CISCO-L2-TUNNEL-CONFIG-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Unsigned32,
Counter32
FROM SNMPv2-SMI
TruthValue
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
ifIndex
FROM IF-MIB
QosLayer2Cos
FROM CISCO-QOS-PIB-MIB
ciscoMgmt
FROM CISCO-SMI
;
ciscoL2TunnelConfigMIB MODULE-IDENTITY
LAST-UPDATED "200406090000Z"
ORGANIZATION "Cisco Systems Inc."
CONTACT-INFO
"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
Email: cs-lan-switch-snmp@cisco.com"
DESCRIPTION
"This MIB module is for layer 2 tunneling related configurations
on a device.
Tunneling allows separate local networks to be considered as
a single VLAN. These separate networks are connected via an
ISP, which will tunnel the packets from one network to another,
making it appear as if the two networks are actually just one."
REVISION "200406090000Z"
DESCRIPTION
"Change the description for cltcTunnelThresholdProtocolIndex.
Add the new groups cltcTunnelThresholdNotifsGroup and
cltcNotifsEnableGroup."
REVISION "200309030000Z"
DESCRIPTION
"Add a new object cltcTunnelDropStats. Remove the restriction
for enabling cltcDot1qTunnelMode from the description."
REVISION "200205311000Z"
DESCRIPTION
"Add SNMP support for 802.1q All Tagged (dot1q-all-tagged)
Per Port feature.
Dot1q-all-tagged feature is an enhancement to tag the packets
on the native vlan to avoid any confusion in the ISP network,
and to avoid vlan hopping when the native vlan for the trunk
is as same as the vlan assigned for a customer.
Before this enhancement, this feature can be enabled/disabled
globally through the vlanTrunkPortsDot1qTag object in
CISCO-VTP-MIB. With this enhacement, vlanTrunkPortsDot1qTag
object in CISCO-VTP-MIB is deprecated and replaced by the
dot1qAllTaggedEnabled object in this MIB. Additionally,
dot1q-all-tag will be able to configure per port basis."
REVISION "200202140000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 246 }
cltcMIBObjects OBJECT IDENTIFIER ::= { ciscoL2TunnelConfigMIB 1 }
cltcGlobal OBJECT IDENTIFIER ::= { cltcMIBObjects 1 }
cltcDot1qTunnel OBJECT IDENTIFIER ::= { cltcMIBObjects 2 }
cltcTunneledProtocol OBJECT IDENTIFIER ::= { cltcMIBObjects 3 }
cltcTunnelThreshold OBJECT IDENTIFIER ::= { cltcMIBObjects 4 }
cltcTunnelStatistics OBJECT IDENTIFIER ::= { cltcMIBObjects 5 }
cltcDot1qAllTagged OBJECT IDENTIFIER ::= { cltcMIBObjects 6 }
cltcTunnelCos OBJECT-TYPE
SYNTAX QosLayer2Cos
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the user priority of the tunneled PDUs and applies
to all ingress tunneling interfaces."
::= { cltcGlobal 1 }
cltcNotificationEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates whether the system will
generate the cltcTunnelDropThresholdExceeded and
cltcTunnelShutdownThresholdExceeded notifications."
::= { cltcGlobal 2 }
cltcDot1qTunnelTable OBJECT-TYPE
SYNTAX SEQUENCE OF CltcDot1qTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the dot1q tunnel
interfaces. Only dot1q tunneling capable interfaces are shown.
1Q-in-1Q will allow service providers to separate the traffic
of various customers within their infrastructure while the
customers appear to be on the same VLANs."
::= { cltcDot1qTunnel 1 }
cltcDot1qTunnelEntry OBJECT-TYPE
SYNTAX CltcDot1qTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about the dot1q tunnel. Only dot1q tunneling
capable interfaces are shown."
INDEX { ifIndex }
::= { cltcDot1qTunnelTable 1 }
CltcDot1qTunnelEntry ::=
SEQUENCE {
cltcDot1qTunnelMode INTEGER
}
cltcDot1qTunnelMode OBJECT-TYPE
SYNTAX INTEGER { enabled(1), disabled(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the dot1q tunnel mode of the interface.
Setting the interface to dot1q tunnel 'disabled' mode causes
the dot1q tunnel feature to be disabled on this interface.
Setting the interface to dot1q tunnel 'enabled' mode causes
the dot1q tunnel feature to be enabled on this interface."
DEFVAL { disabled }
::= { cltcDot1qTunnelEntry 1 }
cltcTunneledProtocolTable OBJECT-TYPE
SYNTAX SEQUENCE OF CltcTunneledProtocolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the protocols being
tunneled. Only tunneled protocol filtering capable interfaces
are shown."
