CISCO-CALLHOME-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
NOTIFICATION-TYPE,
Unsigned32,
Counter32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
TEXTUAL-CONVENTION, TruthValue,
RowStatus,TimeStamp FROM SNMPv2-TC
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
InetAddressType, InetAddress
FROM INET-ADDRESS-MIB
SyslogSeverity FROM CISCO-SYSLOG-MIB
ciscoMgmt FROM CISCO-SMI;
ciscoCallHomeMIB MODULE-IDENTITY
LAST-UPDATED "200408020000Z"
ORGANIZATION "Cisco Systems Inc. "
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553 -NETS
E-mail: cs-san@cisco.com, cs-lan-switch-snmp@cisco.com"
DESCRIPTION
"The MIB module for the management of Call Home feature
within the frame work of Cisco's Call Home
architecture.
Customers deploying solutions to run mission critical
applications such as storage solutions demand very high
availability and Serviceability from their products
and/or support partners.
To meet these requirements, a feature called
'CallHome' is provided which allows the system
experiencing Hardware/Software problems to
automatically send the relevant failure information
back to the Support Center at the Support Partners for
troubleshooting or to get replacement hardware
dispatched. This feature also provides advanced
features that allow storage systems to send
performance, accounting and system health information
in addition to just the fault information."
REVISION "200408020000Z"
DESCRIPTION
"Added new compliance section 'chMIBCompliance3'."
REVISION "200402110000Z"
DESCRIPTION
"New Table 'callHomeSwInventoryTable' has been added
to provide the callhome inventory information about
the software services.
New objects 'ccmPeriodicSwInventoryMsgEnable',
'ccmPeriodicSwInventoryTimeFrame' and
'ccmMsgThrottlingEnable' has been added."
REVISION "200402090000Z"
DESCRIPTION
"Max size of 'callHomeDestProfileName' has been
changed to 31 chars."
REVISION "200310300000Z"
DESCRIPTION
"New object 'callHomeDestProfileAlertGroups' has been
added to the callHomeDestProfileTable.
Row creation support has been added in the
callHomeDestProfileTable.
New Table 'callHomeAlertGroupTypeTable' has been added."
REVISION "200305200000Z"
DESCRIPTION
"New object 'callHomeDestProfileMsgLevel' has been
added to the callHomeDestProfileTable."
REVISION "200210280000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 300 }
ccmCallHomeNotifications OBJECT IDENTIFIER
::= { ciscoCallHomeMIB 0 }
ciscoCallHomeMIBObjects OBJECT IDENTIFIER ::= { ciscoCallHomeMIB 1 }
chMIBConformance OBJECT IDENTIFIER ::= { ciscoCallHomeMIB 2 }
ccmCallHomeConfiguration OBJECT IDENTIFIER
::= { ciscoCallHomeMIBObjects 1 }
ccmCallHomeStats OBJECT IDENTIFIER ::= { ciscoCallHomeMIBObjects 2 }
CallHomeAlert ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The type of the CallHome alert.
noOp (1) - no alert
test (2) - alert name 'Test'
inventory (3) - alert name 'Inventory'
."
SYNTAX INTEGER {
noOp (1),
test (2),
inventory (3)
}
CallHomeMsgFormat ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"CallHome Message format.
xml (1) - XML (Extensible Markup Language)
- encoded.
fullText (2) - Plain text without any encoding.
shortText (3) - Short text without any encoding
The context of the CallHome message depends on the
message. In general, all the CallHome message is sent
with following information :
'Subject : System Notification from <device-name>'
'TimeStamp :'
'Message Name :'
'Message Type :'
'Level :'
'Message Device ID :'
'Customer ID :' (optional)
'Contract ID :' (optional)
'Site ID :' (optional)
'Server ID :'
'Message Description :'
'Device Name :'
'Contact Name :'
'Contact email :'
'Contact Phone :' (optional)
'Street Address :' (optional)
'Model Name :'
'Serial Number :'
'Part Number :'
'Chassis Hardware Version :'
'Supervisor Software Version :'
Following information are required only if a hardware
event caused the CallHome message :
'Affected FRU'
'Affected FRU Serial Number'
'Affected FRU Slot :'
'Affected FRU Hardware Version :'
'Affected FRU Software Version :'
Following is required for all the messages :
'Command Output :'
The command output may depend on the implementation and
severity of the CallHome message. But at minimum,
following information which are contained in the output
of the CLI commands must be included.
- Hardware model
- software version
- context information explaining the state of the device.
- uptime
- brief inventory information
The exact format depends on the format type chosen.
For 'xml', the above information is encoded in the XML
format. For 'fullText', above information is sent out in
plain text. For 'shortText', only following information
is provided in plain text:
'Subject : System Notification from <device-name> '
'Device Id : '
'TimeStamp : '
'Error Message : '
'Severity Level :'
."
REFERENCE
"For more information on the XML, refer to RFC3023."
SYNTAX INTEGER {
xml (1),
fullText (2),
shortText (3)
}
CallHomeTransportMethod ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"CallHome transport mechanism used to deliver the alert
messages.
email (1) - via email
ftp (2), - via ftp
http (3) - via http
."
