : Processor Switch Module.
CESM-T3E3: Circuit Emulation Service Module
FRSM-VHS : Frame Relay Service Module. Includes
T3 and Channelized T3 categories.
FRSM-2CT3: Channelized FRSM Module
SRM-3T3  : Service Resource Module
Terminologies Used :
SDH     : SONET Digital Hierarchy
PLCP    : Physical Layer Convergence Procedure.
BERT    : Bit Error Rate Testing.
FEAC    : Far End Alarm Code.
OOF     : Out Of Frame.
AIS     : Alarm Indication Signal.
LOF     : Loss Of Frame.
RAI     : Remote Alarm Indication.
HCS     : Header Check Sequence
HEC     : Header Error Control
MA byte : Maintenance and Adaptation byte
Tx MA Byte: This is explained in ITU-T G.832
This Byte contains following fields:
Payload type
Payload dependent bits
Timing maker bit
Rx MA Byte: This is explained in ITU-T G.832
This Byte contains following fields:
Payload type
Timing maker bit

The collection of objects which are used for
providing number of entries in dsx3 and PLCP
tables.

The collection of objects which are used for
configuring DS3/E3 interfaces.

The collection of objects which are used for
BERT on DS3/E3 interfaces.

The collection of objects related to
DS3/E3 statistics.

The collection of objects used for
alarm configuration of DS3 and E3 interfaces.

The collection of objects related to
performance statistics and error events
for ds3 end e3 interfaces.

The collection of objects related to
PLCP Configuration on DS3 interfaces.

The collection of objects related to
PLCP statistics on DS3 interfaces.

The collection of objects used for
PLCP Alarm configuration on DS3 interfaces.

The collection of objects used for
PLCP Alarm configuration on DS3 interfaces.

The collection of objects which are applicable
for E3 interfaces only.

The collection of objects used for
alarm configuration of DS3 interfaces.

The collection of objects used for
alarm configuration of E3 interfaces.

The collection of objects related to
performance statistics and error events
for ds3 interfaces.

The collection of objects related to
performance statistics and error events
for e3 interfaces.