Wellfleet-NAT-MIB DEFINITIONS ::= BEGIN
IMPORTS
IpAddress, Counter, Gauge
FROM RFC1155-SMI
OBJECT-TYPE
FROM RFC-1212
wfNatGroup
FROM Wellfleet-COMMON-MIB;
wfNatBase OBJECT IDENTIFIER ::= { wfNatGroup 1 }
wfNatBaseDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'This value determines whether NAT is configured'"
DEFVAL { created }
::= { wfNatBase 1 }
wfNatBaseDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The administrative status of NAT in the router. The
value 'enabled' denotes that the NAT Process is active
on at least one interface; 'disabled' disables it on
all interfaces.'"
DEFVAL { enabled }
::= { wfNatBase 2 }
wfNatBaseState OBJECT-TYPE
SYNTAX INTEGER {
up(1),
init(2),
down(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'The state of NAT'"
DEFVAL { down }
::= { wfNatBase 3 }
wfNatBaseSoloistSlotMask OBJECT-TYPE
SYNTAX Gauge
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Slot mask for which slots the soloist gate is
eligible to run on. The MSBit represents slot
1, the next most significant bit represents slot 2,
and so on... Slots can be 1-14.
Default is all slots on a BCN."
DEFVAL { 4294705152 }
::= { wfNatBase 4 }
wfNatBaseSoloistSlot OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Slot on which NAT soloist gate is running. Slots
can be 1-14. Default is zero."
::= { wfNatBase 5 }
wfNatBaseLogMask OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A parameter to specify which NAT log messages should be logged.
Each bit represents a message as defined below. A 1 in that
bit location means to log it and a 0 means not to put that
log message in the log. Changing this value will NOT restart
NAT, but will take effct immediately(if there are any messages
to be logged.
bit 31 bit 0
+---------------------------------------+
| |
+---------------------------------------+
NAT_DBG_MIB_LOG 0x00000001
NAT_DBG_IP_LOG 0x00000002
NAT_DBG_FWD_LOG 0x00000004
NAT_DBG_MAPPING_LOG 0x00000008
NAT_DBG_AGING_LOG 0x00000010
NAT_DBG_SYNCH_LOG 0x00000020
"
DEFVAL { 0 }
::= { wfNatBase 6 }
wfNatBaseMapTimeout OBJECT-TYPE
SYNTAX INTEGER {
timeout(1),
notimeout(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This controls whether or not the dynamic mapping table
entries are aged out when unused."
DEFVAL { timeout }
::= { wfNatBase 7 }
wfNatBaseMapMaxTimeout OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum time in seconds before unused NAT mapping
table entries are deleted. This timeout or aging does
not apply to static mapping entries."
DEFVAL { 3600 }
::= { wfNatBase 8 }
wfNatBaseMapDynMapsCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of Dynamic Mappings in the dymanic mapping table"
DEFVAL { 0 }
::= { wfNatBase 9 }
wfNatBaseFtpSessionCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of FTP sessions detected on this box translated by NAT"
DEFVAL { 0 }
::= { wfNatBase 10 }
wfNatBaseNto1TrTotCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total number of active Nto1 translation counts on the box."
DEFVAL { 0 }
::= { wfNatBase 11 }
wfNatBaseSynchronization OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"`The administrative status of NAT Synchronization in the router. The
value `enabled' denotes that the NAT Synchronization is active
and is synchronizing with the peer specified in noraml conditions.; `disabled' disables it on
the box and all the peer connections will be teared down.'"
DEFVAL { disabled }
::= { wfNatBase 12 }
wfNatBaseSynRouterID OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"`This represents the Router Identifier for NAT Synchronization Only.
This is used to detect the duplicate TCP connection between peers.
The value of it can be any integer which is unique between all the NAT Syn
peers this router has. An IP Address of one of the router interfaces can be
used as the RouterID. Changing the value will result into breaking and
reconnecting using new ID with all the peers.'"
::= { wfNatBase 13 }
wfNatBaseSynPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"`This represents the TCP port on which the connection requests from the peers
will be accepted. When NAT Synchronization Protocol comes up, it will open a listen
connection for this port number. This attribute value has to be the same on all the peers
that want to make the TCP connection.'"
DEFVAL { 670 }
::= { wfNatBase 14 }
wfNatBaseSynKeepAlvInterval OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Idle session timeout period, in seconds. If an established
TCP connection remains inactive for this interval, KEEPALIVE
messages will be sent to the peer (if the Keepalive Timer is
non-zero). Setting the Idle Timer to zero disables the
keepalive feature."
