Wellfleet-SDLC-MIB DEFINITIONS ::= BEGIN
IMPORTS
Counter, TimeTicks
FROM RFC1155-SMI
OBJECT-TYPE
FROM RFC-1212
DisplayString
FROM RFC1213-MIB
wfSdlcGroup
FROM Wellfleet-COMMON-MIB;
wfSdlc OBJECT IDENTIFIER ::= { wfSdlcGroup 1 }
wfSdlcDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete SDLC."
DEFVAL { created }
::= { wfSdlc 1 }
wfSdlcDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable SDLC."
DEFVAL { enabled }
::= { wfSdlc 2 }
wfSdlcState OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
init(3),
notpresent(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current state of SDLC."
DEFVAL { down }
::= { wfSdlc 3 }
wfSdlcPortAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfSdlcPortAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"-- THE SDLC PORT ADMINISTRATIVE TABLE
'This table contains objects that can be changed to manage an SDLC port.
Changing one of these parameters take effect in the operating port
immediately or may wait until the interface is restarted depending on
the object. Most of the objects in this read-write table have
corresponding read-only objects in the wfSdlcPortOperTable that return
the current opeating value. The operating values may be different from
these configured values if a configured parameter was changed after the
interface was started."
::= { wfSdlcGroup 2 }
wfSdlcPortAdminEntry OBJECT-TYPE
SYNTAX WfSdlcPortAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of configured values for an SDLC port"
INDEX { wfSdlcPortAdminIndex }
::= { wfSdlcPortAdminTable 1 }
WfSdlcPortAdminEntry ::= SEQUENCE {
wfSdlcPortAdminDelete
INTEGER,
wfSdlcPortAdminDisable
INTEGER,
wfSdlcPortAdminIndex
INTEGER,
wfSdlcPortAdminAddress4
DisplayString,
wfSdlcPortAdminType
INTEGER,
wfSdlcPortAdminTopology
INTEGER,
wfSdlcPortAdminACTIVTO
INTEGER,
wfSdlcPortAdminPAUSE
INTEGER,
wfSdlcPortAdminCredit
INTEGER,
wfSdlcPortAdminIdleTimer
INTEGER,
wfSdlcPortAdminIdleRetry
INTEGER,
wfSdlcPortAdminNPRcvTimer
INTEGER,
wfSdlcPortAdminNPRcvRetry
INTEGER,
wfSdlcPortAdminWriteTimer
INTEGER,
wfSdlcPortAdminWriteRetry
INTEGER,
wfSdlcPortAdminLinkConnTimer
INTEGER,
wfSdlcPortAdminLinkConnRetry
INTEGER,
wfSdlcPortAdminPriFdplx
INTEGER,
wfSdlcPortAdminSecFdplx
INTEGER,
wfSdlcPortAdminUseRej
INTEGER,
wfSdlcPortAdminPortType
INTEGER,
wfSdlcPortAdminMaxXidSize
INTEGER,
wfSdlcPortAdminMaxRetryCount
INTEGER,
wfSdlcPortAdminMaxFrameSize
INTEGER,
wfSdlcPortAdminDlcName8
DisplayString,
wfSdlcPortAdminCpType
INTEGER,
wfSdlcPortAdminLsRole
INTEGER,
wfSdlcPortAdminPortNumber
INTEGER,
wfSdlcPortAdminLsAddress
INTEGER,
wfSdlcPortAdminTotLsActLim
INTEGER,
wfSdlcPortAdminInLsActLim
INTEGER,
wfSdlcPortAdminOutLsActLim
INTEGER,
wfSdlcPortAdminNegLsSupp
INTEGER,
wfSdlcPortAdminRcvPoolSize
INTEGER,
wfSdlcPortAdminStatsColl
INTEGER,
wfSdlcPortAdminDebugFlg
INTEGER
}
wfSdlcPortAdminDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Create/Delete Port"
DEFVAL { created }
::= { wfSdlcPortAdminEntry 1 }
wfSdlcPortAdminDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable/Disable Port"
DEFVAL { enabled }
::= { wfSdlcPortAdminEntry 2 }
wfSdlcPortAdminIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port.This is equivalent to the circuit
number for this interface."
::= { wfSdlcPortAdminEntry 3 }
wfSdlcPortAdminAddress4 OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A string of 4 bytes that defines the physical port to which this
interface is assigned. Its value shall be unique within the administered
system. It must contain only ASCII printable characters.
A write operation shall not take effect until the port is cycled
inactive."
::= { wfSdlcPortAdminEntry 4 }
wfSdlcPortAdminType OBJECT-TYPE
SYNTAX INTEGER {
leased(1),
switched(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is to connect to a
leased or switched line. A write operation to this administrative
value shall not take effect until the SDLC port has been cycled
inactive."
DEFVAL { leased }
::= { wfSdlcPortAdminEntry 5 }
wfSdlcPortAdminTopology OBJECT-TYPE
SYNTAX INTEGER {
ptop(1),
multipoint(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is to operate in a
point-to-point or multidropped topology. A write operation to this
administrative value shall not take effect until the SDLC port has
been cycled inactive."
DEFVAL { ptop }
::= { wfSdlcPortAdminEntry 6 }
wfSdlcPortAdminACTIVTO OBJECT-TYPE
SYNTAX INTEGER(0..120)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter defines the period of time, in seconds,(0....120)
the port will allow a switched line to remain inactive ( no I-Frames)
before disconnecting. A value of zero indicates no timeout.
A write operation to this administered value will not take effect until
the port is cycled inactive."
DEFVAL { 15 }
::= { wfSdlcPortAdminEntry 7 }
wfSdlcPortAdminPAUSE OBJECT-TYPE
SYNTAX INTEGER(1..600)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object defines the minimum elapsed time, (1.......600)
in tenths of seconds, between any two traversals of the poll list
for a primary SDLC port. This object has meaning for primary SDLC
ports only. A write operation to this administered value will not
take effect until the port is cycled inactive."
