CISCO-VOICE-DIAL-CONTROL-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
IpAddress,
Gauge32,
Integer32
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
DisplayString,
RowStatus,
TruthValue
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
callActiveSetupTime,
callActiveIndex,
AbsoluteCounter32
FROM DIAL-CONTROL-MIB
cCallHistoryIndex,
cCallHistoryCallOrigin
FROM CISCO-DIAL-CONTROL-MIB
CvcSpeechCoderRate,
CvcFaxTransmitRate,
CvcCoderTypeRate,
CvcGUid,
CvcInBandSignaling,
cvCommonDcCallHistoryCoderTypeRate
FROM CISCO-VOICE-COMMON-DIAL-CONTROL-MIB
QosService
FROM INT-SERV-MIB
ifIndex,
InterfaceIndexOrZero
FROM IF-MIB
InetAddressType,
InetAddress
FROM INET-ADDRESS-MIB
DnisMapname
FROM CISCO-VOICE-DNIS-MIB
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
ciscoMgmt
FROM CISCO-SMI;
ciscoVoiceDialControlMIB MODULE-IDENTITY
LAST-UPDATED "200401200000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W. Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-voice@cisco.com"
DESCRIPTION
"This MIB module enhances the IETF Dial Control MIB
(RFC2128) by providing management of voice telephony
peers on both a circuit-switched telephony network,
and an IP data network.
"
REVISION "200401200000Z"
DESCRIPTION
"Added object cvVoIPCallActiveSRTPEnable to
cvVoIPCallActiveTable and cvVoIPCallHistorySRTPEnable
to cvVoIPCallHistoryTable to indicate whether SRTP is
enabled on a call.
"
REVISION "200306260000Z"
DESCRIPTION
"Modified the DEVAL definition of
cvVoIPPeerCfgDigitRelay object based on
no bit field was enabled when the object
was created.
"
REVISION "200304140000Z"
DESCRIPTION
"The DESCRIPTION of the following objects was
modified to specify the allowable characters
cvPeerCommonCfgSourceTrunkGrpLabel
cvPeerCommonCfgTargetTrunkGrpLabel
cvPeerCommonCfgSourceCarrierId
cvPeerCommonCfgTargetCarrierId.
"
REVISION "200212310000Z"
DESCRIPTION
"The following values were added to the
cvVoicePeerCfgEchoCancellerTest object:
echoCancellerG168Test4,
echoCancellerG168Test6,
echoCancellerG168Test9
"
REVISION "200212020000Z"
DESCRIPTION
"The range of the following objects was changed:
cvCallActiveNoiseLevel
cvCallActiveACOMLevel
cvCallActiveOutSignalLevel
cvCallActiveInSignalLevel
cvVoIPCallHistoryIcpif
"
REVISION "200210310000Z"
DESCRIPTION
"Add object cvVoIPPeerCfgMediaSetting to the table.
This object defines whether IP-IP media streams will
flow-through or flow-around the Gateway.
Add two new objects cvVoIPPeerCfgDesiredQoSVideo and
cvVoIPPeerCfgMinAcceptableQoSVideo to the table
cvVoIPPeerCfgTable. Also added objects
cvCallActiveAccountCode and cvCallHistoryAccountCode.
Depreciating element cvCallActiveERLLevel
Adding New element cvCallActiveERLLevelRev1
Adding New type sipNotify in cvVoIPPeerCfgDigitRelay
Adding New element cvVoIPPeerCfgRedirectip2ip in
CvVoIPPeerCfgEntry
"
REVISION "200207120000Z"
DESCRIPTION
" * Add a new cvPeerCfgPeerType object to define the
peer type
* Added rtpNte, a new value for the
cvVoIPPeerCfgDigitRelay object.
"
REVISION "200108200000Z"
DESCRIPTION
"Addition of the following objects:
cvVoIPCallActiveUsername
cvVoIPCallActiveProtocolCallId
cvVoIPCallActiveRemSigIPAddrT
cvVoIPCallActiveRemSigIPAddr
cvVoIPCallActiveRemSigPort
cvVoIPCallActiveRemMediaIPAddrT
cvVoIPCallActiveRemMediaIPAddr
cvVoIPCallActiveRemMediaPort
cvVoIPCallHistoryUsername
cvVoIPCallHistoryProtocolCallId
cvVoIPCallHistoryRemSigIPAddrT
cvVoIPCallHistoryRemSigIPAddr
cvVoIPCallHistoryRemSigPort
cvVoIPCallHistoryRemMediaIPAddrT
cvVoIPCallHistoryRemMediaIPAddr
cvVoIPCallHistoryRemMediaPort
cvdcPoorQoVNotificationRev1
Deprecation of the following objects:
cvVoIPCallActiveRemoteIPAddress
cvVoIPCallActiveRemoteUDPPort
cvVoIPCallHistoryRemoteIPAddress
cvVoIPCallHistoryRemoteUDPPort
cvdcPoorQoVNotification
"
REVISION "200107020000Z"
DESCRIPTION
"Add two new objects cvPeerCommonCfgSourceTrunkGrpLabel and
cvPeerCommonCfgTargetTrunkGrpLabel.
"
REVISION "200104100000Z"
DESCRIPTION
"[1] Add a new object for handling the following feature:
Location in milliseconds of largest amplitude reflector
detected by echo canceller in call active table.
Add new object for specifying an echo canceller test to
to be run when a call using a dial peer so configured is
connected.
[2] Change QosService import from INT-SERV-MIB to
INTEGRATED-SERVICES-MIB, since INTEGRATED-SERVICES-MIB
(RFC2213) is where QosService is defined.
"
REVISION "200103250000Z"
DESCRIPTION
"Add two new objects cvPeerCommonCfgSourceCarrierId and
cvPeerCommonCfgTargetCarrierId. Add a enum definition to
cvVoIPPeerCfgSessionTarget object.
"
REVISION "200005040000Z"
DESCRIPTION
"Add new objects for handling the following features:
[1] Calling Name display for call active and history table.
[2] Caller ID Block, which indicates whether the Caller ID
feature is in using, for call active and history table.
"
REVISION "200004190000Z"
DESCRIPTION
"Changed VoIP dialpeer default values for
Icpif to 20
ExpectFactor to 0
"
REVISION "200003130000Z"
DESCRIPTION
"Adding a new object cvPeerCommonCfgDnisMappingName.
"
REVISION "9906280000Z"
DESCRIPTION
"Moved common Textual Conventions and the following items in
the VoIP Call Active and Call History tables to the
CISCO-VOICE-COMMON-DIAL-CONTROL-MIB, as these items apply to
multiple network encapsulations.
CoderTypeRate
VADEnable
Added new objects for handling the following features:
[1] Gatekeeper registration configuration for voice peer
destination pattern.
[2] Dialpeer huntstop configuration.
[3] Voip configuration support for Coder Bytes, Fax Bytes,
settlement server and inband signaling.
Added the following objects to the cvdcPoorQoVNotification.
cvVoIPCallHistoryRemoteIPAddress,
cCallHistoryCallOrigin,
cvCommonDcCallHistoryCoderTypeRate
"
REVISION "9901290000Z"
DESCRIPTION
"Add new enums in cvVoIPPeerCfgDigitRelay object for
handling the transmission of dtmf digits across an
H.245 channel via the signal and alphanumeric fields.
"
REVISION "9809110000Z"
DESCRIPTION
"Add new objects for handling the following features:
[1] FAX page count for call active and history table.
[2] Peer Preference for peer configuration.
[3] Add FAX rate 12000 bps, G723.1 Annex A codec support.
[4] Technology prefix for VoIP encapsulated peer
configuration.
[5] Modify cvCallActiveACOMLeve, cvCallActiveERLLevel and
cvCallHistoryACOMLevel to support undeterminable state.
[6] Add digit relay configuration feature.
"
REVISION "9802220000Z"
DESCRIPTION
"Add new objects for handling the following:
[1] DNIS number matching.
[2] Maximum connection to/from peer.