DEFVAL { 120 }
::= { wfNatBase 15 }
wfNatBaseSynKeepAlvTimer OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"KEEPALIVE retransmit timeout period, in seconds. This is
the interval at which unacknowledged KEEPALIVE messages will
be retransmitted. If the Idle Timer is set to zero, this
timer ignored. If the Idle Timer is non-zero and this timer
IS zero, no KEEPALIVEs are sent and the session is terminated
upon expiration of the Idle Timer."
DEFVAL { 3 }
::= { wfNatBase 16 }
wfNatBaseSynKeepAlvRetries OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of unacknowledged KEEPALIVE messages retransmitted
before the TCP session is terminated. If this count is set
to zero, only one KEEPALIVE message will be sent."
DEFVAL { 5 }
::= { wfNatBase 17 }
wfNatAddrRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfNatAddrRangeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table of address ranges that have been designated
as the set of external apparent addresses that are
to be mapped in place of internal actual addresses.
These addresses would be the non-public reigistered
addresses."
::= { wfNatGroup 2 }
wfNatAddrRangeEntry OBJECT-TYPE
SYNTAX WfNatAddrRangeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"'Information describing each of the available address
ranges.'"
INDEX { wfNatAddrRangeAddress,
wfNatAddrRangePrefixLen }
::= { wfNatAddrRangeTable 1 }
WfNatAddrRangeEntry ::= SEQUENCE {
wfNatAddrRangeDelete
INTEGER,
wfNatAddrRangeDisable
INTEGER,
wfNatAddrRangeAddress
IpAddress,
wfNatAddrRangePrefixLen
INTEGER
}
wfNatAddrRangeDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete an address
range entry.'"
DEFVAL { created }
::= { wfNatAddrRangeEntry 1 }
wfNatAddrRangeDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable an address
range entry.'"
DEFVAL { enabled }
::= { wfNatAddrRangeEntry 2 }
wfNatAddrRangeAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The IP beginning address of this range entry."
::= { wfNatAddrRangeEntry 3 }
wfNatAddrRangePrefixLen OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The IP address mask that in conjunction with the
start address defines the address range of the entry.'"
::= { wfNatAddrRangeEntry 4 }
wfNatLocalAddrRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfNatLocalAddrRangeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table of address ranges that have been designated
as the set of local addresses that are to be mapped
via NAT."
::= { wfNatGroup 3 }
wfNatLocalAddrRangeEntry OBJECT-TYPE
SYNTAX WfNatLocalAddrRangeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"'Information describing each of the available address
ranges.'"
INDEX { wfNatLocalAddrRangeAddress,
wfNatLocalAddrRangePrefixLen }
::= { wfNatLocalAddrRangeTable 1 }
WfNatLocalAddrRangeEntry ::= SEQUENCE {
wfNatLocalAddrRangeDelete
INTEGER,
wfNatLocalAddrRangeDisable
INTEGER,
wfNatLocalAddrRangeAddress
IpAddress,
wfNatLocalAddrRangePrefixLen
INTEGER,
wfNatLocalAddrRangeNto1Addr
IpAddress
}
wfNatLocalAddrRangeDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete an address
range entry.'"
DEFVAL { created }
::= { wfNatLocalAddrRangeEntry 1 }
wfNatLocalAddrRangeDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable an address
range entry.'"
DEFVAL { enabled }
::= { wfNatLocalAddrRangeEntry 2 }
wfNatLocalAddrRangeAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The IP beginning address of this range entry."
::= { wfNatLocalAddrRangeEntry 3 }
wfNatLocalAddrRangePrefixLen OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The IP address mask that in conjunction with the
start address defines the address range of the entry.'"
::= { wfNatLocalAddrRangeEntry 4 }
wfNatLocalAddrRangeNto1Addr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Nto1 translation address used for this range."
DEFVAL { 0 }
::= { wfNatLocalAddrRangeEntry 5 }
wfNatStaticMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfNatStaticMapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"'This table creates instances of pre-defined
NAT mappings.'"
::= { wfNatGroup 4 }
wfNatStaticMapEntry OBJECT-TYPE
SYNTAX WfNatStaticMapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"'A single local-to-global address mapping.'"