DEFVAL { 20 }
::= { wfSdlcPortAdminEntry 8 }
wfSdlcPortAdminCredit OBJECT-TYPE
SYNTAX INTEGER(1..50)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This field is used to regulate the flow of data from the DLC
Interface to the DLC client."
DEFVAL { 7 }
::= { wfSdlcPortAdminEntry 9 }
wfSdlcPortAdminIdleTimer OBJECT-TYPE
SYNTAX INTEGER(1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This timer is used as a 'watch-dog' for a completely inactive line. The
timer is specified in milliseconds."
DEFVAL { 6000 }
::= { wfSdlcPortAdminEntry 10 }
wfSdlcPortAdminIdleRetry OBJECT-TYPE
SYNTAX INTEGER(1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of times to rerun the idle timer before failure."
DEFVAL { 20 }
::= { wfSdlcPortAdminEntry 11 }
wfSdlcPortAdminNPRcvTimer OBJECT-TYPE
SYNTAX INTEGER(1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Non-Productive receive timeout corresponds to the time allowed for
receipt of a valid frame from the secondary. The timer is specified in
milliseconds."
DEFVAL { 2000 }
::= { wfSdlcPortAdminEntry 12 }
wfSdlcPortAdminNPRcvRetry OBJECT-TYPE
SYNTAX INTEGER(1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Non-Productive receive retry limit is used in conjunction with the
timeout value to provide the overall time before an outage message is issued."
DEFVAL { 15 }
::= { wfSdlcPortAdminEntry 13 }
wfSdlcPortAdminWriteTimer OBJECT-TYPE
SYNTAX INTEGER(1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum amount of time allowed to transmit a complete frame.
The timer is specified in milliseconds."
DEFVAL { 3000 }
::= { wfSdlcPortAdminEntry 14 }
wfSdlcPortAdminWriteRetry OBJECT-TYPE
SYNTAX INTEGER(1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The write timer retry limit is used in conjunction with the timeout value
to provide the overall time before an outage message is issued."
DEFVAL { 10 }
::= { wfSdlcPortAdminEntry 15 }
wfSdlcPortAdminLinkConnTimer OBJECT-TYPE
SYNTAX INTEGER(1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Link connection timeout together with the retry limit corresponds to
the time interval spent waiting. The timer is specified
in milliseconds."
DEFVAL { 3000 }
::= { wfSdlcPortAdminEntry 16 }
wfSdlcPortAdminLinkConnRetry OBJECT-TYPE
SYNTAX INTEGER(1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Link connection retry limit specifies the number of times the link has
been tested for a connection before it fails the pending activate port request.'"
DEFVAL { 10 }
::= { wfSdlcPortAdminEntry 17 }
wfSdlcPortAdminPriFdplx OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary SDLC station is full-duplex or not"
DEFVAL { false }
::= { wfSdlcPortAdminEntry 18 }
wfSdlcPortAdminSecFdplx OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secondary SDLC station is full-duplex or not"
DEFVAL { false }
::= { wfSdlcPortAdminEntry 19 }
wfSdlcPortAdminUseRej OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Whether REJ are in use for out of sequence I-frames"
DEFVAL { true }
::= { wfSdlcPortAdminEntry 20 }
wfSdlcPortAdminPortType OBJECT-TYPE
SYNTAX INTEGER {
leased(1),
dialout(2),
autoanswer(3),
autoanswerdialout(4),
mandialout(5),
mananswer(6),
mananswerdialout(7)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Type of port
1 - Leased Line
2 - Switched Line with dial out capabilities
3 - Switched Line with auto answer capabilities
4 - Switched Line with auto answer and dial out capabilities
5 - Switched Line with manual dial out capabilities
6 - Switched Line with manual answer capabilities
7 - Switched Line with manual answer and dial out capabilities "
DEFVAL { leased }
::= { wfSdlcPortAdminEntry 21 }
wfSdlcPortAdminMaxXidSize OBJECT-TYPE
SYNTAX INTEGER(0..256)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Maximum XID size"
DEFVAL { 256 }
::= { wfSdlcPortAdminEntry 22 }
wfSdlcPortAdminMaxRetryCount OBJECT-TYPE
SYNTAX INTEGER(1..7)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Maximum number of times that a frame can be retransmitted."
DEFVAL { 5 }
::= { wfSdlcPortAdminEntry 23 }
wfSdlcPortAdminMaxFrameSize OBJECT-TYPE
SYNTAX INTEGER {
pdu0265(265),
pdu0521(521),
pdu1033(1033),
pdu2057(2057),
pdu4105(4105)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Maximum frame size supported by this DLC."
DEFVAL { pdu1033 }
::= { wfSdlcPortAdminEntry 24 }
wfSdlcPortAdminDlcName8 OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A string of 8 bytes that names this DLC. Its value shall
be unique within the administered system. It must contain only
ASCII printable characters. A write operation shall not take effect
until the port is cycled inactive."
::= { wfSdlcPortAdminEntry 25 }
wfSdlcPortAdminCpType OBJECT-TYPE
SYNTAX INTEGER {
learn(1),
len(2),
network(3),
end(4),
vrn(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"type of CP
1 - LEARN NODE
2 - LEN NODE
3 - NETWORK NODE
2 - END NODE
5 - VRN NODE "
DEFVAL { network }
::= { wfSdlcPortAdminEntry 26 }
wfSdlcPortAdminLsRole OBJECT-TYPE
SYNTAX INTEGER {
neg(1),
pri(2),
sec(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Link Station Role
1 - Negotiable
2 - Primary
3 - Secondary "
DEFVAL { pri }
::= { wfSdlcPortAdminEntry 27 }
wfSdlcPortAdminPortNumber OBJECT-TYPE
SYNTAX INTEGER(1..2048)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Port Number, unique within this system."