[3] DID call treatment enable/disable.
[4] Dial peer association to lower layer interfaces with
CAS group.
[5] Lost/Ealy/Late voice packets object in both call active
and call history tables.
[6] Update compliance statements.
"
::= { ciscoMgmt 63 }
CvSessionProtocol ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents a Session Protocol used by Voice calls between a
local and remote router via the IP backbone.
other - none of the following.
cisco - cisco proprietary H.323 Lite session protocol.
sdp - Session Description Protocol.
sip - Session Initiation Protocol.
"
SYNTAX INTEGER {
other (1),
cisco (2),
sdp (3),
sip (4),
multicast (5)
}
CvCasGroup ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The Channel Associated Signalling Group of a
T1/E1. The valid CAS group range is from 0 to 23 for T1
and from 0 to 30 for E1. The value -1 indicates CAS group is
disabled.
"
SYNTAX Integer32 (-1..30)
cvdcMIBObjects OBJECT IDENTIFIER ::= { ciscoVoiceDialControlMIB 1 }
cvGeneralConfiguration OBJECT IDENTIFIER ::= { cvdcMIBObjects 1 }
cvPeer OBJECT IDENTIFIER ::= { cvdcMIBObjects 2 }
cvGatewayCallActive OBJECT IDENTIFIER ::= { cvdcMIBObjects 3 }
cvGatewayCallHistory OBJECT IDENTIFIER ::= { cvdcMIBObjects 4 }
cvGeneralPoorQoVNotificationEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates whether cvdcPoorQoVNotification (or
the newer cvdcPoorQoVNotificationRev1) traps should be
generated for a poor quality of voice calls.
If the value of this object is 'true',
cvdcPoorQoVNotification (or the newer
cvdcPoorQoVNotificationRev1) traps will be generated
for all voice over IP peers when a poor quality of voice
call condition is detected after the voice gateway call
disconnection. If the value of this object is 'false',
cvdcPoorQoVNotification (or the newer
cvdcPoorQoVNotificationRev1) traps will be generated only
for calls for which the
cvVoIPPeerCfgPoorQoVNotificationEnable object of voice
over IP peers having set to 'true'."
DEFVAL { false }
::= { cvGeneralConfiguration 1 }
cvPeerCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvPeerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table contains the Voice Generic Peer information that
is used to create an ifIndexed row with an appropriate
ifType that is associated with the cvPeerCfgType and
cvPeerCfgPeerType objects.
"
::= { cvPeer 1 }
cvPeerCfgEntry OBJECT-TYPE
SYNTAX CvPeerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single voice generic Peer. The creation of this
entry will create an associated ifEntry with an ifType
that is associated with cvPeerCfgType, i.e., for
'voiceEncap' encapsulation, an ifEntry will contain an
ifType voiceEncap(103); for 'voiceOverIp' encapsulation,
an ifEntry will contain an ifType voiceOverIp(104). The
ifAdminStatus of the newly created ifEntry is set to 'up'
and ifOperStatus is set to 'down'. In addition, an
associated voiceEncap/voiceOverIp Peer configuration
entry is created after the successful ifEntry creation.
Then ifIndex of the newly created ifEntry must be used by
the network manager to create a peer configuration entry
of IETF Dial Control MIB (Refer to RFC 2128 section
2.2.3.1 and the description of dialCtlPeerCfgEntry for the
detailed information).
In summary, the voice dial peer creation steps are as
follows:
[1] create this entry (voice/data generic peer entry).
[2] read the cvPeerCfgIfIndex of this entry for the
ifIndex of newly created voice/data generic peer.
[3] create the dialCtlPeerCfgEntry of RFC 2128 with the
indices of dialCtlPeerCfgId and the ifIndex of newly
created voice generic peer.
For each VoIP peer, it uses IP address and UDP port with
RTP protocol to transfer voice packet. Therefore, it does
not have its lower layer interface. The
dialCtlPeerCfgIfType object of IETF Dial Control MIB must
set to 'other' and the dialCtlPeerCfgLowerIf must set to
'0'.
After the successful creation of peer configuration entry
of IETF Dial Control MIB, the dial plan software in
managed device will set the ifOperStatus of the newly
created voiceEncap/voiceOverIp ifEntry to 'up' for
enabling the peer function if the peer configuration is
completed.
When this entry is deleted, its associated ifEntry,
voiceEncap/voiceOverIp specific peer entry and the peer
entry of IETF Dial Control MIB are deleted.
"
INDEX { cvPeerCfgIndex }
::= { cvPeerCfgTable 1 }
CvPeerCfgEntry ::= SEQUENCE {
cvPeerCfgIndex Integer32,
cvPeerCfgIfIndex InterfaceIndexOrZero,
cvPeerCfgType INTEGER,
cvPeerCfgRowStatus RowStatus,
cvPeerCfgPeerType INTEGER
}
cvPeerCfgIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary index that uniquely identifies a generic
voice peer."
::= { cvPeerCfgEntry 1 }
cvPeerCfgIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of the peer associated ifEntry. The ifIndex
appears after the associated ifEntry is created
successfully.
This ifIndex will be used to access the objects in the
Voice over Telephony or Voice over IP peer specific table.
In addition, the ifIndex is also used to access the
associated peer configuration entry of the IETF Dial
Control MIB. If the peer associated ifEntry had not been
created, then this object has a value of zero.
"
::= { cvPeerCfgEntry 2 }
cvPeerCfgType OBJECT-TYPE
SYNTAX INTEGER {
voice (1),
voip (2),
mmail (3),
voatm (4),
vofr (5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the type of voice related encapsulation.
voice - voice encapsulation (voiceEncap ifType) on the
telephony network.
voip - VoIP encapsulation (voiceOverIp ifType) on the IP
network.
mmail - Media Mail over IP encapsulation (mediaMailOverIp
ifType) on the IP network.
voatm - VoATM encapsulation (voiceOverATM ifType) on the
ATM network.
vofr - VoFR encapsulation (voiceOverFR ifType) on the
Frame Relay network.
"
DEFVAL { voice }
::= { cvPeerCfgEntry 3 }
cvPeerCfgRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object is used to create a new row or modify or
delete an existing row in this table.
"
::= { cvPeerCfgEntry 4 }
cvPeerCfgPeerType OBJECT-TYPE
SYNTAX INTEGER {
voice (1),
data (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the type of a peer.
voice - peer in voice type to be defined in a voice
gateway for voice calls.
data - peer in data type to be defined in gateway
that supports universal ports for modem/data
calls.
"
DEFVAL { voice }
::= { cvPeerCfgEntry 5 }
cvVoicePeerCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvVoicePeerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table contains the Voice over Telephony peer specific
information that is required to accept voice calls or to
which it will place them or perform various loopback tests
via interface.
"
::= { cvPeer 2 }
cvVoicePeerCfgEntry OBJECT-TYPE
SYNTAX CvVoicePeerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Voice specific Peer. One entry per voice
encapsulation.
The entry is created when its associated 'voiceEncap(103)'
encapsulation ifEntry is created.
This entry is deleted when its associated ifEntry is
deleted.
"
INDEX { ifIndex }
::= { cvVoicePeerCfgTable 1 }
CvVoicePeerCfgEntry ::= SEQUENCE {
cvVoicePeerCfgSessionTarget DisplayString,
cvVoicePeerCfgDialDigitsPrefix DisplayString,
cvVoicePeerCfgDIDCallEnable TruthValue,
cvVoicePeerCfgCasGroup CvCasGroup,
cvVoicePeerCfgRegisterE164 TruthValue,
cvVoicePeerCfgForwardDigits Integer32,
cvVoicePeerCfgEchoCancellerTest INTEGER
}
cvVoicePeerCfgSessionTarget OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the session target of the peer.
Session Targets definitions:
The session target has the syntax used by the IETF service
location protocol. The syntax is as follows:
mapping-type:type-specific-syntax
the mapping-type specifies a scheme for mapping the
matching dial string to a session target.