INDEX { wfNatStaticMapLocalAddress,
wfNatStaticMapGlobalAddress,
wfNatStaticMapProtocol,
wfNatStaticMapLocalPort,
wfNatStaticMapGlobalPort }
::= { wfNatStaticMapTable 1 }
WfNatStaticMapEntry ::= SEQUENCE {
wfNatStaticMapDelete
INTEGER,
wfNatStaticMapDisable
INTEGER,
wfNatStaticMapLocalAddress
IpAddress,
wfNatStaticMapGlobalAddress
IpAddress,
wfNatStaticMapProtocol
INTEGER,
wfNatStaticMapLocalPort
INTEGER,
wfNatStaticMapGlobalPort
INTEGER
}
wfNatStaticMapDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete a static
address mapping entry.'"
DEFVAL { created }
::= { wfNatStaticMapEntry 1 }
wfNatStaticMapDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable a static
address mapping entry.'"
DEFVAL { enabled }
::= { wfNatStaticMapEntry 2 }
wfNatStaticMapLocalAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The local or private address of the mapping pair.'"
::= { wfNatStaticMapEntry 3 }
wfNatStaticMapGlobalAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The global or external address of the mapping pair.'"
::= { wfNatStaticMapEntry 4 }
wfNatStaticMapProtocol OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The IP protocol of the mapping pair.'"
::= { wfNatStaticMapEntry 5 }
wfNatStaticMapLocalPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The local UDP or TCP port of the mapping pair.
This will only be relevent if the protocol is
either UDP or TCP.'"
::= { wfNatStaticMapEntry 6 }
wfNatStaticMapGlobalPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The global UDP or TCP port of the mapping pair.
This will only be relevent if the protocol is
either UDP or TCP.'"
::= { wfNatStaticMapEntry 7 }
wfNatMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfNatMapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"'This table defines the current set of address
mappings that are in effect.'"
::= { wfNatGroup 5 }
wfNatMapEntry OBJECT-TYPE
SYNTAX WfNatMapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { wfNatMapLocalAddress,
wfNatMapGlobalAddress,
wfNatMapProtocol,
wfNatMapLocalPort,
wfNatMapGlobalPort }
::= { wfNatMapTable 1 }
WfNatMapEntry ::= SEQUENCE {
wfNatMapLocalAddress
IpAddress,
wfNatMapGlobalAddress
IpAddress,
wfNatMapProtocol
INTEGER,
wfNatMapLocalPort
INTEGER,
wfNatMapGlobalPort
INTEGER,
wfNatMapTxCount
Counter,
wfNatMapRxCount
Counter,
wfNatMapTimeout
Counter,
wfNatMapMode
INTEGER
}
wfNatMapLocalAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'The local address of the mapping pair.'"
::= { wfNatMapEntry 1 }
wfNatMapGlobalAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'The global address of the mapping pair.'"
::= { wfNatMapEntry 2 }
wfNatMapProtocol OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'The IP protocol of the mapping pair.'"
::= { wfNatMapEntry 3 }
wfNatMapLocalPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'When the mapping is for a TCP connection, this
denotes the TCP port number on the local side.'"
::= { wfNatMapEntry 4 }
wfNatMapGlobalPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'When the mapping is for a TCP connection, this
denotes the TCP port number on the global side.'"
::= { wfNatMapEntry 5 }
wfNatMapTxCount OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'Number of packets for this mapping pair that have
been mapped from the local to the global network.'"
::= { wfNatMapEntry 6 }
wfNatMapRxCount OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'Number of packets for this mapping pair that have
been mapped from the global to the local network.'"
::= { wfNatMapEntry 7 }
wfNatMapTimeout OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'The time in seconds since this mapping entry was
last used. This is used to age out mapping entries.'"
::= { wfNatMapEntry 8 }
wfNatMapMode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the bit mask representing the type of this
mapping. Each bit specifies the type as follows:
The mapping could be only ONE of the foolowing three...
0x01000000 - This mapping is origianted on this router,
i.e. this NAT router performed the translation
0x02000000 - This mapping is learned from the peer, i.e.
this translation was learned from the peer using
NAT Synchronization feature.
0x04000000 - This mapping is owned, i.e. it was originally
learned from peer, but this router received traffic
which used this mapping.
...and only ONE of the following three.
0x00000010 - This mapping is the STATIC mapping.
0x00000020 - This mapping is Dynamic(1 to 1) mapping.
0x00000040 - This mapping is N to 1 mapping."
DEFVAL { 0 }
::= { wfNatMapEntry 9 }
wfNatIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfNatIfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"'The set of interface that are participating
in the NAT protocol.'"