DEFVAL { 1 }
::= { wfSdlcPortAdminEntry 28 }
wfSdlcPortAdminLsAddress OBJECT-TYPE
SYNTAX INTEGER(1..254)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Link Station Address. This object has meaning if this
link station is a secondary link station."
DEFVAL { 2 }
::= { wfSdlcPortAdminEntry 29 }
wfSdlcPortAdminTotLsActLim OBJECT-TYPE
SYNTAX INTEGER(1..254)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Total link station activation limit."
DEFVAL { 16 }
::= { wfSdlcPortAdminEntry 30 }
wfSdlcPortAdminInLsActLim OBJECT-TYPE
SYNTAX INTEGER(1..254)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Inbound link station activation limit."
DEFVAL { 8 }
::= { wfSdlcPortAdminEntry 31 }
wfSdlcPortAdminOutLsActLim OBJECT-TYPE
SYNTAX INTEGER(1..254)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Outbound link station activation limit."
DEFVAL { 8 }
::= { wfSdlcPortAdminEntry 32 }
wfSdlcPortAdminNegLsSupp OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Whether the DLC supports Negoatible connections"
DEFVAL { false }
::= { wfSdlcPortAdminEntry 33 }
wfSdlcPortAdminRcvPoolSize OBJECT-TYPE
SYNTAX INTEGER(1..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Receive Buffer pool size."
DEFVAL { 7 }
::= { wfSdlcPortAdminEntry 34 }
wfSdlcPortAdminStatsColl OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Whether Stats collection is turned on for this port."
DEFVAL { true }
::= { wfSdlcPortAdminEntry 35 }
wfSdlcPortAdminDebugFlg OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Debug Flag, Enables/Disables debug log messages."
DEFVAL { disabled }
::= { wfSdlcPortAdminEntry 36 }
wfSdlcPortOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfSdlcPortOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains current SDLC port parameters. Many of
these objects have corresponding objects inthe wfSdlcPortAdmnTable."
::= { wfSdlcGroup 3 }
wfSdlcPortOperEntry OBJECT-TYPE
SYNTAX WfSdlcPortOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Currently set parameters for a specific SDLC port"
INDEX { wfSdlcPortOperIndex }
::= { wfSdlcPortOperTable 1 }
WfSdlcPortOperEntry ::= SEQUENCE {
wfSdlcPortOperIndex
INTEGER,
wfSdlcPortOperAddress4
DisplayString,
wfSdlcPortOperRole
INTEGER,
wfSdlcPortOperType
INTEGER,
wfSdlcPortOperTopology
INTEGER,
wfSdlcPortOperACTIVTO
INTEGER,
wfSdlcPortOperPAUSE
INTEGER,
wfSdlcPortOperSlowPollMethod
INTEGER,
wfSdlcPortOperSlowPollTimer
TimeTicks,
wfSdlcPortOperAbmSuppInd
INTEGER,
wfSdlcPortOperSimRimSupp
INTEGER,
wfSdlcPortOperSecInitNonactSupp
INTEGER
}
wfSdlcPortOperIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port. This value reflects the
circuit number for this interface."
::= { wfSdlcPortOperEntry 1 }
wfSdlcPortOperAddress4 OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An octet string that describes the physical port to which
this interface is currently attached."
::= { wfSdlcPortOperEntry 2 }
wfSdlcPortOperRole OBJECT-TYPE
SYNTAX INTEGER {
sec(1),
pri(2),
neg(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Link Station Role
1 - Secondary
2 - Primary
4 - Negotiable"
DEFVAL { pri }
::= { wfSdlcPortOperEntry 3 }
wfSdlcPortOperType OBJECT-TYPE
SYNTAX INTEGER {
leased(1),
switched(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is currently
operating as though connected to a leased or switched line."
DEFVAL { leased }
::= { wfSdlcPortOperEntry 4 }
wfSdlcPortOperTopology OBJECT-TYPE
SYNTAX INTEGER {
ptop(1),
multipoint(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is currently
operating in a point-to-point or multi dropped topology."
DEFVAL { multipoint }
::= { wfSdlcPortOperEntry 5 }
wfSdlcPortOperACTIVTO OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This parameter describes the period of time, in seconds,
the port will allow a switched line to remain inactive
( no I-Frames) before disconnecting. A value of zero indicates
no timeout."
::= { wfSdlcPortOperEntry 6 }
wfSdlcPortOperPAUSE OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the current minimum elapsed time, in
tenths of seconds, between any two traversals of the poll list
for a primary SDLC port. This object has meaning for primary
SDLC ports only."
::= { wfSdlcPortOperEntry 7 }
wfSdlcPortOperSlowPollMethod OBJECT-TYPE
SYNTAX INTEGER {
servlim(1),
pause(2),
other(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object defines the exact method that is in effect for
periodically polling failed secondary link station addresses."
DEFVAL { pause }
::= { wfSdlcPortOperEntry 8 }
wfSdlcPortOperSlowPollTimer OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in 1/100ths of seconds,
between polls for failed secondary link station addresses."
::= { wfSdlcPortOperEntry 9 }
wfSdlcPortOperAbmSuppInd OBJECT-TYPE
SYNTAX INTEGER {
supported(1),
notsupported(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Specifies whether Asynchronous Balanced Mode is supported."
DEFVAL { notsupported }
::= { wfSdlcPortOperEntry 10 }
wfSdlcPortOperSimRimSupp OBJECT-TYPE
SYNTAX INTEGER {
supported(1),
notsupported(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Specifies whether SDLC RIM or SIM initialization options
are supported."
DEFVAL { supported }
::= { wfSdlcPortOperEntry 11 }
wfSdlcPortOperSecInitNonactSupp OBJECT-TYPE
SYNTAX INTEGER {
supported(1),
notsupported(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Specifies whether secondary-initiated nonactivation XID
support is provided."