The valid Mapping type definitions for the peer are as
follows:
loopback - Syntax: loopback:where
'where' string is defined as follows:
compressed - loopback is performed on compressed voice
as close to the CODEC which processes the
data as possible.
uncompressed - loopback is performed on the PCM or
analog voice as close to the telephony
endpoint as possible.
Local loopback case:
uncompressed - the PCM voice coming into the DSP is simply
turned around and sent back out, allowing testing of
the transmit--> receive paths in the telephony
endpoint.
compressed - the compressed voice coming out of the CODEC is
turned around on the DSP module and fed back into the
decompressor through the jitter buffer. In addition to
the telephony endpoint, this tests both the encode and
decode paths without involving data paths or packet
handling on the host router.
Remote loopback case:
compressed - RTP packets received from the network are
decapsulated and passed to the DSP board. Instead of
feeding these into the CODEC for decompression, they
are immediately sent back to the session application
as if they had originated locally and been compressed.
uncompressed - In addition to the above, the voice samples
are sent all the way through the CODEC and then turned
around instead of being sent to the telephony
endpoint
"
DEFVAL { "" }
::= { cvVoicePeerCfgEntry 1 }
cvVoicePeerCfgDialDigitsPrefix OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the prefix of the dial digits for the
peer. The dial digits prefix is sent to telephony
interface before the real phone number when the system
places the outgoing call to the voice encapsulation peer
over telephony interface.
"
DEFVAL { "" }
::= { cvVoicePeerCfgEntry 2 }
cvVoicePeerCfgDIDCallEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object enables/disables the DID call treatment for
incoming DNIS digits.
true - treat the incoming DNIS digits as if the digits
are received from DID trunk.
false - Disable DID call treatment for incoming DNIS
digits.
"
DEFVAL { false }
::= { cvVoicePeerCfgEntry 3 }
cvVoicePeerCfgCasGroup OBJECT-TYPE
SYNTAX CvCasGroup
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the CAS group number of a CAS
capable T1/E1 that is in the dialCtlPeerCfgLowerIf object
of RFC2128.
This object can be set to a valid CAS group number only if
the dialCtlPeerCfgLowerIf contains a valid ifIndex for a
CAS capable T1/E1. The object must set to -1 before the
value of the dialCtlPeerCfgLowerIf object of RFC2128 can
be changed.
"
DEFVAL { -1 }
::= { cvVoicePeerCfgEntry 4 }
cvVoicePeerCfgRegisterE164 OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies that the E.164 number specified in
the dialCtlPeerCfgOriginateAddress field of the associated
dialCtlPeerCfgTable entry be registered as an extension
phone number of this gateway for H323 gatekeeper and/or
SIP registrar.
"
DEFVAL { false }
::= { cvVoicePeerCfgEntry 5 }
cvVoicePeerCfgForwardDigits OBJECT-TYPE
SYNTAX Integer32 (-3..32)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the number of dialed digits to
forward to the remote destination in the setup message.
The object can take the value:
0-32 number of right justified digits to forward
-1 default
-2 forward extra digits i.e those over and above
those needed to match to the destination pattern
-3 forward all digits
"
DEFVAL { 0 }
::= { cvVoicePeerCfgEntry 6 }
cvVoicePeerCfgEchoCancellerTest OBJECT-TYPE
SYNTAX INTEGER {
echoCancellerTestNone (1),
echoCancellerG168Test2A (2),
echoCancellerG168Test2B (3),
echoCancellerG168Test2Ca (4),
echoCancellerG168Test2Cb (5),
echoCancellerG168Test3A (6),
echoCancellerG168Test3B (7),
echoCancellerG168Test3C (8),
echoCancellerG168Test4 (9),
echoCancellerG168Test6 (10),
echoCancellerG168Test9 (11)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies which, if any, test to run in the
echo canceller when a call from the network is connected.
echoCancellerTestNone - do not run a test.
echoCancellerG168Test2A - run ITU-T G.168 Test 2A.
echoCancellerG168Test2B - run ITU-T G.168 Test 2B.
echoCancellerG168Test2Ca - run ITU-T G.168 Test 2C(a).
echoCancellerG168Test2Cb - run ITU-T G.168 Test 2C(b).
echoCancellerG168Test3A - run ITU-T G.168 Test 3A.
echoCancellerG168Test3B - run ITU-T G.168 Test 3B.
echoCancellerG168Test3C - run ITU-T G.168 Test 3C.
echoCancellerG168Test4 - run ITU-T G.168 Test 4.
echoCancellerG168Test6 - run ITU-T G.168 Test 6.
echoCancellerG168Test9 - run ITU-T G.168 Test 9.
"
REFERENCE
"ITU-T G.168(04/2000): Section 6.4 Tests and requirements
for performance with input signals applied to the send and
receive paths.
"
DEFVAL { echoCancellerTestNone }
::= { cvVoicePeerCfgEntry 7 }
cvVoIPPeerCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvVoIPPeerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table contains the Voice over IP (VoIP) peer specific
information that is required to accept voice calls or to
which it will place them via IP backbone with the
specified session protocol in cvVoIPPeerCfgSessionProtocol.
"
::= { cvPeer 3 }
cvVoIPPeerCfgEntry OBJECT-TYPE
SYNTAX CvVoIPPeerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single VoIP specific Peer. One entry per VoIP
encapsulation.
The entry is created when its associated 'voiceOverIp(104)'
encapsulation ifEntry is created.
This entry is deleted when its associated ifEntry is
deleted.
"
INDEX { ifIndex }
::= { cvVoIPPeerCfgTable 1 }
CvVoIPPeerCfgEntry ::= SEQUENCE {
cvVoIPPeerCfgSessionProtocol CvSessionProtocol,
cvVoIPPeerCfgDesiredQoS QosService,
cvVoIPPeerCfgMinAcceptableQoS QosService,
cvVoIPPeerCfgSessionTarget DisplayString,
cvVoIPPeerCfgCoderRate CvcSpeechCoderRate,
cvVoIPPeerCfgFaxRate CvcFaxTransmitRate,
cvVoIPPeerCfgVADEnable TruthValue,
cvVoIPPeerCfgExpectFactor Integer32,
cvVoIPPeerCfgIcpif Integer32,
cvVoIPPeerCfgPoorQoVNotificationEnable TruthValue,
cvVoIPPeerCfgUDPChecksumEnable TruthValue,
cvVoIPPeerCfgIPPrecedence Integer32,
cvVoIPPeerCfgTechPrefix DisplayString,
cvVoIPPeerCfgDigitRelay BITS,
cvVoIPPeerCfgCoderBytes Integer32,
cvVoIPPeerCfgFaxBytes Integer32,
cvVoIPPeerCfgInBandSignaling CvcInBandSignaling,
cvVoIPPeerCfgMediaSetting INTEGER,
cvVoIPPeerCfgDesiredQoSVideo QosService,
cvVoIPPeerCfgMinAcceptableQoSVideo QosService,
cvVoIPPeerCfgRedirectip2ip TruthValue
}
cvVoIPPeerCfgSessionProtocol OBJECT-TYPE
SYNTAX CvSessionProtocol
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the session protocol to be used
for Internet call between local and remote router via
IP backbone.
"
DEFVAL { cisco }
::= { cvVoIPPeerCfgEntry 1 }
cvVoIPPeerCfgDesiredQoS OBJECT-TYPE
SYNTAX QosService
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the user requested Quality of Service
for the call.
"
DEFVAL { bestEffort }
::= { cvVoIPPeerCfgEntry 2 }
cvVoIPPeerCfgMinAcceptableQoS OBJECT-TYPE
SYNTAX QosService
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the minimally acceptable Quality of
Service for the call.
"
DEFVAL { bestEffort }
::= { cvVoIPPeerCfgEntry 3 }
cvVoIPPeerCfgSessionTarget OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the session target of the peer.
Session Targets definitions:
The session target has the syntax used by the IETF service
location protocol. The syntax is as follows:
mapping-type:type-specific-syntax
the mapping-type specifies a scheme for mapping the
matching dial string to a session target. The
type-specific-syntax is exactly that, something that the
particular mapping scheme can understand.
