| Scalar Object |
| bbIfCnfPortGrpEntry | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1 |
An entry for the logical interface. The interface may be further
be configured to be used as a virtual trunk OR as a UNI Port.
|
| nextBbIfNumAvailable | .1.3.6.1.4.1.351.110.5.2.6.1.1.2 |
Indicates the next logical broadband interface
number that is available. |
| bbIfStateGrpEntry | .1.3.6.1.4.1.351.110.5.2.6.3.1.1 |
An entry for each logical interface representing
the state. |
| bbIfCntGrpEntry | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1 |
An entry for logical interface. |
| Tabular Object |
| bbIfNum | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.1 |
This is logical interface number within a physical line num.
In MGX PXM1 card, a physical port can have a maximum of 32 logical
interfaces. |
| bbIfRowStatus | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.2 |
This variable enables or disables the logical interface.
1 - enable
2 - disable
3 - modify |
| bbIfAdmin | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.3 |
This variable enables or disables the logical interface.
1 - up
2 - down
3 - writeOnly |
| bbIfLineNum | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.4 |
The line number associated with the logical interface.
For PXM1, there is currently 4 physical lines. |
| bbIfIngrPctBandwidth | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.5 |
The percentage of aggregate physical line bandwidth, available for
this broadband interface - Ingress. Default is 0 %. |
| bbIfEgrPctBandwidth | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.6 |
The percentage of aggregate physical line bandwidth, available for
this broadband interface - Egress . Default is 0 %. |
| bbIfMinVpi | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.7 |
The lower limit of VPI range to be reserved for
this logical interface. |
| bbIfMaxVpi | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.8 |
The upper limit of VPI range to be reserved
for this logical interface.
For virtual trunks, bbIfMinVpi and bbIfMaxVpi should
be the same. |
| bbIfSpeed | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.9 |
The speed of the port in cells per second. |
| bbIfMaxCellRatePct | .1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.10 |
The maximum cell rate allowed for the port in terms of
percentage. Must be greater than or equal to
bbIfIngrPctBandwidth.
The default is 100 percent. |
| bbStateIfNum | .1.3.6.1.4.1.351.110.5.2.6.3.1.1.1 |
This is logical interface number within a physical line num.
In MGX PXM1 card, a physical port can have a maximum of
32 logical interfaces. |
| bbIfState | .1.3.6.1.4.1.351.110.5.2.6.3.1.1.2 |
This variable indicates the status of the logical interface.
The following values are not supported for the logical interface.
remoteloopback (3),
outofcelldelineation (6),
localloopback (7). |
| bbIfOversubscribed | .1.3.6.1.4.1.351.110.5.2.6.3.1.1.3 |
This variable indicates the whether the logical interface is
over subscribed or not. |
| bbIfIngrPercentUtil | .1.3.6.1.4.1.351.110.5.2.6.3.1.1.4 |
Percentage Utilization of the interface in the
Ingress direction. |
| bbIfEgrPercentUtil | .1.3.6.1.4.1.351.110.5.2.6.3.1.1.5 |
Percentage Utilization of the interface in
the Egress direction. |
| bbCntIfNum | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.1 |
Refers to the logical interface index. |
| bbIfTotalCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.2 |
Total number of cells (VC plus Qbin) that belong
to this Interface. This maps on to the virtual interface of QE. |
| bbIfRcvValidOAMCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.3 |
Total number of OAM cell received. |
| bbIfRcvRmCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.4 |
Total number of RM cells Received. |
| bbIfRcvClp0Cells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.5 |
Total number of CLP-0 cells Received. |
| bbIfRcvClp1Cells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.6 |
Total number of CLP-1 cells Received. |
| bbIfRcvClp0DiscCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.7 |
Total number of CLP-0 cells discarded at Ingress. |
| bbIfRcvClp1DiscCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.8 |
Total number of CLP-1 cells discarded at Ingress. |
| bbIfXmtOAMCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.9 |
Total number of OAM cells transmitted. |
| bbIfXmtRmCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.10 |
Total number of RM cells transmitted. |
| bbIfXmtClp0Cells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.11 |
Total number of CLP-0 cells transmitted. |
| bbIfXmtClp1Cells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.12 |
Total number of CLP-1 cells transmitted. |
| bbIfCntClrButton | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.13 |
Writing a value of 2 resets all the counters. |
| bbIfRcvErroredCells | .1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.14 |
Total number of cells with Invalid VPI VCI or
Invalid PTI fields This is a card level counter and
hence will be the same for all instances of the ports. |
| Table |
| bbIfCnfPortGrpTable | .1.3.6.1.4.1.351.110.5.2.6.1.1.1 |
The Broadband Interface config table is for logical interface.
There will an entry for each of the logical partition of the
physical line.
|
| bbIfStateGrpTable | .1.3.6.1.4.1.351.110.5.2.6.3.1 |
The state table for the logical interface. |
| bbIfCntGrpTable | .1.3.6.1.4.1.351.110.5.2.6.4.1.1 |
The Broadband Interface Count table is for logical interface.
There will an entry for each of the logical partition of the
physical line. |
| Object Identifier |
| ciscoWanBbifPortMIB | .1.3.6.1.4.1.351.150.32 |
The MIB module for configuration of ATM logical
ports in PXM1 Service module in MGX82xx series.
This MIB contains information on ATM Logical
port statistics. |
| bbIfCnfPortGrp | .1.3.6.1.4.1.351.110.5.2.6.1.1 |
| bbIfCntGrp | .1.3.6.1.4.1.351.110.5.2.6.4.1 |
| cwbPortMIBConformance | .1.3.6.1.4.1.351.150.32.2 |
| cwbPortMIBGroups | .1.3.6.1.4.1.351.150.32.2.1 |
| cwbPortMIBCompliances | .1.3.6.1.4.1.351.150.32.2.2 |
| Group |
| cwbPortConfGroup | .1.3.6.1.4.1.351.150.32.2.1.2 |
The collection of objects which are used for
configuring ATM logical ports(known as
broad band interface ports). |
| cwbPortStatsGroup | .1.3.6.1.4.1.351.150.32.2.1.4 |
The collection of objects containing
the statistics information for
ATM Logical ports. |
| cwbPortGenearlGroup | .1.3.6.1.4.1.351.150.32.2.1.1 |
The collection of objects which are applicable
for general information about logical ports. |
| cwbPortStateGroup | .1.3.6.1.4.1.351.150.32.2.1.3 |
The collection of objects which are used for
finding the state of ATM logical ports(known as
broad band interface ports). |