SYNTAX INTEGER {
email (1),
ftp (2),
http (3)
}
CallHomeMsgLevel ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This object contains the severity level for use as a
threshold for filtering the alerts sent to a destination
profile.
It ranges from 1 to 10, with 10 being highest severity."
SYNTAX INTEGER {
debug (1),
normal (2),
notification (3),
warning (4),
minor (5),
major (6),
critical (7),
fatal (8),
disaster (9),
catastrophic (10)
}
AlertGroupList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"AlertGroups are a pre-defined set of call-home alerts.
Users can specify these alert groups for a destination
profile, to choose the call-home alerts messages to be
sent out to the destination. This object represents
the list of alert groups (alert group types)
configured for a destination profile.
Each 'bit' within the value of an object of this type,
specifies a configured alertgroup type.
Bit position '0' ( most significant bit) in the value
of this object is reserved.
The value of each 'bit' (set/reset) represents whether
an alert group type is configured or not for a
particular destination profile.
Bit position 1, represents whether the
'callHomeAlertGroupName' corresponding to the
'callHomeAlertGroupTypeIndex' 1 in the
'callHomeAlertGroupTypeTable' is configured or
not for a particular destination profile.
Bit position 2, represents whether the
'callHomeAlertGroupName' corresponding to the
'callHomeAlertGroupTypeIndex' 2 in the
'callHomeAlertGroupTypeTable' is configured or
not for a particular destination profile.
If there is no entry in the 'alertGroupTypeTable',
with 'alertGroupTypeIndex' 'n', then
bit position 'n' in the value of this object is
irrelevant.
If the length of an object of this type is less
than 8 bytes, then the alert group types which are
not represented are not considered to be part of this
list, i.e., effectively, the string is extended to
be of length 8 bytes by appending bytes
containing x'00'. Note that this means that the
zero length string represents the 'list is empty'
value."
SYNTAX OCTET STRING (SIZE (0..8))
callHomeEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables/disables the CallHome infrastructure
on the local device."
::= { ccmCallHomeConfiguration 1 }
sysContactPhoneNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0|12|13..17))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The phone number of the contact person for this managed
node. The phone number must start with '+' and contains
only numeric characters except for space and '-'.
Some valid phone numbers are
+44 20 8332 9091
+45 44886556
+81-46-215-4678
+1-650-327-2600
A set operation on this object with a invalid format will
result in an error."
::= { ccmCallHomeConfiguration 2 }
sysContactEmailAddress OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The email address of the contact person for this managed
node. The format of this object is an an e-mail address
which conforms to RFC822 and RFC1123 'addr-spec'
syntax.
Some valid Email Addresses are
raj@helpme.com,
bob@service.com,
mtom@abc.caview.ca.us
A set operation on this object with a invalid format will
result in an error."
::= { ccmCallHomeConfiguration 3 }
sysStreetAddress OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The mailing address of this managed node."
::= { ccmCallHomeConfiguration 4 }
callHomeCustomerId OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A string, in whatever format is appropriate, to identify
the customer."
::= { ccmCallHomeConfiguration 5 }
callHomeContractId OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A string, in whatever format is appropriate, to identify
the support contract between the customer and support
partner."
::= { ccmCallHomeConfiguration 6 }
callHomeSiteId OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A location identifier of this device."
::= { ccmCallHomeConfiguration 7 }
callHomeDeviceServicePriority OBJECT-TYPE
SYNTAX SyslogSeverity
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The service priority of the device.
This determines how fast the device has to be serviced."
DEFVAL { debug }
::= { ccmCallHomeConfiguration 8 }
callHomeAlertAction OBJECT-TYPE
SYNTAX CallHomeAlert
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object acts as a trigger by which the generation of
a particular type of alert can be verified. Specifically,
setting this object to a type of alert triggers the
sending of a callhome message for the specified type
so that the call home backend is activated.
No action is taken if this object is set to 'noOp'.
The value of the object when read is always 'noOp'."
::= { ccmCallHomeConfiguration 9 }
callHomeAlertActionStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
successful (2),
inprogress (3),
failed (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object provides the status of the last callhome action
invocation.
unknown (1) - unknown
successful (2) - successful
inprogress (3) - action in progress
failed (4) - failed
If the value of this object is 'failed', then the
callHomeAlertActionFailureCause provides the cause for the
failure.
Management stations could read value of this object after a
successful set to the callHomeAlertAction object to find
out the result of the test."
::= { ccmCallHomeConfiguration 10 }
callHomeAlertActionFailureCause OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object provides the failure cause for the last
callhome test invocation.
Note that this object is valid only if value of
callHomeAlertActionStatus is 'failed'."
::= { ccmCallHomeConfiguration 11 }
callHomeDestProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CallHomeDestProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains destination profiles.
The CallHome feature requires the destination profiles to be
setup to be able to send the CallHome messages to
destinations configured.
By default there will be 3 entries in this table with
callHomeDestProfileName 'xml', 'full_txt' and 'short_txt'.
User can't delete these 3 entries, but can modify the
values of callHomeDestProfileMaxMsgSize and
callHomeDestProfileMsgLevel in these entries. However, the
user can create/delete/modify entries with other
callHome profile names."
::= { ccmCallHomeConfiguration 12 }
callHomeDestProfileEntry OBJECT-TYPE
SYNTAX CallHomeDestProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing information about a CallHome
destination."