For example,
Session target Meaning
ipv4:171.68.13.55:1006 The session target is the IP
version 4 address of 171.68.13.55
and port 1006.
dns:pots.cisco.com:1661 The session target is the IP host
with dns name pots.cisco.com, and
port 1661.
ras The session target is the
gatekeeper with RAS (Registration
, Admission, Status protocol).
settlement The session target is the
settlement server.
enum:1 The session target is the enum
profile match table 1.
The valid Mapping type definitions for the peer are as
follows:
ipv4 - Syntax: ipv4:w.x.y.z:port or ipv4:w.x.y.z
dns - Syntax: dns:host.domain:port or
dns:host.domain
ras - Syntax: ras
settlement - Syntax: settlement
enum - Syntax: enum:<table#>
loopback - Syntax: loopback:where
'where' string is defined as follows:
rtp - loopback is performed at the transport protocol
level.
Local loopback case:
rtp - the session application sets up an RTP stream to
itself (i.e. actually allocates a port pair and opens
the appropriate UDP sockets). It then does the full
RTP encapsulation, sends the packets to the loopback
IP address, receives the RTP packets, and hands the
compressed voice back to the CODEC. This tests the
entire local processing path, both transmit and
receive, in the router, as well as all of the above
paths.
Remote loopback case:
rtp: RTP packets received from the network are decapsulated and
immediately re-encapsulated in the outbound RTP
stream, using the same media clock (i.e. timestamp)
as the received packet. They are then sent back to
the remote source router as if the voice had
originated on a telephony port on the local router.
"
DEFVAL { "" }
::= { cvVoIPPeerCfgEntry 4 }
cvVoIPPeerCfgCoderRate OBJECT-TYPE
SYNTAX CvcSpeechCoderRate
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the most desirable codec of speech
for the VoIP peer.
"
DEFVAL { g729IETFr8000 }
::= { cvVoIPPeerCfgEntry 5 }
cvVoIPPeerCfgFaxRate OBJECT-TYPE
SYNTAX CvcFaxTransmitRate
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" This object specifies the default transmit rate of FAX
the VoIP peer. If the value of this object is 'none',
then the Fax relay feature is disabled; otherwise the Fax
relay feature is enabled.
"
DEFVAL { voiceRate }
::= { cvVoIPPeerCfgEntry 6 }
cvVoIPPeerCfgVADEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether or not the VAD (Voice
Activity Detection) voice data is continuously transmitted
to IP backbone.
"
DEFVAL { true }
::= { cvVoIPPeerCfgEntry 7 }
cvVoIPPeerCfgExpectFactor OBJECT-TYPE
SYNTAX Integer32 (0..20)
UNITS "equipment impairment factor (eif)"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the user requested Expectation
Factor of voice quality for the call via this peer.
"
REFERENCE
"ITU G.113: Sections 8 Considerations Concerning the
Expectation Factor A.
"
DEFVAL { 0 }
::= { cvVoIPPeerCfgEntry 8 }
cvVoIPPeerCfgIcpif OBJECT-TYPE
SYNTAX Integer32 (0..55)
UNITS "equipment impairment factor (eif)"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the user requested Calculated
Planning Impairment Factor (Icpif) for the call via this
peer.
"
REFERENCE
"ITU G.113: Sections 9 Considerations associated with the
Calculated Planning Impairment Factor (Icpif)
"
DEFVAL { 20 }
::= { cvVoIPPeerCfgEntry 9 }
cvVoIPPeerCfgPoorQoVNotificationEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether cvdcPoorQoVNotification (or
the newer cvdcPoorQoVNotificationRev1) traps should be
generated for the call that is associated with this
peer."
DEFVAL { false }
::= { cvVoIPPeerCfgEntry 10 }
cvVoIPPeerCfgUDPChecksumEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the outgoing voice related
UDP packet contains a valid checksum value.
true - enable the checksum of outgoing voice UDP packets
false - disable the checksum of outgoing voice UDP packets
"
DEFVAL { false }
::= { cvVoIPPeerCfgEntry 11 }
cvVoIPPeerCfgIPPrecedence OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the value to be stored in the IP
Precedence field of voice packets, with values ranging
from 0 (normal precedence) through 7 (network control),
allowing the managed system to set the importance of each
voice packet for delivering them to the destination peer.
"
REFERENCE
"RFC 791: Section 3.1. Internet Header Format; Type of
Service.
"
DEFVAL { 0 }
::= { cvVoIPPeerCfgEntry 12 }
cvVoIPPeerCfgTechPrefix OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the technology prefix of the peer,
The technology prefix and the called party address
are passed in Admission Request (ARQ) to gatekeeper
for the called party address resolution during call setup.
"
REFERENCE
"ITU-T H.225.0: Section 7.6 Common Message Elements.
"
DEFVAL { "" }
::= { cvVoIPPeerCfgEntry 13 }
cvVoIPPeerCfgDigitRelay OBJECT-TYPE
SYNTAX BITS {
rtpCisco (0),
h245Signal (1),
h245Alphanumeric (2),
rtpNte (3),
sipNotify (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the methods to transmit dial digits
(DTMF or MF digits) via IP network.
rtpCisco - Enable capability to transmit dial digits
with Cisco proprietary RTP payload type.
h245Signal - Enable capability to transmit dtmf digits
across the H.245 channel, via the signal
field of the UserInputIndication message
h245Alphanumeric - Enable capability to transmit dtmf
digit across the H.245 channel, via the
string or alphanumeric fields of the
UserInputIndication message
rtpNte - Enable capability to transmit dial digits
using Named Telephony Event per RFC 2833
section 3.
sipNotify - Enable capability to transmit dtmf
digits using unsolicited SIP NOTIFY
messages. This mechanism is only available
for SIP dialpeers.
Modifying the value of cvVoIPPeerCfgSessionProtocol
can reset the digit-relay method associated bits value in
this object if the modified session protocol does not
support these digit-relay methods.
"
REFERENCE
"[1] ITU H.245: Section 6.
[2] RFC 2833 : Section 3.
"
DEFVAL { { } }
::= { cvVoIPPeerCfgEntry 14 }
cvVoIPPeerCfgCoderBytes OBJECT-TYPE
SYNTAX Integer32 (0 | 10..240)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the size of the voice payload sample
to be produced by the coder specified in
cvVoIPPeerCfgCoderRate.
Each coder sample produces 10 bytes of voice payload. The
specified value will be rounded down to the nearest valid
size.
A value of 0, specifies that the coder defined by
cvVoIPPeerCfgCoderRate should produce its default payload
size.
"
DEFVAL { 0 }
::= { cvVoIPPeerCfgEntry 15 }
cvVoIPPeerCfgFaxBytes OBJECT-TYPE
SYNTAX Integer32 (0 | 10..255)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the payload size to be produced by
the coder when it is generating fax data. A value of 0,
specifies that the coder specified in
cvVoIPCfgPeerCoderRate should produce its default fax
payload size.
"
DEFVAL { 0 }
::= { cvVoIPPeerCfgEntry 16 }
cvVoIPPeerCfgInBandSignaling OBJECT-TYPE
SYNTAX CvcInBandSignaling
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the type of in-band signaling that
will be used between the end points of the call. It is
used by the router to determine how to interpret ABCD
signaling bits sent as part of voice payload data.
"
DEFVAL { cas }
::= { cvVoIPPeerCfgEntry 17 }
cvVoIPPeerCfgMediaSetting OBJECT-TYPE
SYNTAX INTEGER {
flowThrough(1),
flowAround(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies how the media is to be setup on
an IP-IP Gateway. Two choices are valid: flow-through
and flow-around. When in flow-through mode, which is the
default setting, the IP-IP Gateway will terminate and
then re-originate the media stream. When flow-around
is configured the Gateway will not be involved with the
media, since it will flow-around the Gateway and will
be established directly between the endpoints.
