Wellfleet-CONSOLE-MIB DEFINITIONS ::= BEGIN
IMPORTS
Counter
FROM RFC1155-SMI
OBJECT-TYPE
FROM RFC-1212
DisplayString
FROM RFC1213-MIB
wfSerialPortGroup, wfServices
FROM Wellfleet-COMMON-MIB;
wfConsole OBJECT IDENTIFIER ::= { wfServices 1 }
wfBaudRate OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Baud rate configured on the Technician Interface console"
DEFVAL { 9600 }
::= { wfConsole 1 }
wfDataBits OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Number of data bits configured on the Technician Interface console"
DEFVAL { 8 }
::= { wfConsole 2 }
wfParity OBJECT-TYPE
SYNTAX INTEGER {
none(1),
odd(2),
even(3)
}
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Type of parity configured on the Technician Interface console"
DEFVAL { none }
::= { wfConsole 3 }
wfStopBits OBJECT-TYPE
SYNTAX INTEGER {
s1bit(1),
s15bit(2),
s2bit(3)
}
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Number of stop bits configured on the Technician Interface console"
DEFVAL { s1bit }
::= { wfConsole 4 }
wfModemEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Enable the Technician Interface console to run over a modem"
DEFVAL { disabled }
::= { wfConsole 5 }
wfLinesPerScreen OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Number of lines which can be displayed in one screen on the Technician
Interface console"
DEFVAL { 24 }
::= { wfConsole 6 }
wfMoreEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Enable the 'more' feature on the Technician Interface console"
DEFVAL { enabled }
::= { wfConsole 7 }
wfPrompt OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Character string which will be used as the system prompt on
the Technician Interface console"
::= { wfConsole 8 }
wfLoginTimeOut OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS obsolete
DESCRIPTION
"IF MODEM_ENABLED then time out in minutes to HUP when at the login prompt"
DEFVAL { 1 }
::= { wfConsole 9 }
wfPasswordTimeOut OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Timout on Password entry"
DEFVAL { 1 }
::= { wfConsole 10 }
wfCommandTimeOut OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS obsolete
DESCRIPTION
"IF MODEM_ENABLED then time out in minutes to HUP when at the command prompt"
DEFVAL { 15 }
::= { wfConsole 11 }
wfLoginRetries OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS obsolete
DESCRIPTION
"IF MODEM_ENABLED then limit # of login attempts then HUP"
DEFVAL { 3 }
::= { wfConsole 12 }
wfTotalLogins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Total number of TI login attempts"
::= { wfConsole 13 }
wfUserLoginErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Total number of FAILED User login attempts"
::= { wfConsole 14 }
wfManagerLoginErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Total number of FAILED Manager login attempts"
::= { wfConsole 15 }
wfOtherLoginErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Total number of FAILED Other login attempts"
::= { wfConsole 16 }
wfTtyFrameErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Count of TTY Frame errors"
::= { wfConsole 17 }
wfTtyOverrunErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Count of TTY Overrun errors"
::= { wfConsole 18 }
wfTtyParityErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Count of TTY Parity errors"
::= { wfConsole 19 }
wfTtyInfifoErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS obsolete
DESCRIPTION
"Count of TTY Input Fifo errors"
::= { wfConsole 20 }
wfSerialPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfSerialPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Configuration of system serial port(s)"
::= { wfSerialPortGroup 1 }
wfSerialPortEntry OBJECT-TYPE
SYNTAX WfSerialPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information for each serial port."