DEFVAL { notsupported }
::= { wfSdlcPortOperEntry 12 }
wfSdlcPortStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfSdlcPortStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"-- This table shall keep only physical statistics about a port.
'Each entry in this table contains statistics for a specific
SDLC port."
::= { wfSdlcGroup 4 }
wfSdlcPortStatsEntry OBJECT-TYPE
SYNTAX WfSdlcPortStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of statistics for an SDLC port"
INDEX { wfSdlcPortStatsIndex }
::= { wfSdlcPortStatsTable 1 }
WfSdlcPortStatsEntry ::= SEQUENCE {
wfSdlcPortStatsIndex
INTEGER,
wfSdlcPortStatsDwarfFrames
INTEGER
}
wfSdlcPortStatsIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port."
::= { wfSdlcPortStatsEntry 1 }
wfSdlcPortStatsDwarfFrames OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total number of frames received by this
port which were delivered intact by the physical layer but were too
short to be legal."
::= { wfSdlcPortStatsEntry 2 }
wfSdlcLSAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfSdlcLSAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The following classes of information is modelled for each SDLC
link station:
--
-- 1. ADMINISTRATIVE ( read/write)
-- 2. OPERATIONAL ( read-only)
-- 3. STATISTICS ( read-only)
--
-- THE SDLC LINK STATION ADMINISTRATIVE TABLE
'This table contains objects that can be changed to manage an
SDLC link station. These parameters are per Link Station. Changing
one of these parameters may take effect in the operating link
immediately or may wait until the link is restarted depending on the
object. Most of the objects in this read-write table have
corresponding read-only objects in the wfSdlcLSOperTable that return
the current operating value. The operating values may be different
from these configured values if changed by XID negotiation or if a
configured parameter was changed after the link was started."
::= { wfSdlcGroup 5 }
wfSdlcLSAdminEntry OBJECT-TYPE
SYNTAX WfSdlcLSAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of configured values for an SDLC link"
INDEX { wfSdlcLSAdminIfIndex,
wfSdlcLSAdminAddress }
::= { wfSdlcLSAdminTable 1 }
WfSdlcLSAdminEntry ::= SEQUENCE {
wfSdlcLSAdminDelete
INTEGER,
wfSdlcLSAdminDisable
INTEGER,
wfSdlcLSAdminIfIndex
INTEGER,
wfSdlcLSAdminAddress
INTEGER,
wfSdlcLSAdminGroupAddress
INTEGER,
wfSdlcLSAdminRole
INTEGER,
wfSdlcLSAdminMAXDATA
INTEGER,
wfSdlcLSAdminREPLYTO
INTEGER,
wfSdlcLSAdminMAXIN
INTEGER,
wfSdlcLSAdminMAXOUT
INTEGER,
wfSdlcLSAdminMODULO
INTEGER,
wfSdlcLSAdminRETRIESm
INTEGER,
wfSdlcLSAdminRETRIESt
INTEGER,
wfSdlcLSAdminRETRIESn
INTEGER,
wfSdlcLSAdminRNRLIMIT
INTEGER,
wfSdlcLSAdminContTimer
INTEGER,
wfSdlcLSAdminContTimerRetry
INTEGER,
wfSdlcLSAdminContTimer2
INTEGER,
wfSdlcLSAdminContTimer2Retry
INTEGER,
wfSdlcLSAdminDiscTimer
INTEGER,
wfSdlcLSAdminDiscTimerRetry
INTEGER,
wfSdlcLSAdminNvePollTimer
INTEGER,
wfSdlcLSAdminNvePollTimerRetry
INTEGER,
wfSdlcLSAdminNvePollTimer2
INTEGER,
wfSdlcLSAdminNvePollTimer2Retry
INTEGER,
wfSdlcLSAdminNoRespTimerRetry
INTEGER,
wfSdlcLSAdminRemBusyTimerRetry
INTEGER,
wfSdlcLSAdminRRTimer
INTEGER,
wfSdlcLSAdminGpAddName
DisplayString,
wfSdlcLSAdminPollFrame
INTEGER,
wfSdlcLSAdminPollOnIframe
INTEGER,
wfSdlcLSAdminLinkStationName
DisplayString,
wfSdlcLSAdminAdjNodeType
INTEGER,
wfSdlcLSAdminSimRim
INTEGER
}
wfSdlcLSAdminDelete OBJECT-TYPE
SYNTAX INTEGER {
created(1),
deleted(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Create/Delete Link Station"
DEFVAL { created }
::= { wfSdlcLSAdminEntry 1 }
wfSdlcLSAdminDisable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the desired state of the SDLC station."
DEFVAL { enabled }
::= { wfSdlcLSAdminEntry 2 }
wfSdlcLSAdminIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port which owns this link station.
This is equivalent to the circuit number for this interface."
::= { wfSdlcLSAdminEntry 3 }
wfSdlcLSAdminAddress OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the poll address of the secondary link station for
this SDLC link. It uniquely identifies the SDLC link station within a
single SDLC port."
::= { wfSdlcLSAdminEntry 4 }
wfSdlcLSAdminGroupAddress OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value is the group poll address of the secondary link station for
this SDLC link. If this link station is not part of a group, this address
will be NULL."
::= { wfSdlcLSAdminEntry 5 }
wfSdlcLSAdminRole OBJECT-TYPE
SYNTAX INTEGER {
negot(1),
primary(2),
sec(3),
msec(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the role that the link station shall assume
the next time a connection is established."
DEFVAL { primary }
::= { wfSdlcLSAdminEntry 6 }
wfSdlcLSAdminMAXDATA OBJECT-TYPE
SYNTAX INTEGER {
pdu0265(265),
pdu0521(521),
pdu1033(1033),
pdu2057(2057),
pdu4105(4105)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the maximum PDU size allowed for the logical
link. This value includes the Transmission Header (TH) and Request
Header (RH). A write operation to this administrative value will not
change the operational value, wfSdlcLSOperMAXDATA, until the link
station hasbeen cycled inactive."