"
DEFVAL { flowThrough }
::= { cvVoIPPeerCfgEntry 23 }
cvVoIPPeerCfgDesiredQoSVideo OBJECT-TYPE
SYNTAX QosService
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the user requested Quality of Service
for the video portion of the call.
"
DEFVAL { bestEffort }
::= { cvVoIPPeerCfgEntry 24 }
cvVoIPPeerCfgMinAcceptableQoSVideo OBJECT-TYPE
SYNTAX QosService
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the minimally acceptable Quality of
Service for the video portion of the call.
"
DEFVAL { bestEffort }
::= { cvVoIPPeerCfgEntry 25 }
cvVoIPPeerCfgRedirectip2ip OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Inbound VoIP calls that match
an outbound VoIP dialpeer will be responded with a SIP
redirect(for inbound SIP) or H.450.3 call-forward(for
inbound H.323).
"
DEFVAL { false }
::= { cvVoIPPeerCfgEntry 26 }
cvPeerCommonCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvPeerCommonCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table contains the Voice specific peer common
configuration information that is required to accept voice
calls or to which it will place them or process the
incoming calls.
"
::= { cvPeer 4 }
cvPeerCommonCfgEntry OBJECT-TYPE
SYNTAX CvPeerCommonCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Voice specific Peer. One entry per voice related
encapsulation.
The entry is created when a voice related encapsulation
ifEntry is created.
This entry is deleted when its associated ifEntry is
deleted.
"
INDEX { ifIndex }
::= { cvPeerCommonCfgTable 1 }
CvPeerCommonCfgEntry ::= SEQUENCE {
cvPeerCommonCfgIncomingDnisDigits DisplayString,
cvPeerCommonCfgMaxConnections Integer32,
cvPeerCommonCfgApplicationName DisplayString,
cvPeerCommonCfgPreference Integer32,
cvPeerCommonCfgHuntStop TruthValue,
cvPeerCommonCfgDnisMappingName DnisMapname,
cvPeerCommonCfgSourceCarrierId SnmpAdminString,
cvPeerCommonCfgTargetCarrierId SnmpAdminString,
cvPeerCommonCfgSourceTrunkGrpLabel SnmpAdminString,
cvPeerCommonCfgTargetTrunkGrpLabel SnmpAdminString
}
cvPeerCommonCfgIncomingDnisDigits OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the prefix of the incoming Dialed
Number Identification Service (DNIS) digits for the peer.
The DNIS digits prefix is used to match with the incoming
DNIS number for incoming call discrimination. If the
digits in this object are matched with incoming DNIS
number, the associated dialCtlPeerCfgInfoType in RFC 2128
will be used as a call discriminator for differentiating
speech, data, fax, video or modem calls.
"
DEFVAL { "" }
::= { cvPeerCommonCfgEntry 1 }
cvPeerCommonCfgMaxConnections OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
UNITS "connections"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the maximum allowed connection
to/from the peer. A value of -1 disables the limit of
maximum connections.
"
DEFVAL { -1 }
::= { cvPeerCommonCfgEntry 2 }
cvPeerCommonCfgApplicationName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the application to handle the incoming
call after the peer is selected.
If no application name is specified, then the default
session application will take care of the incoming call.
"
DEFVAL { "" }
::= { cvPeerCommonCfgEntry 3 }
cvPeerCommonCfgPreference OBJECT-TYPE
SYNTAX Integer32 (0..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the selection preference of a peer
when multiple peers are matched to the selection criteria.
The value of 0 has the lowest preference for peer
selection.
"
DEFVAL { 0 }
::= { cvPeerCommonCfgEntry 4 }
cvPeerCommonCfgHuntStop OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether dialpeer hunting should stop
when this peer is reached.
"
DEFVAL { false }
::= { cvPeerCommonCfgEntry 5 }
cvPeerCommonCfgDnisMappingName OBJECT-TYPE
SYNTAX DnisMapname
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies a Dialer Number Identification
Service (DNIS) map name for the Voice specific peer
entry specified in this row. A DNIS is a called party
number and they can be grouped and identified by DNIS
map.
"
DEFVAL { "" }
::= { cvPeerCommonCfgEntry 6 }
cvPeerCommonCfgSourceCarrierId OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the Source Carrier Id for the peer.
The Source Carrier Id is used to match with the Source
Carrier Id of a call. If the Source Carrier Id in this
object is matched with the Source Carrier Id of a call,
then the associated peer will be used to handle the call.
Only alphanumeric characters, '-' and '_' are allowed in
the string.
"
DEFVAL { "" }
::= { cvPeerCommonCfgEntry 7 }
cvPeerCommonCfgTargetCarrierId OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the Target Carrier Id for the peer.
The Target Carrier Id is used to match with the Target
Carrier Id of a call. If the Target Carrier Id in this
object is matched with the Target Carrier Id of a call,
then the associated peer will be used to handle the call.
Only alphanumeric characters, '-' and '_' are allowed in
the string.
"
DEFVAL { "" }
::= { cvPeerCommonCfgEntry 8 }
cvPeerCommonCfgSourceTrunkGrpLabel OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the Source Trunk Group Label for the
peer. The Source Trunk Group Label is used to match with
the Source Trunk Group Label of a call. If the Source
Trunk Group Label in this object is matched with the
Source Trunk Group Label of a call, then the associated
peer will be used to handle the call.
Only alphanumeric characters, '-' and '_' are allowed in
the string.
"
DEFVAL { "" }
::= { cvPeerCommonCfgEntry 9 }
cvPeerCommonCfgTargetTrunkGrpLabel OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the Target Trunk Group Label for the
peer. The Target Trunk Group Label is used to match with
the Target Trunk Group Label of a call. If the Target
Trunk Group Label in this object is matched with the
Target Trunk Group Label of a call, then the associated
peer will be used to handle the call.
Only alphanumeric characters, '-' and '_' are allowed in
the string.
"
DEFVAL { "" }
::= { cvPeerCommonCfgEntry 10 }
cvCallActiveTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvCallActiveEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is the voice extension to the call active table
of IETF Dial Control MIB. It contains voice encapsulation
call leg information that is derived from the statistics
of lower layer telephony interface.
"
::= { cvGatewayCallActive 1 }
cvCallActiveEntry OBJECT-TYPE
SYNTAX CvCallActiveEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The information regarding a single voice encapsulation
call leg.
The call leg entry is identified by using the same index
objects that are used by Call Active table of IETF Dial
Control MIB to identify the call.
An entry of this table is created when its associated call
active entry in the IETF Dial Control MIB is created and
call active entry contains the call establishment to a
voice over telephony network peer.
The entry is deleted when its associated call active entry
in the IETF Dial Control MIB is deleted.
"
INDEX { callActiveSetupTime, callActiveIndex }
::= { cvCallActiveTable 1 }
CvCallActiveEntry ::=
SEQUENCE {
cvCallActiveConnectionId CvcGUid,
cvCallActiveTxDuration AbsoluteCounter32,
cvCallActiveVoiceTxDuration AbsoluteCounter32,
cvCallActiveFaxTxDuration AbsoluteCounter32,
cvCallActiveCoderTypeRate CvcCoderTypeRate,
cvCallActiveNoiseLevel Integer32,
cvCallActiveACOMLevel Integer32,
cvCallActiveOutSignalLevel Integer32,
cvCallActiveInSignalLevel Integer32,
cvCallActiveERLLevel Integer32,
cvCallActiveSessionTarget DisplayString,
cvCallActiveImgPageCount AbsoluteCounter32,
cvCallActiveCallingName SnmpAdminString,
cvCallActiveCallerIDBlock TruthValue,
cvCallActiveEcanReflectorLocation Integer32,
cvCallActiveAccountCode SnmpAdminString,
cvCallActiveERLLevelRev1 Integer32
}
cvCallActiveConnectionId OBJECT-TYPE
SYNTAX CvcGUid
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The global call identifier for the gateway call."