::= { wfNatGroup 6 }
wfNatIfEntry OBJECT-TYPE
SYNTAX WfNatIfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"'An single instance of a NAT interface entry.'"
INDEX { wfNatIfIpAddress,
wfNatIfCircuit }
::= { wfNatIfTable 1 }
WfNatIfEntry ::= SEQUENCE {
wfNatIfDelete
INTEGER,
wfNatIfDisable
INTEGER,
wfNatIfIpAddress
IpAddress,
wfNatIfCircuit
INTEGER,
wfNatIfType
INTEGER,
wfNatIfState
INTEGER,
wfNatIfTxCount
Counter,
wfNatIfRxCount
Counter,
wfNatIfPktDropCount
Counter
}
wfNatIfDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This variable determines in a NAT Interface has been
configured on the router."
DEFVAL { created }
::= { wfNatIfEntry 1 }
wfNatIfDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The NAT interface's administrative status. The value
'enabled' denotes that NAT has been configured
on the interface. The value 'disabled' denotes that
the interface is not running NAT.'"
DEFVAL { enabled }
::= { wfNatIfEntry 2 }
wfNatIfIpAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'The IP address of this NAT interface.'"
::= { wfNatIfEntry 3 }
wfNatIfCircuit OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The circuit number of this interface."
::= { wfNatIfEntry 4 }
wfNatIfType OBJECT-TYPE
SYNTAX INTEGER {
local(1),
global(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"'Denotes whether this interface is attached to the
local or global network.'"
DEFVAL{ local }
::= { wfNatIfEntry 5 }
wfNatIfState OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
init(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"'The state of NAT on this interface'"
DEFVAL { down }
::= { wfNatIfEntry 6 }
wfNatIfTxCount OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of packets mapped over this interface from
the local to the global network.'"
::= { wfNatIfEntry 7 }
wfNatIfRxCount OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of packets mapped over this interface from
the global to the local network.'"
::= { wfNatIfEntry 8 }
wfNatIfPktDropCount OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of packets dropped on this interface"
::= { wfNatIfEntry 9 }
wfNatSynPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfNatSynPeerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The Nat Synchronization Peer table contains configuration
and statistical information regarding this router's NAT peers"
::= { wfNatGroup 7 }
wfNatSynPeerEntry OBJECT-TYPE
SYNTAX WfNatSynPeerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the NAT Synchronization-Peer table"
INDEX { wfNatSynPeerRouterID }
::= { wfNatSynPeerTable 1 }
WfNatSynPeerEntry ::= SEQUENCE {
wfNatSynPeerDelete
INTEGER,
wfNatSynPeerDisable
INTEGER,
wfNatSynPeerState
INTEGER,
wfNatSynPeerConnType
INTEGER,
wfNatSynPeerRouterID
IpAddress,
wfNatSynPeerAddress
IpAddress,
wfNatSynPeerTransSent
INTEGER,
wfNatSynPeerTransRecd
INTEGER
}
wfNatSynPeerDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Create/Delete: if set to delete,
this instance of the peer entry is deleted,
which results into the termination of peer connection."
DEFVAL { created }
::= { wfNatSynPeerEntry 1 }
wfNatSynPeerDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable/Disable: controls whether the peer connection
is enabled or disabled, disabling this results into
the termination of TCP connection"
DEFVAL { enabled }
::= { wfNatSynPeerEntry 2 }
wfNatSynPeerState OBJECT-TYPE
SYNTAX INTEGER {
not-present(1),
init(2),
established(3),
down(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"the administrative state of the peer connection"
DEFVAL { not-present }
::= { wfNatSynPeerEntry 3 }
wfNatSynPeerConnType OBJECT-TYPE
SYNTAX INTEGER {
active(1),
passive(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"the type of the TCP connection with the peer,
whether this connection is accepted from the peer or it was
actively initialted by this router to the peer."
::= { wfNatSynPeerEntry 4}
wfNatSynPeerRouterID OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique non-zero RouterID of the peer that
this router is expecting from the connection
This is also the instance of the Peer Entry."
::= { wfNatSynPeerEntry 5}
wfNatSynPeerAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"the IP Address of the peer,
where the router will send a connect request"
::= { wfNatSynPeerEntry 6}
wfNatSynPeerTransSent OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of translations sent to this peer by the router"
::= { wfNatSynPeerEntry 7}
wfNatSynPeerTransRecd OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of translations received from this peer by the router"
::= { wfNatSynPeerEntry 8}
END