INDEX {callHomeDestProfileName}
::= { callHomeDestProfileTable 1 }
CallHomeDestProfileEntry ::= SEQUENCE {
callHomeDestProfileName SnmpAdminString,
callHomeDestProfileMsgFormat CallHomeMsgFormat,
callHomeDestProfileMaxMsgSize Unsigned32,
callHomeDestProfileTrnsprtMthd CallHomeTransportMethod,
callHomeDestProfileStatus RowStatus,
callHomeDestProfileMsgLevel CallHomeMsgLevel,
callHomeDestProfileAlertGroups AlertGroupList
}
callHomeDestProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..31))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Name of the destination profile."
::= { callHomeDestProfileEntry 1 }
callHomeDestProfileMsgFormat OBJECT-TYPE
SYNTAX CallHomeMsgFormat
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The CallHome format used with profile while sending
the message."
DEFVAL { xml }
::= { callHomeDestProfileEntry 2 }
callHomeDestProfileMaxMsgSize OBJECT-TYPE
SYNTAX Unsigned32 (0..1000000)
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum message size that can be sent to destination
pointed to by this destination profile.
If the 'callHomeDestProfileMsgFormat' is set to
'xml' or 'full_txt' then the default value for this
object is '500,000'.
If the ''callHomeDestProfileMsgFormat' is 'short_txt'
then the default value for this object is '4000'.
A value of 0 for this object indicates no limitation
on maximum message size that can be sent to destination
pointed to by this destination profile."
::= { callHomeDestProfileEntry 3 }
callHomeDestProfileTrnsprtMthd OBJECT-TYPE
SYNTAX CallHomeTransportMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"CallHome transport method used to deliver the alert
messages."
DEFVAL {email}
::= { callHomeDestProfileEntry 4 }
callHomeDestProfileStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Status of this row."
::= { callHomeDestProfileEntry 5 }
callHomeDestProfileMsgLevel OBJECT-TYPE
SYNTAX CallHomeMsgLevel
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object contains the threshold level, used for
filtering alert messages sent to a destination.
Callhome alert message with severity level lower than
the configured threshold level would not be sent.
The default threshold level is debug (1), which means
all the alert messages will be sent."
DEFVAL {debug}
::= { callHomeDestProfileEntry 6 }
callHomeDestProfileAlertGroups OBJECT-TYPE
SYNTAX AlertGroupList
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object represent the list of configured alert
groups for this destination profile.
User can modify the configured alert groups, by
Setting/Resetting the appropriate bits in this
object. Resetting all the bits to '0' means no alert
group is configured, hence no alert would be sent
to the destination profile.
If the existing value of this object has all bits
'set' , corresponding to all the
'callhomeAlertGroupTypeIndex' in the
'callHomeAlertGroupTypeTable', then the user can
either 'reset all' or 'set all' of the above
configured bits. User can't choose to modify only
few bits in this case.
However if the existing value of this object,
has not have 'all bits set' corresponding
to the all 'callHomeAlertGroupTypeIndex' in the
'callHomeAlertGroupTypeTable', then user can
choose to modify only few or all the bits."
::= { callHomeDestProfileEntry 7 }
callHomeEmailAddrTblMaxEntries OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of entries that the agent supports in
the callHomeDestEmailAddressTable."
::= { ccmCallHomeConfiguration 13 }
callHomeDestEmailAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF CallHomeDestEmailAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains email addresses for the destination
profiles. Each destination profile could contain one or more
email addresses associated with it."
::= { ccmCallHomeConfiguration 14 }
callHomeDestEmailAddressEntry OBJECT-TYPE
SYNTAX CallHomeDestEmailAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing information about a CallHome
destination email address.
An entry cannot made 'active' until corresponding instance
of 'callHomeDestEmailAddress' is created.
Also, 'callHomeDestEmailAddress' cannot be modified when
'callHomeDestEmailAddressStatus' is 'active'.
To modify 'callHomeDestEmailAddress', the entry must be
deleted and re-created with the new value of it."
INDEX {callHomeDestProfileName,
callHomeDestEmailAddressIndex}
::= { callHomeDestEmailAddressTable 1 }
CallHomeDestEmailAddressEntry ::= SEQUENCE {
callHomeDestEmailAddressIndex Unsigned32,
callHomeDestEmailAddress SnmpAdminString,
callHomeDestEmailAddressStatus RowStatus
}
callHomeDestEmailAddressIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer value, greater than zero, and less
than and equal to callHomeEmailAddrTblMaxEntries, which
identifies an Email address.
These integer values should be non-volatile."
::= { callHomeDestEmailAddressEntry 1 }
callHomeDestEmailAddress OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The email address associated this destination profile. The
format of this object is an an e-mail address which conforms
to RFC822 and RFC1123 'addr-spec' syntax. Some examples are
raj@helpme.com,
bob@service.com,
mtom@abc.caview.ca.us.
A set operation on this object with a invalid format will
result in an error."
::= { callHomeDestEmailAddressEntry 2 }
callHomeDestEmailAddressStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Status of this row."
::= { callHomeDestEmailAddressEntry 3 }
callHomeEmailFrom OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The email address that is to be used in the 'From' field
when sending the email using SMTP. The format of this object
is an e-mail address which conforms to RFC822 and RFC1123
'addr-spec' syntax.