::= { cvCallActiveEntry 1 }
cvCallActiveTxDuration OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of Transmit path open from this peer to the
voice gateway for the call leg. This counter object will
lock at the maximum value which is approximately two
days.
"
::= { cvCallActiveEntry 2 }
cvCallActiveVoiceTxDuration OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice transmitted from this peer to voice
gateway for this call leg. The Voice Utilization Rate can
be obtained by dividing this by cvCallActiveTXDuration
object. This counter object will lock at the maximum
value which is approximately two days.
"
::= { cvCallActiveEntry 3 }
cvCallActiveFaxTxDuration OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of fax transmitted from this peer to voice gateway
for this call leg. The FAX Utilization Rate can be
obtained by dividing this by cvCallActiveTXDuration
object. This counter object will lock at the maximum
value which is approximately two days.
"
::= { cvCallActiveEntry 4 }
cvCallActiveCoderTypeRate OBJECT-TYPE
SYNTAX CvcCoderTypeRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The negotiated coder rate. It specifies the transmit rate of
voice/fax compression to its associated call leg for the
call.
"
::= { cvCallActiveEntry 5 }
cvCallActiveNoiseLevel OBJECT-TYPE
SYNTAX Integer32 (-128..8)
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object contains the active noise level for the call
leg.
"
::= { cvCallActiveEntry 6 }
cvCallActiveACOMLevel OBJECT-TYPE
SYNTAX Integer32 (-1..127)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object contains the sum of Echo Return Loss (ERL),
cancellation loss (Echo Return Loss Enhancement) and
nonlinear processing loss for the call leg.
The value -1 indicates the level can not be determined or
level detection is disabled.
"
::= { cvCallActiveEntry 7 }
cvCallActiveOutSignalLevel OBJECT-TYPE
SYNTAX Integer32 (-128..8)
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object contains the active output signal level to
telephony interface that is used by the call leg.
"
::= { cvCallActiveEntry 8 }
cvCallActiveInSignalLevel OBJECT-TYPE
SYNTAX Integer32 (-128..8)
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object contains the active input signal level from
telephony interface that is used by the call leg.
"
::= { cvCallActiveEntry 9 }
cvCallActiveERLLevel OBJECT-TYPE
SYNTAX Integer32 (-1..45)
UNITS "dB"
MAX-ACCESS read-only
STATUS deprecated DESCRIPTION
"The object contains the current Echo Return Loss (ERL)
level for the call leg.
The value -1 indicates the level can not be determined or
level detection is disabled.
"
::= { cvCallActiveEntry 10 }
cvCallActiveSessionTarget OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object specifies the session target of the peer that
is used for the call leg. This object is set with the
information in the call associated
cvVoicePeerCfgSessionTarget object when the call is
connected.
"
::= { cvCallActiveEntry 11 }
cvCallActiveImgPageCount OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "pages"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of FAX related image pages are received or
transmitted via the peer for the call leg.
"
::= { cvCallActiveEntry 12 }
cvCallActiveCallingName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The calling party name of the call. If the name is
not available, then it will have a length of zero."
::= { cvCallActiveEntry 13 }
cvCallActiveCallerIDBlock OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object indicates whether or not the caller ID feature
is blocked for this call."
::= { cvCallActiveEntry 14 }
cvCallActiveEcanReflectorLocation OBJECT-TYPE
SYNTAX Integer32 (0..128)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The location in milliseconds of the largest amplitude
reflector detected by the echo canceller for this call.
The value 0 indicates there is no reflector or the
information is not available."
::= { cvCallActiveEntry 15 }
cvCallActiveAccountCode OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..50))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object indicates the account code input to the call.
It could be used for call screen or by down stream server
for billing purpose.
The value of empty string indicates no account code input."
DEFVAL { "" }
::= { cvCallActiveEntry 16 }
cvCallActiveERLLevelRev1 OBJECT-TYPE
SYNTAX Integer32 (-1..200)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object contains the current Echo Return Loss (ERL)
level for the call leg.
The value -1 indicates the level can not be determined or
level detection is disabled.
"
::= { cvCallActiveEntry 17 }
cvVoIPCallActiveTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvVoIPCallActiveEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is the VoIP extension to the call active table of
IETF Dial Control MIB. It contains VoIP call leg
information about specific VoIP call destination and the
selected QoS for the call leg.
"
::= { cvGatewayCallActive 2 }
cvVoIPCallActiveEntry OBJECT-TYPE
SYNTAX CvVoIPCallActiveEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The information regarding a single VoIP call leg.
The call leg entry is identified by using the same index
objects that are used by Call Active table of IETF Dial
Control MIB to identify the call.
An entry of this table is created when its associated call
active entry in the IETF Dial Control MIB is created and
the call active entry contains information for the call
establishment to the peer on the IP backbone via a voice
over IP peer.
The entry is deleted when its associated call active entry
in the IETF Dial Control MIB is deleted.
"
INDEX { callActiveSetupTime, callActiveIndex }
::= { cvVoIPCallActiveTable 1 }
CvVoIPCallActiveEntry ::=
SEQUENCE {
cvVoIPCallActiveConnectionId CvcGUid,
cvVoIPCallActiveRemoteIPAddress IpAddress,
cvVoIPCallActiveRemoteUDPPort INTEGER,
cvVoIPCallActiveRoundTripDelay Gauge32,
cvVoIPCallActiveSelectedQoS QosService,
cvVoIPCallActiveSessionProtocol CvSessionProtocol,
cvVoIPCallActiveSessionTarget DisplayString,
cvVoIPCallActiveOnTimeRvPlayout AbsoluteCounter32,
cvVoIPCallActiveGapFillWithSilence AbsoluteCounter32,
cvVoIPCallActiveGapFillWithPrediction AbsoluteCounter32,
cvVoIPCallActiveGapFillWithInterpolation AbsoluteCounter32,
cvVoIPCallActiveGapFillWithRedundancy AbsoluteCounter32,
cvVoIPCallActiveHiWaterPlayoutDelay AbsoluteCounter32,
cvVoIPCallActiveLoWaterPlayoutDelay Gauge32,
cvVoIPCallActiveReceiveDelay Gauge32,
cvVoIPCallActiveVADEnable TruthValue,
cvVoIPCallActiveCoderTypeRate CvcCoderTypeRate,
cvVoIPCallActiveLostPackets AbsoluteCounter32,
cvVoIPCallActiveLatePackets AbsoluteCounter32,
cvVoIPCallActiveEarlyPackets AbsoluteCounter32,
cvVoIPCallActiveUsername SnmpAdminString,
cvVoIPCallActiveProtocolCallId OCTET STRING,
cvVoIPCallActiveRemSigIPAddrT InetAddressType,
cvVoIPCallActiveRemSigIPAddr InetAddress,
cvVoIPCallActiveRemSigPort INTEGER,
cvVoIPCallActiveRemMediaIPAddrT InetAddressType,
cvVoIPCallActiveRemMediaIPAddr InetAddress,
cvVoIPCallActiveRemMediaPort INTEGER,
cvVoIPCallActiveSRTPEnable TruthValue
}
cvVoIPCallActiveConnectionId OBJECT-TYPE
SYNTAX CvcGUid
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The global call identifier for the gateway call."
::= { cvVoIPCallActiveEntry 1 }
cvVoIPCallActiveRemoteIPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated DESCRIPTION
"Remote system IP address for the VoIP call.
"
::= { cvVoIPCallActiveEntry 2 }
cvVoIPCallActiveRemoteUDPPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS deprecated DESCRIPTION
"Remote system UDP listener port to which to transmit voice
packets.
"
::= { cvVoIPCallActiveEntry 3 }
cvVoIPCallActiveRoundTripDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The voice packet round trip delay between local and
the remote system on the IP backbone during the call.
"
::= { cvVoIPCallActiveEntry 4 }
cvVoIPCallActiveSelectedQoS OBJECT-TYPE
SYNTAX QosService
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The selected RSVP QoS for the voice call."