DEFVAL { pdu1033 }
::= { wfSdlcLSAdminEntry 7 }
wfSdlcLSAdminREPLYTO OBJECT-TYPE
SYNTAX INTEGER(1..600)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the reply timeout, in tenths of seconds,
(1....600) for an SDLC link station. If the link station does not
receive a repsonse to a poll or message before the specified time
expires then the appropriate error recovery shall be initiated. A
write operation to this administered value will not change the
operational value, wfSdlcLSOperREPLYTO, until the link station is
cycled inactive. This object has no meaning for secondary SDLC link
stations."
DEFVAL { 30 }
::= { wfSdlcLSAdminEntry 8 }
wfSdlcLSAdminMAXIN OBJECT-TYPE
SYNTAX INTEGER(1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the maximum number, (1.....127) of
unacknowledged frames which an SDLC link station may receive. This
will range from one to modulus minus one. The modulus is controlled
by the object: wfSdlcLSAdminModulus. A write operation to this
administered value will not change the operational value,
wfSdlcLSOperMAXIN, until the link station is cycled inactive."
DEFVAL { 7 }
::= { wfSdlcLSAdminEntry 9 }
wfSdlcLSAdminMAXOUT OBJECT-TYPE
SYNTAX INTEGER(1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the maximum consequetive unacknowledged
frames, (1.....127) which an SDLC link station shall send without
an acknowledgement. This shall range from one to modulus minus one.
The modulus is controlled by the object: wfSdlcLSAdminMODULO. A
write operation to this administered value will not change the
operational value, wfSdlcLSOperMAXOUT, until the link station is
cycled inactive."
DEFVAL { 7 }
::= { wfSdlcLSAdminEntry 10 }
wfSdlcLSAdminMODULO OBJECT-TYPE
SYNTAX INTEGER {
default(8),
extended(128)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the modulus, (8,128) for an SDLC link
station. This modulus determines the size of the rotating
acknowledgement window used the SDLC link station pair A write
operation to this administered value will not change the operational
value, wfSdlcLSOperMAXOUT, until the link station is cycled inactive."
DEFVAL { default }
::= { wfSdlcLSAdminEntry 11 }
wfSdlcLSAdminRETRIESm OBJECT-TYPE
SYNTAX INTEGER(1..600)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls number of retries, ( 1.....128) in a retry
sequence for an SDLC link station. A retry sequence is a series of
retransmitted frames ( data or control) for which no positive
acknowledgement is received. The number of times that the retry
sequence is to be repeated is controlled by the object:
wfSdlcLSOperRETRIESn. The interval between retry sequences is
controlled by the object: wfSdlcLSOperRETRIESt. A write operation to
this administered value will not change the operational value,
wfSdlcLSOperRETRIESm, until the link station is cycled inactive."
DEFVAL { 20 }
::= { wfSdlcLSAdminEntry 12 }
wfSdlcLSAdminRETRIESt OBJECT-TYPE
SYNTAX INTEGER(0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the interval, in seconds, (0....255) between
retry sequences for an SDLC link station if multiple retry sequences
are specified . A retry sequence is a series of retransmitted frames
( data or control) for which no positive acknowledgement is received.
The number of repeated retries sequences is controlled by the object:
wfSdlcLSAdminRETRIESn. The retries per sequence is controlled by the
object: wfSdlcLSAdminRETRIESm. A write operation to this administered
value will not change the operational value, wfSdlcLSOperRETRIESt,
until the link station is cycled inactive."
DEFVAL { 2 }
::= { wfSdlcLSAdminEntry 13 }
wfSdlcLSAdminRETRIESn OBJECT-TYPE
SYNTAX INTEGER(1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times, (1....127) that a retry
sequence is repeated for an SDLC link station. A retry sequence is a
series of retransmitted frames ( data or control) for which no positive
acknowledgement is received. The interval between retry sequences is
controlled by the object: wfSdlcLSAdminRETRIESn. The retries per
sequence is controlled by the object: wfSdlcLSAdminRETRIESm. A write
operation to this administered value will not change the operational
value, wfSdlcLSOperRETRIESn, until the link station is cycled
inactive."
DEFVAL { 4 }
::= { wfSdlcLSAdminEntry 14 }
wfSdlcLSAdminRNRLIMIT OBJECT-TYPE
SYNTAX INTEGER(1..90)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the length of time, in minutes, (1.....90)
that an SDLC link station will allow its adjacent link station to
remain in a busy (RNR) state before declaring it inoperative. A write
operation to this administered value will not change the operational
value, wfSdlcLSOperRNRLIMIT, until the link station is cycled
inactive."
DEFVAL { 3 }
::= { wfSdlcLSAdminEntry 15 }
wfSdlcLSAdminContTimer OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the timeout required before a SNRM or XID
is retransmitted in the event of non-acknowledgement. Used for
Primary SDLC only. The value must be greater then the no response
(T1) timeout value (no_resp_timer) The timer is specified in
milliseconds."
DEFVAL { 4000 }
::= { wfSdlcLSAdminEntry 16 }
wfSdlcLSAdminContTimerRetry OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times transmission and
retransmission of a contact frame (e.g. SNRM) is allowed before
switching to the slow
poll timer."
DEFVAL { 4 }
::= { wfSdlcLSAdminEntry 17 }
wfSdlcLSAdminContTimer2 OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the slow poll contact timer in milliseconds.
When the contact timer retry count expires, polling will continue
using this timer."
DEFVAL { 4000 }
::= { wfSdlcLSAdminEntry 18 }
wfSdlcLSAdminContTimer2Retry OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times transmission and
retransmission of a contact frame (e.g. SNRM) is allowed before
an outage message is sent to the DLC user."