::= { cltcTunneledProtocol 1 }
cltcTunneledProtocolEntry OBJECT-TYPE
SYNTAX CltcTunneledProtocolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about the protocols being tunneled. Only tunneled
protocol filtering capable interfaces are shown."
INDEX { ifIndex }
::= { cltcTunneledProtocolTable 1 }
CltcTunneledProtocolEntry ::=
SEQUENCE {
cltcTunneledProtocolType BITS
}
cltcTunneledProtocolType OBJECT-TYPE
SYNTAX BITS { cdp(0), vtp(1), stp(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates tunneled protocol of the interface. This object can
only be applied to access interfaces.
If a BIT is set, then the value of the corresponding
protocol is tunneled. Specifically, if the 'cdp(0)'
BIT is set, then the Cisco Discovery Protocol PDU is
tunneled; if the 'vtp(1)' BIT is set, then the VLAN
Trunking Protocol PDU is tunneled; if the 'stp(2)' BIT
is set, then the Spanning Tree Protocol PDU is tunneled.
If the bit for a given protocol is cleared for an interface,
then the statistics for that interface and protocol are cleared.
If the bit for a given protocol is set for an interface, then
the statistics for that interface and protocol will start to be
monitored"
::= { cltcTunneledProtocolEntry 1 }
cltcTunnelThresholdTable OBJECT-TYPE
SYNTAX SEQUENCE OF CltcTunnelThresholdEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the thresholds for
protocol tunneling. Only tunneled protocol filtering capable
interfaces are shown. The objects will be on a per interface,
per protocol basis."
::= { cltcTunnelThreshold 1 }
cltcTunnelThresholdEntry OBJECT-TYPE
SYNTAX CltcTunnelThresholdEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about the thresholds for protocol tunneling. Only
tunneled protocol filtering capable interfaces are shown. The
entries will be on a per interface, per protocol basis"
INDEX { ifIndex,
cltcTunnelThresholdProtocolIndex }
::= { cltcTunnelThresholdTable 1 }
CltcTunnelThresholdEntry ::=
SEQUENCE {
cltcTunnelThresholdProtocolIndex INTEGER,
cltcTunnelDropThreshold Unsigned32,
cltcTunnelShutdownThreshold Unsigned32
}
cltcTunnelThresholdProtocolIndex OBJECT-TYPE
SYNTAX INTEGER {
all(1),
cdp(2),
vtp(3),
stp(4)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A tunneled protocol of an interface.
- all(1) is supported for devices which allow the setting
of thresholds on a per interface basis. This threshold is
a combined threshold for the interface which includes all
protocols.
- cdp(2), vtp(3), stp(4) are supported for devices which allow
the setting of thresholds on a per interface, per protocol
basis."
::= { cltcTunnelThresholdEntry 1 }
cltcTunnelDropThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "PDUs/sec"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The drop threshold on an interface for a given protocol. After
reaching this drop threshold, the interface will start dropping
PDUs for the given protocol. This value cannot be greater than
the value of cltcTunnelShutdownThreshold. A value of 0
indicates that no limit is set."
DEFVAL { 0 }
::= { cltcTunnelThresholdEntry 2 }
cltcTunnelShutdownThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "PDUs/sec"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The shutdown threshold on an interface for a given protocol.
After reaching the shutdown threshold, the interface will
shutdown for the given protocol. The statistics for the given
interface and protocol will be cleared. This value cannot be
less than the value of cltcTunnelDropThreshold. A value of 0
indicates that no limit is set."
DEFVAL { 0 }
::= { cltcTunnelThresholdEntry 3 }
cltcTunnelStatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CltcTunnelStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains protocol tunneling statistics on the
interface."
::= { cltcTunnelStatistics 1 }
cltcTunnelStatisticsEntry OBJECT-TYPE
SYNTAX CltcTunnelStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Protocol tunneling statistics on the interface."
INDEX { ifIndex,
cltcTunneledProtocolIndex }
::= { cltcTunnelStatisticsTable 1 }
CltcTunnelStatisticsEntry ::=
SEQUENCE {
cltcTunneledProtocolIndex INTEGER,
cltcTunnelEncapStats Counter32,
cltcTunnelDeEncapStats Counter32,
cltcTunnelDropStats Counter32
}
cltcTunneledProtocolIndex OBJECT-TYPE
SYNTAX INTEGER {
cdp(2),
vtp(3),
stp(4)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A tunneled protocol of an interface."
::= { cltcTunnelStatisticsEntry 1 }
cltcTunnelEncapStats OBJECT-TYPE
SYNTAX Counter32
UNITS "encapsulated PDUs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The tunneled PDU encapsulation statistics of an interface.
These statistics cover the number of tunneled ingress
PDUs."
::= { cltcTunnelStatisticsEntry 2 }
cltcTunnelDeEncapStats OBJECT-TYPE
SYNTAX Counter32
UNITS "de-encapsulated PDUs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The tunneled PDU de-encapsulation statistics of an interface.
