| Scalar Object |
| wfDs3E3ConfigEntry | .1.3.6.1.4.1.18.3.4.26.10.1 |
per circuit DS3/E3 configuration objects;
wfDs3E3ConfigLineIndex corresponds to Wellfleet circuit number |
| wfDs3E3ActionEntry | .1.3.6.1.4.1.18.3.4.26.17.1 |
An entry in the DS3E3 Config table |
| Tabular Object |
| wfDs3E3ConfigLineIndex | .1.3.6.1.4.1.18.3.4.26.10.1.5 |
this corresponds to the Wellfleet circuit number |
| wfDs3E3ConfigDelete | .1.3.6.1.4.1.18.3.4.26.10.1.1 |
Create/Delete parameter |
| wfDs3E3ConfigDisable | .1.3.6.1.4.1.18.3.4.26.10.1.2 |
Enable/Disable parameter |
| wfDs3E3ConfigState | .1.3.6.1.4.1.18.3.4.26.10.1.3 |
State of the DS3 Port. |
| wfDs3E3ConfigLastChange | .1.3.6.1.4.1.18.3.4.26.10.1.4 |
The value of sysUpTime at the time the interface entered
its current operational state. |
| wfDs3E3ConfigIfIndex | .1.3.6.1.4.1.18.3.4.26.10.1.6 |
this is value of ifIndex from the Interfaces table of
MIB II (RFC 1213). |
| wfDs3E3ConfigLineType | .1.3.6.1.4.1.18.3.4.26.10.1.7 |
the variety of DS3/E3 application implementing this circuit |
| wfDs3E3ConfigLineCoding | .1.3.6.1.4.1.18.3.4.26.10.1.8 |
the variety of Zero Code Suppression used on the link |
| wfDs3E3ConfigLoopbackConfig | .1.3.6.1.4.1.18.3.4.26.10.1.9 |
the loopback configuration of the DS3/E3 interface |
| wfDs3E3ConfigLineStatus | .1.3.6.1.4.1.18.3.4.26.10.1.10 |
the status of the DS3/E3 line |
| wfDs3E3ConfigPrimaryClockSource | .1.3.6.1.4.1.18.3.4.26.10.1.11 |
Selects the Primary source of the Tx Clock for the DS3/E3
interface |
| wfDs3E3ConfigSecondaryClockSource | .1.3.6.1.4.1.18.3.4.26.10.1.12 |
Selects the Secondary source of the Tx Clock for the DS3/E3
interface |
| wfDs3E3ConfigMtu | .1.3.6.1.4.1.18.3.4.26.10.1.13 |
MTU parameter for all channels on DS3 . |
| wfDs3E3ConfigLineBuildOut | .1.3.6.1.4.1.18.3.4.26.10.1.14 |
Set according to cable length, short (less than 225 feet)
or long (greater than 225 feet). |
| wfDs3E3ConfigCurrentClock | .1.3.6.1.4.1.18.3.4.26.10.1.15 |
Indicates the clock source currently in use by the DS1 |
| wfDs3E3ConfigExtClockOperational | .1.3.6.1.4.1.18.3.4.26.10.1.16 |
Indicates whether the External clock is operational |
| wfDs3E3ConfigSetupAlarmThreshold | .1.3.6.1.4.1.18.3.4.26.10.1.17 |
Specifies setup time for performance failure conditions,
in seconds. When a performance defect is present for greater
than the time specified by this parameter a performance
failure is registered and a message is logged. |
| wfDs3E3ConfigClearAlarmThreshold | .1.3.6.1.4.1.18.3.4.26.10.1.18 |
Specifies clear time for performance failure conditions,
in seconds. When a performance failure condition has been
cleared for greater than the time specified by this parameter
then the failure cleared condition is registered and a
message is logged. |
| wfDs3E3ConfigLoopbackState | .1.3.6.1.4.1.18.3.4.26.10.1.19 |
Indicates the current loopback state of this interface.
The interface can be in one the following states:
Line Loopback
Payload Loopback
no loopback
Loopback modes can be initiated by either of two methods:
Manager requested Loopback is initiated by the Manager of
this device.
Network requested Loopback is initiated by this interface
receiving an in-band request on the network from the far
end device. |
| wfDs3E3ConfigSendCode | .1.3.6.1.4.1.18.3.4.26.10.1.20 |
This variable is currently read-only and it indicates what type of code has
been sent across the DS3 interface by the device. The values mean:
SENDNOCODE - sending looped or normal data
SENDLINECODE - sending a request for a line loopback
SENDPAYLOADCODE - sending a request for a payload loopback
SENDDS1LOOPCODE - sending a request for a DS1 loopback
|
| wfDs3E3ActionPortLineNumber | .1.3.6.1.4.1.18.3.4.26.17.1.1 |
Instance ID LineNumber, filled in by driver |
| wfDs3E3ActionSendFeacLoopCode | .1.3.6.1.4.1.18.3.4.26.17.1.2 |
Selects a Far End Alarm and Control Channel code to be
sent to the remote end. |
| wfDs3E3ActionSendFeacDs1LoopUpCode | .1.3.6.1.4.1.18.3.4.26.17.1.3 |
Selects Loop Up code to be sent to the remote end for a DS1.
Value passed through this attribute is the DS1 Port number
(1 through 28). |
| wfDs3E3ActionSendFeacDs1LoopDownCode | .1.3.6.1.4.1.18.3.4.26.17.1.4 |
Selects Loop Down code to be sent to the remote end for a DS1.
Value passed through this attribute is the DS1 Port number
(1 through 28). |
| wfDs3E3ActionClearCurrentStats | .1.3.6.1.4.1.18.3.4.26.17.1.5 |
Clears this port's Current 15 minute Statistics. |
| wfDs3E3ActionClearFarEndCurrentStats | .1.3.6.1.4.1.18.3.4.26.17.1.6 |
Clears this port's Far End, Current 15 minute Statistics. |
| wfDs3E3ActionClearDayCurrentStats | .1.3.6.1.4.1.18.3.4.26.17.1.7 |
Clears this port's Current Day Statistics. |
| wfDs3E3ActionClearFarEndDayCurrentStats | .1.3.6.1.4.1.18.3.4.26.17.1.8 |
Clears this port's Far End, Current Day Statistics. |
| wfDs3E3ActionClearIntervalStats | .1.3.6.1.4.1.18.3.4.26.17.1.9 |
Clears All Interval Statistics (15 minute and day) of this port. |
| wfDs3E3ActionClearFarEndIntervalStats | .1.3.6.1.4.1.18.3.4.26.17.1.10 |
Clears All Far End Interval Statistics (15 minute and day) of this port. |
| Table |
| wfDs3E3ConfigTable | .1.3.6.1.4.1.18.3.4.26.10 |
The DS3/E3 Configuration table |
| wfDs3E3ActionTable | .1.3.6.1.4.1.18.3.4.26.17 |
DS3E3 configuration Action record -
write only Configuration parameters |