INDEX { wfSerialPortNumber }
::= { wfSerialPortTable 1 }
WfSerialPortEntry ::= SEQUENCE {
wfSerialPortDelete
INTEGER,
wfSerialPortDisable
INTEGER,
wfSerialPortState
INTEGER,
wfSerialPortNumber
INTEGER,
wfSerialPortName
DisplayString,
wfSerialPortSlot
INTEGER,
wfSerialPortType
INTEGER,
wfSerialPortBaudRate
INTEGER,
wfSerialPortDataBits
INTEGER,
wfSerialPortParity
INTEGER,
wfSerialPortStopBits
INTEGER,
wfSerialPortModemEnable
INTEGER,
wfSerialPortLinesPerScreen
INTEGER,
wfSerialPortMoreEnable
INTEGER,
wfSerialPortPrompt
DisplayString,
wfSerialPortLoginTimeOut
INTEGER,
wfSerialPortPasswordTimeOut
INTEGER,
wfSerialPortCommandTimeOut
INTEGER,
wfSerialPortLoginRetries
INTEGER,
wfSerialPortTotalLogins
Counter,
wfSerialPortUserLoginErrors
Counter,
wfSerialPortManagerLoginErrors
Counter,
wfSerialPortOtherLoginErrors
Counter,
wfSerialPortTtyFrameErrors
Counter,
wfSerialPortTtyOverrunErrors
Counter,
wfSerialPortTtyParityErrors
Counter,
wfSerialPortTtyInfifoErrors
Counter,
wfSerialPortInitialSearchPath
DisplayString,
wfSerialPortManagerAutoScript
DisplayString,
wfSerialPortUserAutoScript
DisplayString,
wfSerialPortUserAbortLogoutDisable
INTEGER,
wfSerialPortHistoryDepth
INTEGER,
wfSerialPortAutoSaveNumFiles
INTEGER,
wfSerialPortAutoSaveVolume
DisplayString,
wfSerialPortModemIdSwRev
DisplayString,
wfSerialPortModemIdHwRev
DisplayString,
wfSerialPortModemLineState
INTEGER,
wfSerialPortModemCfgFactoryDefaults
INTEGER,
wfSerialPortModemCfgInitString
DisplayString,
wfSerialPortModemCfgDefaultString
DisplayString,
wfSerialPortModemCfgResultCodeString
DisplayString,
wfSerialPortModemCfgState
INTEGER,
wfSerialPortModemCfgCountry
INTEGER,
wfSerialPortModemInitState
INTEGER
}
wfSerialPortDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Flag to indicate Serial Port instance deletion"
DEFVAL { created }
::= { wfSerialPortEntry 1 }
wfSerialPortDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable or disable this Serial Port"
DEFVAL { enabled }
::= { wfSerialPortEntry 2 }
wfSerialPortState OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
init(3),
notpresent(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The state of this Serial Port"
DEFVAL { notpresent }
::= { wfSerialPortEntry 3 }
wfSerialPortNumber OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Serial Port number"
::= { wfSerialPortEntry 4 }
wfSerialPortName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Serial Port name"
::= { wfSerialPortEntry 5 }
wfSerialPortSlot OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Slot number of Serial Port session"
DEFVAL { 0 }
::= { wfSerialPortEntry 6 }
wfSerialPortType OBJECT-TYPE
SYNTAX INTEGER {
ti(1),
printer(2),
rtelnet(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Type of Serial Port"
DEFVAL { ti }
::= { wfSerialPortEntry 7 }
wfSerialPortBaudRate OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Baud rate configured on this Serial Port"
DEFVAL { 9600 }
::= { wfSerialPortEntry 8 }
wfSerialPortDataBits OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of data bits configured on this Serial Port"
DEFVAL { 8 }
::= { wfSerialPortEntry 9 }
wfSerialPortParity OBJECT-TYPE
SYNTAX INTEGER {
none(1),
odd(2),
even(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Type of parity configured on this Serial Port"
DEFVAL { none }
::= { wfSerialPortEntry 10 }
wfSerialPortStopBits OBJECT-TYPE
SYNTAX INTEGER {
s1bit(1),
s15bit(2),
s2bit(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of stop bits configured on this Serial Port"
DEFVAL { s1bit }
::= { wfSerialPortEntry 11 }
wfSerialPortModemEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable the Serial Port to run with modem leads enabled"
DEFVAL { disabled }
::= { wfSerialPortEntry 12 }
wfSerialPortLinesPerScreen OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of lines which can be displayed in one screen on the
Serial Port"
DEFVAL { 24 }
::= { wfSerialPortEntry 13 }
wfSerialPortMoreEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable the 'more' feature on the Serial Port"
DEFVAL { enabled }
::= { wfSerialPortEntry 14 }
wfSerialPortPrompt OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character string which will be used as the system prompt on
the Serial Port"
::= { wfSerialPortEntry 15 }
wfSerialPortLoginTimeOut OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IF MODEM_ENABLED then time out in minutes to HUP when at the
login prompt"
DEFVAL { 1 }
::= { wfSerialPortEntry 16 }
wfSerialPortPasswordTimeOut OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Timout on Password entry"
DEFVAL { 1 }
::= { wfSerialPortEntry 17 }
wfSerialPortCommandTimeOut OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IF MODEM_ENABLED then time out in minutes to HUP when at the
command prompt"
DEFVAL { 15 }
::= { wfSerialPortEntry 18 }
wfSerialPortLoginRetries OBJECT-TYPE
SYNTAX INTEGER(1..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IF MODEM_ENABLED then limit # of login attempts then HUP"
DEFVAL { 3 }
::= { wfSerialPortEntry 19 }
wfSerialPortTotalLogins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total number of TI login attempts on Serial Port"
::= { wfSerialPortEntry 20 }
wfSerialPortUserLoginErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total number of FAILED User login attempts on Serial Port"
::= { wfSerialPortEntry 21 }
wfSerialPortManagerLoginErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total number of FAILED Manager login attempts on Serial Port"
::= { wfSerialPortEntry 22 }
wfSerialPortOtherLoginErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total number of FAILED Other login attempts on Serial Port"
::= { wfSerialPortEntry 23 }
wfSerialPortTtyFrameErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of TTY Frame errors on Serial Port"
::= { wfSerialPortEntry 24 }
wfSerialPortTtyOverrunErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of TTY Overrun errors on Serial Port"
::= { wfSerialPortEntry 25 }
wfSerialPortTtyParityErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of TTY Parity errors on Serial Port"
::= { wfSerialPortEntry 26 }
wfSerialPortTtyInfifoErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of TTY Input Fifo errors on Serial Port"
::= { wfSerialPortEntry 27 }
wfSerialPortInitialSearchPath OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS obsolete
DESCRIPTION
"Example: 'A:;1:;2:' or '2:;4:6:;9:"
::= { wfSerialPortEntry 28 }
wfSerialPortManagerAutoScript OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"for each login."