Some examples are
raj@helpme.com,
bob@service.com,
mtom@abc.caview.ca.us.
A set operation on this object with a invalid format will
result in an error."
REFERENCE
"RFC 2821 - Simple Mail Transfer Protocol and
RFC822 - Standard for the Format of Arpa Internet Text
Messages."
::= { ccmCallHomeConfiguration 15 }
callHomeEmailReplyTo OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The email address that is to be used in the 'Reply-To'
field when sending the email using SMTP. The format of
this object is an e-mail address which conforms to RFC822
and RFC1123 'addr-spec' syntax.
Some examples are
raj@helpme.com,
bob@service.com,
mtom@abc.caview.ca.us.
A set operation on this object with a invalid format will
result in an error."
REFERENCE
"RFC 2821 - Simple Mail Transfer Protocol and
RFC822 - Standard for the Format of Arpa Internet Text
Messages."
::= { ccmCallHomeConfiguration 16 }
callHomeEmailMsgDispNotification OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The email address to which the Message Disposition
Notification (also called 'Return Receipt') sent when the
email sent from this device is read by the receiver. The
format of this object is an an e-mail address which conforms
to RFC822 and RFC1123 'addr-spec' syntax.
Some examples are
raj@helpme.com,
bob@service.com,
mtom@abc.caview.ca.us.
A set operation on this object with a invalid format will
result in an error."
REFERENCE
"RFC 2298 - An Extensible Message Format
for Message Disposition Notifications."
::= { ccmCallHomeConfiguration 17 }
callHomeSmtpServerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Address Type of the SMTP server."
::= { ccmCallHomeConfiguration 18 }
callHomeSmtpServerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Address of the SMTP server."
REFERENCE
"RFC 2821 - Simple Mail Transfer Protocol."
::= { ccmCallHomeConfiguration 19 }
callHomeSmtpServerPort OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Port of the SMTP server."
REFERENCE
"RFC 2821 - Simple Mail Transfer Protocol."
DEFVAL { 25 }
::= { ccmCallHomeConfiguration 20 }
ccmSmtpServersTblMaxEntries OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the maximum number of SMTP servers supported by
this device. A value of zero indicates no limitation on
the number of SMTP servers."
::= { ccmCallHomeConfiguration 21 }
ccmSmtpServersTable OBJECT-TYPE
SYNTAX SEQUENCE OF CcmSmtpServersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries that identify lists of
SMTP servers that may be used by system to send out
e-mail notification to addresses configured in
callHomeDestEmailAddressTable.
The maximum number of entries that can be created for
for this table is limited by the scalar object
ccmSmtpServersTblMaxEntries.
The device sequentially tries all the entries in this
table until it successfully sends out an email notification."
::= { ccmCallHomeConfiguration 22 }
ccmSmtpServersEntry OBJECT-TYPE
SYNTAX CcmSmtpServersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing information about a SMTP server.
An entry cannot made 'active' until corresponding instance
of all objects in the same conceptual row are created.
Any object in the entry can not be modified if the value
of ccmSmtpServersStatus is 'active'."
INDEX { ccmSmtpServersAddrType,
ccmSmtpServersAddr }
::= { ccmSmtpServersTable 1 }
CcmSmtpServersEntry ::= SEQUENCE {
ccmSmtpServersAddrType InetAddressType,
ccmSmtpServersAddr InetAddress,
ccmSmtpServersPort Unsigned32,
ccmSmtpServersStatus RowStatus
}
ccmSmtpServersAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address Type of the SMTP server."
::= { ccmSmtpServersEntry 1 }
ccmSmtpServersAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of the SMTP server."
REFERENCE
"RFC 2821 - Simple Mail Transfer Protocol."
::= { ccmSmtpServersEntry 2 }
ccmSmtpServersPort OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Port of the SMTP server."
REFERENCE
"RFC 2821 - Simple Mail Transfer Protocol."
DEFVAL { 25 }
::= { ccmSmtpServersEntry 3 }
ccmSmtpServersStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status object used to manage the rows in this table."
::= { ccmSmtpServersEntry 4 }
callHomeLastAlertSent OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when the last CallHome alert
was sent."
::= { ccmCallHomeStats 1}
callHomeAlerts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of CallHome alerts sent."
::= { ccmCallHomeStats 2}
ccmSysLogSeverity OBJECT-TYPE
SYNTAX SyslogSeverity
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Different devices implementing this mib may use
different criteria for issuing call home alerts.
For the devices that issue call home alerts based on
severity level of the syslog messages generated on
the device, this object determines syslog severity
levels beyond which a call home alert message will be
issued.
Any syslog message with a severity value greater than
the value set for this object will be ignored by the agent.
Note: severity numeric values increase as their
severity decreases, e.g. error(4) is more severe
than debug(8).
For the devices that do not issue call home alerts based
on syslog severity levels this object has no effect."
::= { ccmCallHomeConfiguration 23 }
ccmEnableSmtpServerNotif OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable indicates whether the system produces
the ccmSmtpServerFailNotif.
A false value for this object will prevent
ccmSmtpServerFailNotif notification being generated
by the device."
