SNMP MIB Search

An entry for each logical port. Each entry
contains information on the port type, DS0s
configured and number of DS0 subcircuits.

This variable contains the next UNUSED logical port number
of the possible 32 DS0s * n ports.
This number can be used in channel config table, the
cesportNextAvailable gets updated if the number gets
used to create a logical port.
A '0' indicates that no more ports are available.

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 1

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 2.

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 3

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1.
This is for line 4

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 5

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 6

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 7

Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 8

This object identifies the logical port number.
The range support depends upon the type of the
service module(Card).
- 8 port T1 Card, range is 1..192.
- 8 port E1 Card, range is 1..248.
- 1 port T3 Card, range is 1..1.
Range is caclulated as follows. This can be
used for calculating the range for other type
of cards.
For T1 Card: (24 * Number of T1 Ports)
For E1 Card: (31 * Number of E1 Ports).

This variable enables or modifies the port
1 - add : Add a logical port
2 - del : Delete a logical port
3 - mod : Modify a logical port.

This object represents the line number to
which this port is associated.
The supported range depends upon the type of
service module(card).

This object represents port type whether it is
carrying  subrate circuits.
structured    : This is  for SDT(Structured Data Transfer).
This type of port supports following
features:
* intended to emulate point-to-point
fractional DS1 or E1 circuit.
* Synchronous timing
* Fractional(Nx64 Kbps)DS1/E1 service
(Contiguous timeslots only).You can
map an Nx64 Kbps channel to any Virtual
Channel(VC).
unstructured  : This is for unstructured data transfer(UDT)
All the DS0 time slots are allocated.
This type of port supports following
features:
* intended to emulate point-to-point
DS1 or E1 circuit.
* Synchronous and Asynchronous timing
framingOnVcDisconnect : similar to unstructured during normal
operation. In case of channel failure
line data will be looped back towards
line.
strau          : only one DS0 time slot is allocated.
The value strau(4) value is not supported in
CESM-8T1/E1 or CESM-T3E3.
CESM-T3E3 card supports value unstructured(2) only.

This represents bit map of DS0s for a line which
are used to form this logical port. Bit 0 represents
DS0-1.

This represents  number of DS0 time slots
configured to this Port. If the cesPortType is
strau(4), then this can not have more than 1 DS0 time slot.

This object represents  number of subcircuit in
the DS0 time slot.
This is applicable only when cesPortType is
strau(4).
8 = there are 8 no .of 8kbps links  (1 bit)
4 = there are 4 no .of 16kbps links (2 bit)
2 = there are 2 no .of 32kbps links (4 bit)
Currently not supported in CESM-8.

This object identifies the configured speed
of port.
Max speed for T1 = 1544
Max speed for E1 = 2038
Max speed for T3 = 44736
Max speed for E3 = 34368.

This variable indicates the state of the
logical port.
The possible values are :
notConfigured  (1) : Port is not configured
active         (2) : Port is in active state
remoteLoopback (3) : Remote Loopback is set
failedDueToLine(4) : Port failed due to some failure in
physical line
failedDueToSignalling(5) : Port failed due to some Signalling
issues.
inactive       (6) : Port is not active
inBert         (7) : Bit Error Rate Test(BERT) in progress.
farEndRemoteLoopback(8): Far End is in loopback.

This variable enables/disables BERT.
This object is not supported in CESM-T3E3.

The config table is for CES logical port.
This is used for configuring the port type
and number of DS0s and number of Subcircuits
in DS0 on the CES port.

The MIB module to configure the Circuit Emulation
Service(CES) ports.

The collection of objects which are used to represent
Circuit Emulation Service Port information.

The collection of objects related to information
on DS0 time slots used in each DS1 line.

The collection of objects which are
applicable for general information about
logical ports.