DEFVAL { 8 }
::= { wfSdlcLSAdminEntry 19 }
wfSdlcLSAdminDiscTimer OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the time in milliseconds before a DISC
is retransmitted in the event of non-acknowledgement
(for primary SDLC only)."
DEFVAL { 4000 }
::= { wfSdlcLSAdminEntry 20 }
wfSdlcLSAdminDiscTimerRetry OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times transmission and
retransmission of a DISC is allowed."
DEFVAL { 4 }
::= { wfSdlcLSAdminEntry 21 }
wfSdlcLSAdminNvePollTimer OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the timeout required before an adjacent
secondary station is re-inserted into the polling list after
being removed for non-response. The time is specified in
milliseconds."
DEFVAL { 400 }
::= { wfSdlcLSAdminEntry 22 }
wfSdlcLSAdminNvePollTimerRetry OBJECT-TYPE
SYNTAX INTEGER(1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times a station is removed
from the polling list on the normal poll timer before switching
to the slow poll timer."
DEFVAL { 16 }
::= { wfSdlcLSAdminEntry 23 }
wfSdlcLSAdminNvePollTimer2 OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The slow negative poll timer in milliseconds. When the negative
poll timer count expires, the poll will continue by using this
timer."
DEFVAL { 1000 }
::= { wfSdlcLSAdminEntry 24 }
wfSdlcLSAdminNvePollTimer2Retry OBJECT-TYPE
SYNTAX INTEGER(1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times a station is removed
from the polling list before an outage message is sent to a client."
DEFVAL { 65535 }
::= { wfSdlcLSAdminEntry 25 }
wfSdlcLSAdminNoRespTimerRetry OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times an adjacent secondary
station is seen to fail to respond before an outage message is sent
to a client."
DEFVAL { 10 }
::= { wfSdlcLSAdminEntry 26 }
wfSdlcLSAdminRemBusyTimerRetry OBJECT-TYPE
SYNTAX INTEGER(1..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Remote busy retry limit value is user with the timeout
value to provide the overall timeout before an outage message
is sent to a client."
DEFVAL { 4 }
::= { wfSdlcLSAdminEntry 27 }
wfSdlcLSAdminRRTimer OBJECT-TYPE
SYNTAX INTEGER(0..64000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The RR Turn-around timer is in milliseconds. It is the time
that DLC waits before turning the poll bit around when it has
no work to do."
::= { wfSdlcLSAdminEntry 28 }
wfSdlcLSAdminGpAddName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The address of the group to which this link station belongs.
This object is only used in association with group polling.
It is 4 bytes of ASCII."
::= { wfSdlcLSAdminEntry 29 }
wfSdlcLSAdminPollFrame OBJECT-TYPE
SYNTAX INTEGER {
disc(83),
snrm(147),
xid(191),
snrme(223),
test(243)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The frame to use for pre-activation polling. This is normally
set to XID to show that polling is in the control of the DLC user."
DEFVAL { xid }
::= { wfSdlcLSAdminEntry 30 }
wfSdlcLSAdminPollOnIframe OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Flag whether this link station is permitted to send the poll bit
on an I-frame. Certain SDLC implementations do not handle receipt of
I-frames carrying the poll bit."
DEFVAL { true }
::= { wfSdlcLSAdminEntry 31 }
wfSdlcLSAdminLinkStationName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The name of the adjacent link station in ASCII. Used for stats
and Alert messages to uniquely identify the station. 8 BYTES in
length."
::= { wfSdlcLSAdminEntry 32 }
wfSdlcLSAdminAdjNodeType OBJECT-TYPE
SYNTAX INTEGER {
learn(1),
len(2),
network(3),
end(4),
vrn(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Adjacent Node type"
DEFVAL { network }
::= { wfSdlcLSAdminEntry 33 }
wfSdlcLSAdminSimRim OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the support for transmission and receipt
of SIM and RIM control frames for this link station."
DEFVAL { false }
::= { wfSdlcLSAdminEntry 34 }
wfSdlcLSOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfSdlcLSOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains current SDLC link parameters. Many of
these objects have corresponding objects in the wfSdlcLSAdmnTable."
::= { wfSdlcGroup 6 }
wfSdlcLSOperEntry OBJECT-TYPE
SYNTAX WfSdlcLSOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of current SDLC link parameters"
INDEX { wfSdlcLSOperIfIndex,
wfSdlcLSOperAddress }
::= { wfSdlcLSOperTable 1 }
WfSdlcLSOperEntry ::= SEQUENCE {
wfSdlcLSOperIfIndex
INTEGER,
wfSdlcLSOperAddress
INTEGER,
wfSdlcLSOperRole
INTEGER,
wfSdlcLSOperState
INTEGER,
wfSdlcLSOperMAXDATA
INTEGER,
wfSdlcLSOperREPLYTO
INTEGER,
wfSdlcLSOperMAXIN
INTEGER,
wfSdlcLSOperMAXOUT
INTEGER,
wfSdlcLSOperMODULO
INTEGER,
wfSdlcLSOperRETRIESm
INTEGER,
wfSdlcLSOperRETRIESt
INTEGER,
wfSdlcLSOperRETRIESn
INTEGER,
wfSdlcLSOperRNRLIMIT
INTEGER,
wfSdlcLSOperDATMODE
INTEGER,
wfSdlcLSOperCreateTime
TimeTicks,
wfSdlcLSOperLastFailCause
INTEGER,
wfSdlcLSOperLastFailCtrlIn2
OCTET STRING,
wfSdlcLSOperLastFailCtrlOut2
OCTET STRING,
wfSdlcLSOperLastFailFRMRInfo5
OCTET STRING,
wfSdlcLSOperLastFailREPLYTOs
Counter,
wfSdlcLSOperGroupAddress
INTEGER
}
wfSdlcLSOperIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port which owns this link station."
::= { wfSdlcLSOperEntry 1 }
wfSdlcLSOperAddress OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the poll address of the secondary link station
in this SDLC link. It uniquely identifies the SDLC link station
within a single SDLC port."