::= { ccmCallHomeConfiguration 24 }
callHomeAlertGroupTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF CallHomeAlertGroupTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about all the
alert groups types supported in the system.
Whenever the system opts not to support a
particular alert group type, the corresponding
entry in this table will be removed, and a
'ccmAlertGroupTypeDeletedNotif' will be sent.
Whenever the system opts to support a new
alert group type, a new entry into this table
will be added, and a
'ccmAlertGroupTypeAddedNotif' will be sent."
::= { ccmCallHomeConfiguration 25 }
callHomeAlertGroupTypeEntry OBJECT-TYPE
SYNTAX CallHomeAlertGroupTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing information about a
particular callHome alert group type
in the system."
INDEX {callHomeAlertGroupTypeIndex}
::= { callHomeAlertGroupTypeTable 1 }
CallHomeAlertGroupTypeEntry ::= SEQUENCE {
callHomeAlertGroupTypeIndex Unsigned32,
callHomeAlertGroupName SnmpAdminString
}
callHomeAlertGroupTypeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..256)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represent the index corresponds
to the particular alert group type configured
in the system."
::= { callHomeAlertGroupTypeEntry 1 }
callHomeAlertGroupName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the name of
alert group configured in the system."
::= { callHomeAlertGroupTypeEntry 2 }
callHomeSwInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF CallHomeSwInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains inventory information about all the
software services currently enabled in the system.
When a software service is disabled from the system, all
the entries corresponds to that software service will be
deleted automatically from the table."
::= { ccmCallHomeConfiguration 26 }
callHomeSwInventoryEntry OBJECT-TYPE
SYNTAX CallHomeSwInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing information about the name value
pair for a particular software service enabled in the
system."
INDEX {callHomeSwServiceName, callHomeInventoryNVPairIndex}
::= { callHomeSwInventoryTable 1 }
CallHomeSwInventoryEntry ::= SEQUENCE {
callHomeSwServiceName SnmpAdminString,
callHomeInventoryNVPairIndex Unsigned32,
callHomeInventoryInfoName OCTET STRING,
callHomeInventoryInfoValue OCTET STRING
}
callHomeSwServiceName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the name of software service
enabled in the system."
::= { callHomeSwInventoryEntry 1 }
callHomeInventoryNVPairIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..256)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the index corresponds to the name
value pair for a particular software service enabled in
the system.
The name value pair is a 'tuple' of (inventory info-name,
and inventory info-value) and this object uniquely
identifies a value of the tuple, for a particular
software service enabled in the system."
::= { callHomeSwInventoryEntry 2 }
callHomeInventoryInfoName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the name of a feature , for a
particular software service enabled in the system.
For example, the value of this object could be
'number of VSAN' for the software service 'vsan_manager'."
::= { callHomeSwInventoryEntry 3 }
callHomeInventoryInfoValue OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the value for the feature name
specified in the corresponding instance of
'callHomeInventroyInfoName' object.
For example, the value of this object could be '10' for
the corresponding instance of 'callHomeInventroyInfoName'
object with value 'number of VSAN'."
::= { callHomeSwInventoryEntry 4 }
ccmPeriodicSwInventoryMsgEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables/disables the sending of periodic
software inventory callhome message on the system."
DEFVAL { true }
::= { ccmCallHomeConfiguration 27 }
ccmPeriodicSwInventoryTimeFrame OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
UNITS "days"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object represents the time frame for sending the
periodic software inventory callhome message, if the
periodic software inventory is enabled on the system
ie., the value of 'ccmPeriodicSwInventoryMsgEnable'
object is set to 'true'."
DEFVAL { 7 }
::= { ccmCallHomeConfiguration 28 }
ccmMsgThrottlingEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables/disables the message throttling
mechanism implemented on the system.
The message throttling mechanism limits the number
of callhome messages for a alert type, sent with in
a time frame. The maximum number of callhome alert
messages that can be sent out for a particular alert
type is '30' in a time frame of 2 hours.
That means, if the number of message sent exceeds the
maximum limit (30), with in the given time frame
(2 hours) then any further messages for that alert type
will be discarded within that time frame.
Only 30 messages for each alert type will be sent until
2 hours from the time the first message was sent. In case
2 hours has already elapsed since the first such message
was sent, then time frame and the count for the number of
messages will be reset to '0'."
DEFVAL { true }
::= { ccmCallHomeConfiguration 29 }
ccmSmtpServerFailNotif NOTIFICATION-TYPE
OBJECTS {
ccmSmtpServersPort
}
STATUS current
DESCRIPTION
"A ccmSmtpServerFailNotif is sent if the device fails on
sending an e-mail notification to SMTP server in
ccmSmtpServersTable."
::= { ccmCallHomeNotifications 1 }
ccmAlertGroupTypeAddedNotif NOTIFICATION-TYPE
OBJECTS {
callHomeAlertGroupName
}
STATUS current
DESCRIPTION
"A ccmAlertGroupTypeAddedNotif is sent, when
a new entry corresponds to the
'callHomealertGroupName' object in this
notification is added into the
callHomeAlertGroupTypeTable."