::= { wfSerialPortEntry 29 }
wfSerialPortUserAutoScript OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"for each login."
::= { wfSerialPortEntry 30 }
wfSerialPortUserAbortLogoutDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"a USER from escaping out of the User Autoscript"
DEFVAL { disabled }
::= { wfSerialPortEntry 31 }
wfSerialPortHistoryDepth OBJECT-TYPE
SYNTAX INTEGER(1..40)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TI command history table size"
DEFVAL { 20 }
::= { wfSerialPortEntry 32 }
wfSerialPortAutoSaveNumFiles OBJECT-TYPE
SYNTAX INTEGER(0..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of times AutoSave will save the log
0 - disable the AutoSave log"
DEFVAL { 0 }
::= { wfSerialPortEntry 33 }
wfSerialPortAutoSaveVolume OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Volume, to which AutoSave will save logs
Example: 'A:' or '2:'"
::= { wfSerialPortEntry 34 }
wfSerialPortModemIdSwRev OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..79))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual description of the modem's
firmware version number."
::= { wfSerialPortEntry 35 }
wfSerialPortModemIdHwRev OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..79))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual description of the revision
number of the modem daughter card."
::= { wfSerialPortEntry 36 }
wfSerialPortModemLineState OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
onHook(2),
offHook(3),
connected(4),
busiedOut(5),
reset(6)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indicates the state of the modem."
DEFVAL { unknown }
::= { wfSerialPortEntry 37 }
wfSerialPortModemCfgFactoryDefaults OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object indicates if factory defaults are to be loaded.
If set to enabled(1), factory defaults are loaded. If set
to disabled(2), the initialization string in
wfModemCfgInitString is not sent to the modem."
DEFVAL { enabled }
::= { wfSerialPortEntry 38 }
wfSerialPortModemCfgInitString OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An initialization string that will be sent to the modem
each time the modem is rebooted."
::= { wfSerialPortEntry 39 }
wfSerialPortModemCfgDefaultString OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The string contains AT comands for initializing the
modem every time the modem comes up, regardless of
configuration."
::= { wfSerialPortEntry 40 }
wfSerialPortModemCfgResultCodeString OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ASCII response string returned by the modem.
Response strings will be returned in response to
last command to the modem and in response to activity
on the line."
::= { wfSerialPortEntry 41 }
wfSerialPortModemCfgState OBJECT-TYPE
SYNTAX INTEGER {
cfgIdle(1),
cfgInProgress(2),
cfgResponseReturned(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Indicates the state of AT command processing. When a
new initialization string is to be sent to the modem,
the sender sets the state to cfgInProgress(2). After the
command has been sent to the modem, and a result code
has been returned, the state is set to
cfgResponseReturned(3). Once the sender
has received the return code, the sender sets the state
to cfgIdle(1)."
DEFVAL { cfgIdle }
::= { wfSerialPortEntry 42 }
wfSerialPortModemCfgCountry OBJECT-TYPE
SYNTAX INTEGER {
northAmerica(1),
japan(2),
uk(3),
germany(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Identifies the country the modem is designed to operate
in. This object is not read from the modem directly.
It must be entered manually when configuring the modem."
DEFVAL { northAmerica }
::= { wfSerialPortEntry 43 }
wfSerialPortModemInitState OBJECT-TYPE
SYNTAX INTEGER {
startup(1),
getInfo(3),
setDefaults(4),
initialization(5),
initComplete(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indictes the state of the modem initialization sequence. The state will
freeze in the state that fails when a failure is detected. Otherwise,
the state will be set to initComplete when initialization completes
successfully. The state number correspond to those for the COM port
modems. Some of the states are not valid for the console modem."
::= { wfSerialPortEntry 44 }
END