::= { wfSdlcLSOperEntry 2 }
wfSdlcLSOperRole OBJECT-TYPE
SYNTAX INTEGER {
negot(1),
primary(2),
sec(3),
msec(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current role that the link station
is assuming."
DEFVAL { sec }
::= { wfSdlcLSOperEntry 3 }
wfSdlcLSOperState OBJECT-TYPE
SYNTAX INTEGER {
discont(1),
conpend(2),
contact(3),
dispend(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the operational state of the SDLC link
station. The managed system shall attempt to keep this value
consistent with the administered state."
DEFVAL { discont }
::= { wfSdlcLSOperEntry 4 }
wfSdlcLSOperMAXDATA OBJECT-TYPE
SYNTAX INTEGER {
pdu0265(265),
pdu0521(521),
pdu1033(1033),
pdu2057(2057),
pdu4105(4105)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current maximum PDU size allowed
for the logical link. This value includes the Transmission Header
(TH) and Request Header (RH). This value will controlled by the
administered MAXDATA, wfSdlcLSAdminMAXDATA, or by the value negotiated
in the XID exchange for link stations on a switched
SDLC line."
DEFVAL { pdu1033 }
::= { wfSdlcLSOperEntry 5 }
wfSdlcLSOperREPLYTO OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current reply timeout, in tenths of
seconds, for an SDLC link station. If the link station does not
receive a repsonse to a poll or message before the specified time
expires then the appropriate error recovery shall be initiated.
This object has no meaning for secondary SDLC link stations."
::= { wfSdlcLSOperEntry 6 }
wfSdlcLSOperMAXIN OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current maximum number of
unacknowledged frames which an SDLC link station may receive.
This shall range from one to modulus minus one."
::= { wfSdlcLSOperEntry 7 }
wfSdlcLSOperMAXOUT OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object controls the maximum consequetive unacknowledged
frames which an SDLC link station shall send without an
acknowledgement. This shall range from one to modulus minus one.
The modulus is controlled by the object: wfSdlcLSAdminMODULO.
This value will controlled by the administered MAXOUT,
wfSdlcLSAdminMAXOUT, or by the value negotiated in the XID exchange
for link stations on a switched SDLC line."
::= { wfSdlcLSOperEntry 8 }
wfSdlcLSOperMODULO OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current modulus for an SDLC link
station. This modulus determines the size of rotating acknowledgement
window used by the SDLC link station pair."
::= { wfSdlcLSOperEntry 9 }
wfSdlcLSOperRETRIESm OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object controls number of retries in a retry sequence
for an SDLC link station. A retry sequence is a series of
retransmitted frames ( data or control) for which no positive
acknowledgement is received. The current number of times that the
retry sequence is to be repeated is reflected by the object:
wfSdlcLSOperRETRIESn. The current interval between retry sequences
is reflected by the object: wfSdlcLSOperRETRIESt."
::= { wfSdlcLSOperEntry 10 }
wfSdlcLSOperRETRIESt OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current interval, in seconds, between
retry sequences for an SDLC link station if multiple retry sequences
are specified. A retry sequence is a series of retransmitted frames
( data or control) for which no positive acknowledgement is received.
The current number of repeated retries sequences is reflected by the
object: wfSdlcLSOperRETRIESn. The current retries per sequence is
reflected by the object: wfSdlcLSOperRETRIESm."
::= { wfSdlcLSOperEntry 11 }
wfSdlcLSOperRETRIESn OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current number of times that a retry
sequence is repeated for an SDLC link station. A retry sequence is
a series of retransmitted frames ( data or control) for which no
positive acknowledgement is received. The current interval between
retry sequences is reflected by the object: wfSdlcLSOperRETRIESn.
The current retries per sequence is reflected by the
object: wfSdlcLSOperRETRIESm."
::= { wfSdlcLSOperEntry 12 }
wfSdlcLSOperRNRLIMIT OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current length of time, in minutes,
that an SDLC link station will allow its adjacent link station to
remain in a busy (RNR) state before declaring it inoperative."
::= { wfSdlcLSOperEntry 13 }
wfSdlcLSOperDATMODE OBJECT-TYPE
SYNTAX INTEGER {
half(1),
full(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects whether the current communications mode with
the adjacent link station is two-way-alternate (half) or
two-way-simultaneous (full)."
DEFVAL { half }
::= { wfSdlcLSOperEntry 14 }
wfSdlcLSOperCreateTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the time, in 1/100ths of seconds,
of the creation of this SDLC link station."
::= { wfSdlcLSOperEntry 15 }
wfSdlcLSOperLastFailCause OBJECT-TYPE
SYNTAX INTEGER {
undefined(1),
rxfrmr(2),
txfrmr(3),
noresp(4),
protoerr(5),
noactiv(6),
rnrlimit(7),
retriesexp(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This enumerated object reflects the cause of the last failure
of this SDLC link station. If the link station has not failed, then
this value has no meaning."
::= { wfSdlcLSOperEntry 16 }
wfSdlcLSOperLastFailCtrlIn2 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the last control octet or octets
(depending on modulus) received by this SDLC link station at the
time of the last failure. If the link station has not failed, then
this value has no meaning."
::= { wfSdlcLSOperEntry 17 }
wfSdlcLSOperLastFailCtrlOut2 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the last control octet or octets
(depending on modulus) sent by this SDLC link station at the time of
the last failure. If the link station has not failed, then this
value has no meaning."
::= { wfSdlcLSOperEntry 18 }
wfSdlcLSOperLastFailFRMRInfo5 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the information field of the FRMR frame
if the last failure for this SDLC link station was as a result of an
invalid frame. Otherwise, this field has no meaning."
::= { wfSdlcLSOperEntry 19 }
wfSdlcLSOperLastFailREPLYTOs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the number of times that the REPLYTO timer
had expired for an SDLC link station at the time of the last failure.