::= { ccmCallHomeNotifications 2 }
ccmAlertGroupTypeDeletedNotif NOTIFICATION-TYPE
OBJECTS {
callHomeAlertGroupName
}
STATUS current
DESCRIPTION
"A ccmAlertGroupTypeAddedNotif is sent, when an
entry corresponds to 'callHomeAlertGroupName'
object in this notification is deleted
from the callHomeAlertGroupTypeTable."
::= { ccmCallHomeNotifications 3 }
chMIBCompliances
OBJECT IDENTIFIER ::= { chMIBConformance 1 }
chMIBGroups
OBJECT IDENTIFIER ::= { chMIBConformance 2 }
chMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CallHome feature.
OBJECT ccmSmtpServersAddrType
SYNTAX INTEGER { ipv4(1) }
DESCRIPTION
An implementation is only required to
support IPv4 addresses.
OBJECT callHomeDestProfileName
SYNTAX SnmpAdminString (SIZE (1..11))
DESCRIPTION
An implementation is only required to
support a profile name of size 1 to 11
octets."
MODULE MANDATORY-GROUPS { chConfigurationGroup,
chStatisticsGroup }
GROUP chSystemInformationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chEmailMsgDispGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chSingleSmtpServerGroup
DESCRIPTION
"This group is mandatory for devices which support
single SMTP server."
GROUP chMultipleSmtpServersGroup
DESCRIPTION
"This group is mandatory for devices which support
multiple SMTP servers."
GROUP ccmSysLogSeverityGroup
DESCRIPTION
"This group is mandatory for devices that issue
call home alerts based on severity level of the
syslog messages generated on the device."
GROUP ccmMIBNotificationsConfigGroup
DESCRIPTION
"The ccmMIBNotificationsConfigGroup is optional."
GROUP ccmMIBNotificationsGroup
DESCRIPTION
"The ccmMIBNotificationsGroup is optional."
OBJECT callHomeDestProfileTrnsprtMthd
SYNTAX INTEGER {
email (1)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'email' needs to be supported."
OBJECT callHomeDestProfileMsgFormat
SYNTAX INTEGER {
shortText (3)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'shortText' needs to be supported."
OBJECT callHomeDestProfileStatus
SYNTAX INTEGER {
active (1)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'active' needs to be supported."
OBJECT callHomeDestEmailAddress
SYNTAX SnmpAdminString (SIZE(1..63))
DESCRIPTION
"An implementation is only required to
support an address of size 1 to 63
octets."
OBJECT callHomeDestEmailAddressStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT ccmSmtpServersPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT ccmSmtpServersStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT callHomeEmailFrom
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octets."
OBJECT callHomeEmailReplyTo
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
OBJECT callHomeEmailMsgDispNotification
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
::= { chMIBCompliances 1 }
chMIBCompliance1 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CallHome feature.
OBJECT ccmSmtpServersAddrType
SYNTAX INTEGER { ipv4(1) }
DESCRIPTION
An implementation is only required to
support IPv4 addresses.
OBJECT callHomeDestProfileName
SYNTAX SnmpAdminString (SIZE (1..31))
DESCRIPTION
An implementation is only required to
support a profile name of size 1 to 31
octets."
MODULE MANDATORY-GROUPS { chConfigurationGroup1,
chStatisticsGroup }
GROUP chSystemInformationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chEmailMsgDispGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chSingleSmtpServerGroup
DESCRIPTION
"This group is mandatory for devices which support
single SMTP server."
GROUP chMultipleSmtpServersGroup
DESCRIPTION
"This group is mandatory for devices which support
multiple SMTP servers."
GROUP ccmSysLogSeverityGroup
DESCRIPTION
"This group is mandatory for devices that issue
call home alerts based on severity level of the
syslog messages generated on the device."
GROUP ccmMIBNotificationsConfigGroup
DESCRIPTION
"The ccmMIBNotificationsConfigGroup is optional."
GROUP ccmMIBNotificationsGroup1
DESCRIPTION
"The ccmMIBNotificationsGroup is optional."
OBJECT callHomeDestProfileTrnsprtMthd
SYNTAX INTEGER {
email (1)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'email' needs to be supported."
OBJECT callHomeDestProfileMsgFormat
SYNTAX INTEGER {
shortText (3)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'shortText' needs to be supported."
OBJECT callHomeDestProfileStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'active' needs to be supported."
OBJECT callHomeDestEmailAddress
SYNTAX SnmpAdminString (SIZE(1..63))
DESCRIPTION
"An implementation is only required to
support an address of size 1 to 63
octets."
OBJECT callHomeDestEmailAddressStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT ccmSmtpServersPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT ccmSmtpServersStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT callHomeEmailFrom
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
OBJECT callHomeEmailReplyTo
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
OBJECT callHomeEmailMsgDispNotification
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
::= { chMIBCompliances 2 }
chMIBCompliance2 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CallHome feature.
OBJECT ccmSmtpServersAddrType
SYNTAX INTEGER { ipv4(1) }
DESCRIPTION
An implementation is only required to
support IPv4 addresses.
OBJECT callHomeDestProfileName
SYNTAX SnmpAdminString (SIZE (1..31))
DESCRIPTION
An implementation is only required to
support a profile name of size 1 to 31
octets."