These statistics cover the number of tunneled egress PDUs."
::= { cltcTunnelStatisticsEntry 3 }
cltcTunnelDropStats OBJECT-TYPE
SYNTAX Counter32
UNITS "PDUs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PDUs dropped on an interface for a given
protocol. The PDUs will be dropped when the
cltcTunnelDropThreshold is reached."
::= { cltcTunnelStatisticsEntry 4 }
cltcDot1qAllTaggedEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls if dot1q-all-tagged feature is enabled in
the managed system."
::= { cltcDot1qAllTagged 1 }
cltcDot1qAllTaggedIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF CltcDot1qAllTaggedIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the dot1q-all-tagged
feature's configuration of capable interfaces in the system."
::= { cltcDot1qAllTagged 2 }
cltcDot1qAllTaggedIfEntry OBJECT-TYPE
SYNTAX CltcDot1qAllTaggedIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration of dot1q-all-tagged feature on interfaces. Each
entry is created for a dot1q-all-tagged capable interface in
the system."
INDEX { ifIndex }
::= { cltcDot1qAllTaggedIfTable 1}
CltcDot1qAllTaggedIfEntry ::=
SEQUENCE {
cltcDot1qAllTaggedIfEnabled TruthValue
}
cltcDot1qAllTaggedIfEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether dot1q-all-tagged feature has been
enabled on a specific interface."
::= { cltcDot1qAllTaggedIfEntry 1 }
cltcMIBNotifications
OBJECT IDENTIFIER ::= { ciscoL2TunnelConfigMIB 2 }
cltcMIBNotificationsPrefix
OBJECT IDENTIFIER ::= { cltcMIBNotifications 0 }
cltcTunnelDropThresholdExceeded NOTIFICATION-TYPE
OBJECTS { cltcTunnelDropThreshold }
STATUS current
DESCRIPTION
"This notification is generated when the
cltcTunnelDropThreshold has been exceeded."
::= { cltcMIBNotificationsPrefix 1 }
cltcTunnelShutdownThresholdExceeded NOTIFICATION-TYPE
OBJECTS { cltcTunnelShutdownThreshold }
STATUS current
DESCRIPTION
"This notification is generated when the
cltcTunnelShutdownThreshold has been exceeded."
::= { cltcMIBNotificationsPrefix 2 }
cltcMIBConformance OBJECT IDENTIFIER ::= { ciscoL2TunnelConfigMIB 3 }
cltcMIBCompliances OBJECT IDENTIFIER ::= { cltcMIBConformance 1 }
cltcMIBGroups OBJECT IDENTIFIER ::= { cltcMIBConformance 2 }
cltcMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB."
MODULE
GROUP cltcDot1qTunnelGroup
DESCRIPTION
"A collection of objects for configuring dot1q tunnneling.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunneledProtocolGroup
DESCRIPTION
"A collection of objects for configuring tunneled protocols.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunnelThresholdGroup
DESCRIPTION
"A collection of objects for configuring the thresholds for
protocol tunneling. This group is mandatory only in devices
which support protocol tunneling."
GROUP cltcTunnelStatisticsGroup
DESCRIPTION
"A collection of objects which give the statistics regarding
the tunneling interfaces. This group is mandatory only in
devices which support tunneling statistics."
::= { cltcMIBCompliances 1 }
cltcMIBCompliance2 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB."
MODULE
GROUP cltcDot1qTunnelGroup
DESCRIPTION
"A collection of objects for configuring dot1q tunnneling.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunneledProtocolGroup
DESCRIPTION
"A collection of objects for configuring tunneled protocols.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunnelThresholdGroup
DESCRIPTION
"A collection of objects for configuring the thresholds for
protocol tunneling. This group is mandatory only in devices
which support protocol tunneling."
GROUP cltcTunnelStatisticsGroup
DESCRIPTION
"A collection of objects which give the statistics regarding
the tunneling interfaces. This group is mandatory only in
devices which support tunneling statistics."
GROUP cltcDot1qAllTaggedGroup
DESCRIPTION
"This group is mandatory only in devices which support
dot1q-all-tagged feature."
OBJECT cltcDot1qAllTaggedEnabled
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT cltcDot1qAllTaggedIfEnabled
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { cltcMIBCompliances 2 }
cltcMIBCompliance3 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB."
MODULE
GROUP cltcDot1qTunnelGroup
DESCRIPTION
"A collection of objects for configuring dot1q tunnneling.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunneledProtocolGroup
DESCRIPTION
"A collection of objects for configuring tunneled protocols.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunnelThresholdGroup
DESCRIPTION
"A collection of objects for configuring the thresholds for
protocol tunneling. This group is mandatory only in devices
which support protocol tunneling."