If the link station has not failed, then this value has no meaning."
::= { wfSdlcLSOperEntry 20 }
wfSdlcLSOperGroupAddress OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the group poll address of the secondary link station for
this SDLC link. If this link station is not part of a group, this address
will be NULL."
::= { wfSdlcLSOperEntry 21 }
wfSdlcLSStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF WfSdlcLSStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry in this table contains statistics for a specific
SDLC link station."
::= { wfSdlcGroup 7 }
wfSdlcLSStatsEntry OBJECT-TYPE
SYNTAX WfSdlcLSStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of statistics for a specific SDLC link station"
INDEX { wfSdlcLSStatsIfIndex,
wfSdlcLSStatsAddress }
::= { wfSdlcLSStatsTable 1 }
WfSdlcLSStatsEntry ::= SEQUENCE {
wfSdlcLSStatsIfIndex
INTEGER,
wfSdlcLSStatsAddress
INTEGER,
wfSdlcLSStatsBLUsIns
Counter,
wfSdlcLSStatsBLUsOuts
Counter,
wfSdlcLSStatsOctetsIns
Counter,
wfSdlcLSStatsOctetsOuts
Counter,
wfSdlcLSStatsPollsOuts
Counter,
wfSdlcLSStatsPollRspOuts
Counter,
wfSdlcLSStatsLocalBusies
Counter,
wfSdlcLSStatsRemoteBusies
Counter,
wfSdlcLSStatsIFramesIns
Counter,
wfSdlcLSStatsIFramesOuts
Counter,
wfSdlcLSStatsRetransmits
Counter,
wfSdlcLSStatsIOctetsIns
Counter,
wfSdlcLSStatsIOctetsOuts
Counter,
wfSdlcLSStatsUIFramesIns
Counter,
wfSdlcLSStatsUIFramesOuts
Counter,
wfSdlcLSStatsXIDsIns
Counter,
wfSdlcLSStatsXIDsOuts
Counter,
wfSdlcLSStatsTESTsIns
Counter,
wfSdlcLSStatsTESTsOuts
Counter,
wfSdlcLSStatsREJsIns
Counter,
wfSdlcLSStatsREJsOuts
Counter,
wfSdlcLSStatsFRMRsIns
Counter,
wfSdlcLSStatsFRMRsOuts
Counter,
wfSdlcLSStatsSimsIn
Counter,
wfSdlcLSStatsSimsOut
Counter,
wfSdlcLSStatsRimsIn
Counter,
wfSdlcLSStatsRimsOut
Counter
}
wfSdlcLSStatsIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A list of statistics for an SDLC link station."
::= { wfSdlcLSStatsEntry 1 }
wfSdlcLSStatsAddress OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the poll address of the secondary link station in
this SDLC link. It uniquely identifies the SDLC link station within
a single SDLC port."
::= { wfSdlcLSStatsEntry 2 }
wfSdlcLSStatsBLUsIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total basic link units (BLUs; frames)
received from an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 3 }
wfSdlcLSStatsBLUsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total basic link units (BLUs; frames),
transmitted to an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 4 }
wfSdlcLSStatsOctetsIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total octets received from an adjacent
SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 5 }
wfSdlcLSStatsOctetsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total octets transmitted to an adjacent
SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 6 }
wfSdlcLSStatsPollsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total polls sent to an adjacent SDLC
link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 7 }
wfSdlcLSStatsPollRspOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total polls responded to by the local
SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 8 }
wfSdlcLSStatsLocalBusies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total number of times that the local
SDLC link station has entered a busy state (RNR) since last reset or system
startup."
::= { wfSdlcLSStatsEntry 9 }
wfSdlcLSStatsRemoteBusies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total number of times that an
adjacent ( remote) SDLC link station has entered a busy state
(RNR) since last reset or system startup."
::= { wfSdlcLSStatsEntry 10 }
wfSdlcLSStatsIFramesIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total I-frames received from
an adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 11 }
wfSdlcLSStatsIFramesOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total I-frames transmitted to an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 12 }
wfSdlcLSStatsRetransmits OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total frames retransmitted to an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 13 }
wfSdlcLSStatsIOctetsIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total octets contained in I-frames
received from an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 14 }
wfSdlcLSStatsIOctetsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total octets contained in I-frames
transmitted to an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 15 }
wfSdlcLSStatsUIFramesIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total UI-frames received from an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 16 }
wfSdlcLSStatsUIFramesOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total UI-frames transmitted to an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 17 }
wfSdlcLSStatsXIDsIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total XID frames received from an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 18 }
wfSdlcLSStatsXIDsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total XID frames transmitted to an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 19 }
wfSdlcLSStatsTESTsIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total TEST frames, commands or responses,
received from an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 20 }
wfSdlcLSStatsTESTsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total TEST frames, commands or responses,
transmitted to an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 21 }
wfSdlcLSStatsREJsIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total REJ frames received from an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 22 }
wfSdlcLSStatsREJsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total REJ frames transmitted to an
adjacent SDLC link station since last reset or system startup."
::= { wfSdlcLSStatsEntry 23 }
wfSdlcLSStatsFRMRsIns OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total frame reject (FRMR) frames
received from an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 24 }
wfSdlcLSStatsFRMRsOuts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total frame reject (FRMR) frames
transmitted to an adjacent SDLC link station since last reset
or system startup."
::= { wfSdlcLSStatsEntry 25 }
wfSdlcLSStatsSimsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total set initialization mode (SIM) frames
received from an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 26 }
wfSdlcLSStatsSimsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total set initialization mode (SIM) frames
transmitted to an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 27 }
wfSdlcLSStatsRimsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total request initialization mode (RIM) frames
received from an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 28 }
wfSdlcLSStatsRimsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the total request initialization mode (RIM) frames
transmitted to an adjacent SDLC link station since last reset or
system startup."
::= { wfSdlcLSStatsEntry 29 }
END