MODULE MANDATORY-GROUPS { chConfigurationGroup2,
chStatisticsGroup ,
chSwInventoryInfoGroup }
GROUP chSystemInformationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chEmailMsgDispGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chSingleSmtpServerGroup
DESCRIPTION
"This group is mandatory for devices which support
single SMTP server."
GROUP chMultipleSmtpServersGroup
DESCRIPTION
"This group is mandatory for devices which support
multiple SMTP servers."
GROUP ccmSysLogSeverityGroup
DESCRIPTION
"This group is mandatory for devices that issue
call home alerts based on severity level of the
syslog messages generated on the device."
GROUP ccmMIBNotificationsConfigGroup
DESCRIPTION
"The ccmMIBNotificationsConfigGroup is optional."
GROUP ccmMIBNotificationsGroup1
DESCRIPTION
"The ccmMIBNotificationsGroup is optional."
OBJECT callHomeDestProfileTrnsprtMthd
SYNTAX INTEGER {
email (1)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'email' needs to be supported."
OBJECT callHomeDestProfileMsgFormat
SYNTAX INTEGER {
shortText (3)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'shortText' needs to be supported."
OBJECT callHomeDestProfileStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'active' needs to be supported."
OBJECT callHomeDestEmailAddress
SYNTAX SnmpAdminString (SIZE(1..63))
DESCRIPTION
"An implementation is only required to
support an address of size 1 to 63
octets."
OBJECT callHomeDestEmailAddressStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT ccmSmtpServersPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT ccmSmtpServersStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT callHomeEmailFrom
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
OBJECT callHomeEmailReplyTo
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
OBJECT callHomeEmailMsgDispNotification
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
::= { chMIBCompliances 3 }
chMIBCompliance3 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which
implement the CallHome feature.
OBJECT ccmSmtpServersAddrType
SYNTAX INTEGER { ipv4(1) }
DESCRIPTION
An implementation is only required to
support IPv4 addresses.
OBJECT callHomeDestProfileName
SYNTAX SnmpAdminString (SIZE (1..31))
DESCRIPTION
An implementation is only required to
support a profile name of size 1 to 31
octets."
MODULE MANDATORY-GROUPS { chConfigurationGroup2,
chStatisticsGroup
}
GROUP chSystemInformationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chEmailMsgDispGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chSwInventoryInfoGroup1
DESCRIPTION
"Implementation of this group is optional."
GROUP chPeriodicSwInventoryInfoGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP chSingleSmtpServerGroup
DESCRIPTION
"This group is mandatory for devices which support
single SMTP server."
GROUP chMultipleSmtpServersGroup
DESCRIPTION
"This group is mandatory for devices which support
multiple SMTP servers."
GROUP ccmSysLogSeverityGroup
DESCRIPTION
"This group is mandatory for devices that issue
call home alerts based on severity level of the
syslog messages generated on the device."
GROUP ccmMIBNotificationsConfigGroup
DESCRIPTION
"The ccmMIBNotificationsConfigGroup is optional."
GROUP ccmMIBNotificationsGroup1
DESCRIPTION
"The ccmMIBNotificationsGroup is optional."
OBJECT callHomeDestProfileTrnsprtMthd
SYNTAX INTEGER {
email (1)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'email' needs to be supported."
OBJECT callHomeDestProfileMsgFormat
SYNTAX INTEGER {
shortText (3)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'shortText' needs to be supported."
OBJECT callHomeDestProfileStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
MIN-ACCESS read-only
DESCRIPTION
"Only 'active' needs to be supported."
OBJECT callHomeDestEmailAddress
SYNTAX SnmpAdminString (SIZE(1..63))
DESCRIPTION
"An implementation is only required to
support an address of size 1 to 63
octets."
OBJECT callHomeDestEmailAddressStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT ccmSmtpServersPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT ccmSmtpServersStatus
SYNTAX INTEGER {
active (1),
createAndGo (4),
destroy (6)
}
DESCRIPTION
"Only 'active', 'createAndGo' and 'destroy' needs
to be supported."
OBJECT callHomeEmailFrom
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
OBJECT callHomeEmailReplyTo
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
OBJECT callHomeEmailMsgDispNotification
SYNTAX SnmpAdminString (SIZE(0..63))
DESCRIPTION
"An implementation is only required to
support an address of size 0 to 63
octests."
::= { chMIBCompliances 4 }
chSystemInformationGroup OBJECT-GROUP
OBJECTS { sysContactPhoneNumber,
sysContactEmailAddress,
sysStreetAddress,
callHomeCustomerId,
callHomeContractId,
callHomeSiteId,
callHomeDeviceServicePriority
}
STATUS current
DESCRIPTION
"A collection of objects for displaying and
configuring system information pertaining to
CallHome."
::= { chMIBGroups 1 }
chConfigurationGroup OBJECT-GROUP
OBJECTS { callHomeEnable,
callHomeAlertAction,
callHomeAlertActionStatus,
callHomeAlertActionFailureCause,
callHomeDestProfileMsgFormat,
callHomeDestProfileMaxMsgSize,
callHomeDestProfileTrnsprtMthd,
callHomeDestProfileStatus,
callHomeEmailAddrTblMaxEntries,
callHomeDestEmailAddress,
callHomeDestEmailAddressStatus,
callHomeEmailFrom,
callHomeEmailReplyTo
}
STATUS deprecated
DESCRIPTION
"A collection of objects for displaying and
configuring CallHome parameters."