::= { cvVoIPCallActiveEntry 5 }
cvVoIPCallActiveSessionProtocol OBJECT-TYPE
SYNTAX CvSessionProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object specifies the session protocol to be used
for Internet call between local and remote router via
IP backbone.
"
::= { cvVoIPCallActiveEntry 6 }
cvVoIPCallActiveSessionTarget OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object specifies the session target of the peer that
is used for the call. This object is set with the
information in the call associated
cvVoIPPeerCfgSessionTarget object when the voice over IP
call is connected.
"
::= { cvVoIPCallActiveEntry 7 }
cvVoIPCallActiveOnTimeRvPlayout OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice playout from data received on time for
this call. This plus the durations for the GapFills in the
following entries gives the Total Voice Playout Duration
for Active Voice.
This does not include duration for which no data was sent by the
Transmit end as voice signal, e.g., silence suppression
and fax signal. The On Time Playout Rate can be computed
by dividing this entry by the Total Voice Playout Duration.
This counter object will lock at the maximum value which
is approximately two days.
"
::= { cvVoIPCallActiveEntry 8 }
cvVoIPCallActiveGapFillWithSilence OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal replaced with signal played out
during silence due to voice data not received on time
(or lost) from voice gateway this call. This counter
object will lock at the maximum value which is
approximately two days.
"
::= { cvVoIPCallActiveEntry 9 }
cvVoIPCallActiveGapFillWithPrediction OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal played out with signal synthesized
from parameters or samples of data preceding in time due
to voice data not received on time (or lost) from voice
gateway for this call. An example of such playout is
frame-erasure or frame-concealment strategies in G.729 and
G.723.1 compression algorithms. This counter object will
lock at the maximum value which is approximately two days.
"
::= { cvVoIPCallActiveEntry 10 }
cvVoIPCallActiveGapFillWithInterpolation OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal played out with signal synthesized
from parameters or samples of data preceding and following
in time due to voice data not received on time (or lost)
from voice gateway for this call. This counter object
will lock at the maximum value which is approximately two
days.
"
::= { cvVoIPCallActiveEntry 11 }
cvVoIPCallActiveGapFillWithRedundancy OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal played out with signal synthesized
from redundancy parameters available due to voice data not
received on time (or lost) from voice gateway for this call.
This counter object will lock at the maximum value which
is approximately two days.
"
::= { cvVoIPCallActiveEntry 12 }
cvVoIPCallActiveHiWaterPlayoutDelay OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The high water mark Voice Playout FIFO Delay during
the voice call. This counter object will lock at the
maximum value which is approximately two days."
::= { cvVoIPCallActiveEntry 13 }
cvVoIPCallActiveLoWaterPlayoutDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The low water mark Voice Playout FIFO Delay during
the voice call."
::= { cvVoIPCallActiveEntry 14 }
cvVoIPCallActiveReceiveDelay OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average Playout FIFO Delay plus the decoder delay
during the voice call."
::= { cvVoIPCallActiveEntry 15 }
cvVoIPCallActiveVADEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The object indicates whether or not the VAD (Voice Activity
Detection) was enabled for the voice call."
::= { cvVoIPCallActiveEntry 16 }
cvVoIPCallActiveCoderTypeRate OBJECT-TYPE
SYNTAX CvcCoderTypeRate
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The negotiated coder rate. It specifies the transmit rate of
voice/fax compression to its associated call leg for the
call. This rate is different from the configuration rate
because of rate negotiation during the call.
"
::= { cvVoIPCallActiveEntry 17 }
cvVoIPCallActiveLostPackets OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of lost voice packets during the call.
"
::= { cvVoIPCallActiveEntry 18 }
cvVoIPCallActiveEarlyPackets OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of received voice packets that
arrived too early to store in jitter buffer
during the call.
"
::= { cvVoIPCallActiveEntry 19 }
cvVoIPCallActiveLatePackets OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of received voice packets that
arrived too late to playout with CODEC (Coder/Decoder)
during the call.
"
::= { cvVoIPCallActiveEntry 20 }
cvVoIPCallActiveUsername OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual identifier of the calling party (user) of the
call. If the username is not available, then the value of
this object will have a length of zero."
::= { cvVoIPCallActiveEntry 21 }
cvVoIPCallActiveProtocolCallId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocol-specific call identifier for the VoIP call."
::= { cvVoIPCallActiveEntry 22 }
cvVoIPCallActiveRemSigIPAddrT OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of address contained in
the associated instance of cvVoIPCallActiveRemSigIPAddr."
::= { cvVoIPCallActiveEntry 23 }
cvVoIPCallActiveRemSigIPAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote signalling IP address for the VoIP call."
::= { cvVoIPCallActiveEntry 24 }
cvVoIPCallActiveRemSigPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote signalling listener port to which to transmit
voice packets."
::= { cvVoIPCallActiveEntry 25 }
cvVoIPCallActiveRemMediaIPAddrT OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of address contained in
the associated instance of
cvVoIPCallActiveRemMediaIPAddr."
::= { cvVoIPCallActiveEntry 26 }
cvVoIPCallActiveRemMediaIPAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote media end point IP address for the VoIP call."
::= { cvVoIPCallActiveEntry 27 }
cvVoIPCallActiveRemMediaPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote media end point listener port to which to transmit
voice packets."
::= { cvVoIPCallActiveEntry 28 }
cvVoIPCallActiveSRTPEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object indicates whether or not the SRTP (Secured RTP)
was enabled for the voice call."
::= { cvVoIPCallActiveEntry 29 }
cvCallHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvCallHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is the voice extension to the call history table
of IETF Dial Control MIB. It contains voice encapsulation
call leg information such as voice packet statistics,
coder usage and end to end bandwidth of the call leg.
"
::= { cvGatewayCallHistory 1 }
cvCallHistoryEntry OBJECT-TYPE
SYNTAX CvCallHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The information regarding a single voice encapsulation
call leg.
The call leg entry is identified by using the same index
objects that are used by Call Active table of IETF Dial
Control MIB to identify the call.
An entry of this table is created when its associated call
history entry in the IETF Dial Control MIB is created and
the call history entry contains the call establishment to
a voice encapsulation peer.
The entry is deleted when its associated call active entry
in the IETF Dial Control MIB is deleted.
"
INDEX { cCallHistoryIndex }
::= { cvCallHistoryTable 1 }
CvCallHistoryEntry ::=
SEQUENCE {
cvCallHistoryConnectionId CvcGUid,
cvCallHistoryTxDuration AbsoluteCounter32,
cvCallHistoryVoiceTxDuration AbsoluteCounter32,
cvCallHistoryFaxTxDuration AbsoluteCounter32,
cvCallHistoryCoderTypeRate CvcCoderTypeRate,
cvCallHistoryNoiseLevel Integer32,
cvCallHistoryACOMLevel Integer32,
cvCallHistorySessionTarget DisplayString,
cvCallHistoryImgPageCount AbsoluteCounter32,
cvCallHistoryCallingName SnmpAdminString,
cvCallHistoryCallerIDBlock TruthValue,
cvCallHistoryAccountCode SnmpAdminString
}
cvCallHistoryConnectionId OBJECT-TYPE
SYNTAX CvcGUid
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The global call identifier for the gateway call."
::= { cvCallHistoryEntry 1 }
cvCallHistoryTxDuration OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of Transmit path open from this peer to the
voice gateway for the call leg. This counter object will
lock at the maximum value which is approximately two
days.
"
::= { cvCallHistoryEntry 2 }
cvCallHistoryVoiceTxDuration OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration for this call leg. The Voice Utilization Rate
can be obtained by dividing this by
cvCallHistoryTXDuration object. This counter object will
lock at the maximum value which is approximately two
days.
"
::= { cvCallHistoryEntry 3 }
cvCallHistoryFaxTxDuration OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of fax transmitted from this peer to voice
gateway for this call leg. The FAX Utilization Rate can be
obtained by dividing this by cvCallHistoryTXDuration
object. This counter object will lock at the maximum
value which is approximately two days.