GROUP cltcTunnelStatisticsGroup
DESCRIPTION
"A collection of objects which give the statistics regarding
the tunneling interfaces. This group is mandatory only in
devices which support tunneling statistics."
GROUP cltcDot1qAllTaggedGroup
DESCRIPTION
"This group is mandatory only in devices which support
dot1q-all-tagged feature."
GROUP cltcTunnelDropStatisticsGroup
DESCRIPTION
"A collection of objects which give the statistics regarding
dropped PDUs on the tunneling interfaces. This group is
mandatory only in devices which support tunneling drop
statistics."
OBJECT cltcDot1qAllTaggedEnabled
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT cltcDot1qAllTaggedIfEnabled
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { cltcMIBCompliances 3 }
cltcMIBCompliance4 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the CISCO-L2-TUNNEL-CONFIG-MIB."
MODULE
GROUP cltcDot1qTunnelGroup
DESCRIPTION
"A collection of objects for configuring dot1q tunnneling.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunneledProtocolGroup
DESCRIPTION
"A collection of objects for configuring tunneled protocols.
This group is mandatory only in devices which support dot1q
tunneling."
GROUP cltcTunnelThresholdGroup
DESCRIPTION
"A collection of objects for configuring the thresholds for
protocol tunneling. This group is mandatory only in devices
which support protocol tunneling."
GROUP cltcTunnelStatisticsGroup
DESCRIPTION
"A collection of objects which give the statistics regarding
the tunneling interfaces. This group is mandatory only in
devices which support tunneling statistics."
GROUP cltcDot1qAllTaggedGroup
DESCRIPTION
"This group is mandatory only in devices which support
dot1q-all-tagged feature."
GROUP cltcTunnelDropStatisticsGroup
DESCRIPTION
"A collection of objects which give the statistics regarding
dropped PDUs on the tunneling interfaces. This group is
mandatory only in devices which support tunneling drop
statistics."
GROUP cltcNotifsEnableGroup
DESCRIPTION
"A collections of objects used to enable notifications.
This group is mandatory only in devices which support
the protocol tunneling notification feature."
GROUP cltcTunnelThresholdNotifsGroup
DESCRIPTION
"A collection of notifications used for the tunnel
thresholds. This group is mandatory only in devices
which support the protocol tunneling notification
feature."
OBJECT cltcDot1qAllTaggedEnabled
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT cltcDot1qAllTaggedIfEnabled
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { cltcMIBCompliances 4 }
cltcDot1qTunnelGroup OBJECT-GROUP
OBJECTS {
cltcDot1qTunnelMode
}
STATUS current
DESCRIPTION
"A collection of objects for configuring dot1q tunnneling."
::= { cltcMIBGroups 1 }
cltcTunneledProtocolGroup OBJECT-GROUP
OBJECTS {
cltcTunneledProtocolType,
cltcTunnelCos
}
STATUS current
DESCRIPTION
"A collection of objects for configuring tunneled protocols."
::= { cltcMIBGroups 2 }
cltcTunnelThresholdGroup OBJECT-GROUP
OBJECTS {
cltcTunnelDropThreshold,
cltcTunnelShutdownThreshold
}
STATUS current
DESCRIPTION
"A collection of objects for configuring the thresholds for
protocol tunneling."
::= { cltcMIBGroups 3 }
cltcTunnelStatisticsGroup OBJECT-GROUP
OBJECTS {
cltcTunnelEncapStats,
cltcTunnelDeEncapStats
}
STATUS current
DESCRIPTION
"A collection of objects which give the statistics regarding
the tunneling interfaces."
::= { cltcMIBGroups 4 }
cltcDot1qAllTaggedGroup OBJECT-GROUP
OBJECTS {
cltcDot1qAllTaggedEnabled,
cltcDot1qAllTaggedIfEnabled
}
STATUS current
DESCRIPTION
"A collection of objects for configuring the dot1q-all-tagged
feature in the system."
::= { cltcMIBGroups 5 }
cltcTunnelDropStatisticsGroup OBJECT-GROUP
OBJECTS {
cltcTunnelDropStats
}
STATUS current
DESCRIPTION
"A collection of objects which give the statistics regarding
dropped PDUs on the tunneling interfaces."
::= { cltcMIBGroups 6 }
cltcNotifsEnableGroup OBJECT-GROUP
OBJECTS {
cltcNotificationEnable
}
STATUS current
DESCRIPTION
"A collections of objects used to enable notifications."
::= { cltcMIBGroups 7 }
cltcTunnelThresholdNotifsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
cltcTunnelDropThresholdExceeded,
cltcTunnelShutdownThresholdExceeded
}
STATUS current
DESCRIPTION
"A collection of notifications used for the tunnel
thresholds."
::= { cltcMIBGroups 8 }
END