::= { chMIBGroups 2 }
chEmailMsgDispGroup OBJECT-GROUP
OBJECTS { callHomeEmailMsgDispNotification
}
STATUS current
DESCRIPTION
"A collection of object(s) for displaying and
configuring e-mail address to which the
e-mail disposition notification should be sent."
::= { chMIBGroups 3 }
chSingleSmtpServerGroup OBJECT-GROUP
OBJECTS { callHomeSmtpServerAddrType,
callHomeSmtpServerAddr,
callHomeSmtpServerPort
}
STATUS current
DESCRIPTION
"A collection of objects for displaying and
configuring CallHome SMTP server on the devices which
support only one SMTP server."
::= { chMIBGroups 4 }
chMultipleSmtpServersGroup OBJECT-GROUP
OBJECTS { ccmSmtpServersTblMaxEntries,
ccmSmtpServersPort,
ccmSmtpServersStatus
}
STATUS current
DESCRIPTION
"A collection of objects for displaying and
configuring CallHome SMTP server on the devices which
support on one SMTP server."
::= { chMIBGroups 5 }
chStatisticsGroup OBJECT-GROUP
OBJECTS { callHomeLastAlertSent,
callHomeAlerts
}
STATUS current
DESCRIPTION
"A collection of objects for displaying
CallHome statistics."
::= { chMIBGroups 6 }
ccmSysLogSeverityGroup OBJECT-GROUP
OBJECTS { ccmSysLogSeverity
}
STATUS current
DESCRIPTION
"A collection of object(s) for displaying and
configuring CallHome syslog severity based on which
call home alerts may be issued."
::= { chMIBGroups 7 }
ccmMIBNotificationsConfigGroup OBJECT-GROUP
OBJECTS { ccmEnableSmtpServerNotif
}
STATUS current
DESCRIPTION
"A collection of objects for displaying and
configuring CallHome notifications."
::= { chMIBGroups 8 }
ccmMIBNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { ccmSmtpServerFailNotif
}
STATUS deprecated
DESCRIPTION
"A collection of notifications."
::= { chMIBGroups 9 }
chConfigurationGroup1 OBJECT-GROUP
OBJECTS { callHomeEnable,
callHomeAlertAction,
callHomeAlertActionStatus,
callHomeAlertActionFailureCause,
callHomeDestProfileMsgFormat,
callHomeDestProfileMaxMsgSize,
callHomeDestProfileTrnsprtMthd,
callHomeDestProfileStatus,
callHomeDestProfileMsgLevel,
callHomeDestProfileAlertGroups,
callHomeEmailAddrTblMaxEntries,
callHomeDestEmailAddress,
callHomeDestEmailAddressStatus,
callHomeEmailFrom,
callHomeEmailReplyTo,
callHomeAlertGroupName
}
STATUS deprecated
DESCRIPTION
"A collection of objects for displaying and
configuring CallHome parameters."
::= { chMIBGroups 10 }
ccmMIBNotificationsGroup1 NOTIFICATION-GROUP
NOTIFICATIONS { ccmSmtpServerFailNotif,
ccmAlertGroupTypeAddedNotif,
ccmAlertGroupTypeDeletedNotif
}
STATUS current
DESCRIPTION
"A collection of notifications."
::= { chMIBGroups 11 }
chConfigurationGroup2 OBJECT-GROUP
OBJECTS { callHomeEnable,
callHomeAlertAction,
callHomeAlertActionStatus,
callHomeAlertActionFailureCause,
callHomeDestProfileMsgFormat,
callHomeDestProfileMaxMsgSize,
callHomeDestProfileTrnsprtMthd,
callHomeDestProfileStatus,
callHomeDestProfileMsgLevel,
callHomeDestProfileAlertGroups,
callHomeEmailAddrTblMaxEntries,
callHomeDestEmailAddress,
callHomeDestEmailAddressStatus,
callHomeEmailFrom,
callHomeEmailReplyTo,
callHomeAlertGroupName,
ccmMsgThrottlingEnable
}
STATUS current
DESCRIPTION
"A collection of objects for displaying and
configuring CallHome parameters."
::= { chMIBGroups 12 }
chSwInventoryInfoGroup OBJECT-GROUP
OBJECTS { callHomeInventoryInfoName,
callHomeInventoryInfoValue,
ccmPeriodicSwInventoryMsgEnable,
ccmPeriodicSwInventoryTimeFrame
}
STATUS deprecated
DESCRIPTION
"A collection of objects for displaying and
configuring software inventory information."
::= { chMIBGroups 13 }
chPeriodicSwInventoryInfoGroup OBJECT-GROUP
OBJECTS { ccmPeriodicSwInventoryMsgEnable,
ccmPeriodicSwInventoryTimeFrame
}
STATUS current
DESCRIPTION
"A collection of objects for configuring
periodic software inventory information."
::= { chMIBGroups 14 }
chSwInventoryInfoGroup1 OBJECT-GROUP
OBJECTS { callHomeInventoryInfoName,
callHomeInventoryInfoValue
}
STATUS current
DESCRIPTION
"A collection of objects for displaying
software inventory information."
::= { chMIBGroups 15 }
END