"
::= { cvCallHistoryEntry 4 }
cvCallHistoryCoderTypeRate OBJECT-TYPE
SYNTAX CvcCoderTypeRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The negotiated coder rate. It specifies the transmit rate
of voice/fax compression to its associated call leg for
the call.
"
::= { cvCallHistoryEntry 5 }
cvCallHistoryNoiseLevel OBJECT-TYPE
SYNTAX Integer32 (-128..8)
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object contains the average noise level for the call
leg.
"
::= { cvCallHistoryEntry 6 }
cvCallHistoryACOMLevel OBJECT-TYPE
SYNTAX Integer32 (-1..127)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object contains the average ACOM level for the call
leg. The value -1 indicates the level can not be
determined or level detection is disabled.
"
::= { cvCallHistoryEntry 7 }
cvCallHistorySessionTarget OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object specifies the session target of the peer that
is used for the call leg via telephony interface.
"
::= { cvCallHistoryEntry 8 }
cvCallHistoryImgPageCount OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "pages"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of FAX related image pages are received or
transmitted via the peer for the call leg.
"
::= { cvCallHistoryEntry 9 }
cvCallHistoryCallingName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The calling party name of the call. If the name is
not available, then it will have a length of zero."
::= { cvCallHistoryEntry 10 }
cvCallHistoryCallerIDBlock OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object indicates whether or not the caller ID feature
is blocked for this call."
::= { cvCallHistoryEntry 11 }
cvCallHistoryAccountCode OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..50))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object indicates the account code input to the call.
It could be used by down stream billing server.
The value of empty string indicates no account code input."
DEFVAL { "" }
::= { cvCallHistoryEntry 12 }
cvVoIPCallHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvVoIPCallHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is the VoIP extension to the call history table
of IETF Dial Control MIB. It contains VoIP call leg
information about specific VoIP call destination and the
selected QoS for the call leg.
"
::= { cvGatewayCallHistory 2 }
cvVoIPCallHistoryEntry OBJECT-TYPE
SYNTAX CvVoIPCallHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The information regarding a single VoIP call leg.
The call leg entry is identified by using the same index
objects that are used by Call Active table of IETF Dial
Control MIB to identify the call.
An entry of this table is created when its associated call
history entry in the IETF Dial Control MIB is created and
the call history entry contains information for the call
establishment to the peer on the IP backbone via a voice
over IP peer.
The entry is deleted when its associated call history
entry in the IETF Dial Control MIB is deleted.
"
INDEX { cCallHistoryIndex }
::= { cvVoIPCallHistoryTable 1 }
CvVoIPCallHistoryEntry ::=
SEQUENCE {
cvVoIPCallHistoryConnectionId CvcGUid,
cvVoIPCallHistoryRemoteIPAddress IpAddress,
cvVoIPCallHistoryRemoteUDPPort INTEGER,
cvVoIPCallHistoryRoundTripDelay Gauge32,
cvVoIPCallHistorySelectedQoS QosService,
cvVoIPCallHistorySessionProtocol CvSessionProtocol,
cvVoIPCallHistorySessionTarget DisplayString,
cvVoIPCallHistoryOnTimeRvPlayout AbsoluteCounter32,
cvVoIPCallHistoryGapFillWithSilence AbsoluteCounter32,
cvVoIPCallHistoryGapFillWithPrediction AbsoluteCounter32,
cvVoIPCallHistoryGapFillWithInterpolation AbsoluteCounter32,
cvVoIPCallHistoryGapFillWithRedundancy AbsoluteCounter32,
cvVoIPCallHistoryHiWaterPlayoutDelay AbsoluteCounter32,
cvVoIPCallHistoryLoWaterPlayoutDelay Gauge32,
cvVoIPCallHistoryReceiveDelay Gauge32,
cvVoIPCallHistoryVADEnable TruthValue,
cvVoIPCallHistoryCoderTypeRate CvcCoderTypeRate,
cvVoIPCallHistoryIcpif Integer32,
cvVoIPCallHistoryLostPackets AbsoluteCounter32,
cvVoIPCallHistoryLatePackets AbsoluteCounter32,
cvVoIPCallHistoryEarlyPackets AbsoluteCounter32,
cvVoIPCallHistoryUsername SnmpAdminString,
cvVoIPCallHistoryProtocolCallId OCTET STRING,
cvVoIPCallHistoryRemSigIPAddrT InetAddressType,
cvVoIPCallHistoryRemSigIPAddr InetAddress,
cvVoIPCallHistoryRemSigPort INTEGER,
cvVoIPCallHistoryRemMediaIPAddrT InetAddressType,
cvVoIPCallHistoryRemMediaIPAddr InetAddress,
cvVoIPCallHistoryRemMediaPort INTEGER,
cvVoIPCallHistorySRTPEnable TruthValue
}
cvVoIPCallHistoryConnectionId OBJECT-TYPE
SYNTAX CvcGUid
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The global call identifier for the gateway call."
::= { cvVoIPCallHistoryEntry 1 }
cvVoIPCallHistoryRemoteIPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated DESCRIPTION
"Remote system IP address for the call.
"
::= { cvVoIPCallHistoryEntry 2 }
cvVoIPCallHistoryRemoteUDPPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS deprecated DESCRIPTION
"Remote system UDP listener port to which to transmit voice
packets for the call.
"
::= { cvVoIPCallHistoryEntry 3 }
cvVoIPCallHistoryRoundTripDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The voice packet round trip delay between local and
the remote system on the IP backbone during the call.
"
::= { cvVoIPCallHistoryEntry 4 }
cvVoIPCallHistorySelectedQoS OBJECT-TYPE
SYNTAX QosService
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The selected RSVP QoS for the call."
::= { cvVoIPCallHistoryEntry 5 }
cvVoIPCallHistorySessionProtocol OBJECT-TYPE
SYNTAX CvSessionProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object specifies the session protocol to be used
for Internet call between local and remote router via
IP backbone.
"
::= { cvVoIPCallHistoryEntry 6 }
cvVoIPCallHistorySessionTarget OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object specifies the session target of the peer that
is used for the Voice over IP call.
"
::= { cvVoIPCallHistoryEntry 7 }
cvVoIPCallHistoryOnTimeRvPlayout OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice playout from data received on time for
this call. This plus the durations for the GapFills in the
following entries gives the Total Voice Playout Duration
for Active Voice.
This does not include duration for which no data was sent by the
Transmit end as voice signal, e.g., silence suppression
and fax signal. The On Time Playout Rate can be computed
by dividing this entry by the Total Voice Playout Duration.
This counter object will lock at the maximum value which
is approximately two days.
"
::= { cvVoIPCallHistoryEntry 8 }
cvVoIPCallHistoryGapFillWithSilence OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal replaced with signal played out
during silence due to voice data not received on time
(or lost) from voice gateway this call. This counter
object will lock at the maximum value which is
approximately two days.
"
::= { cvVoIPCallHistoryEntry 9 }
cvVoIPCallHistoryGapFillWithPrediction OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal played out with signal synthesized
from parameters or samples of data preceding in time due to
voice data not received on time (or lost) from voice gateway
for this call. An example of such playout is frame-erasure
or frame-concealment strategies in G.729 and G.723.1
compression algorithms. This counter object will lock at
the maximum value which is approximately two days.
"
::= { cvVoIPCallHistoryEntry 10 }
cvVoIPCallHistoryGapFillWithInterpolation OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal played out with signal synthesized
from parameters or samples of data preceding and following
in time due to voice data not received on time (or lost)
from voice gateway for this call. This counter object
will lock at the maximum value which is approximately two
days.
"
::= { cvVoIPCallHistoryEntry 11 }
cvVoIPCallHistoryGapFillWithRedundancy OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Duration of voice signal played out with signal synthesized
from redundancy parameters available due to voice data not
received on time (or lost) from voice gateway for this call.
This counter object will lock at the maximum value which
is approximately two days.
"
::= { cvVoIPCallHistoryEntry 12 }
cvVoIPCallHistoryHiWaterPlayoutDelay OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The high water mark Voice Playout FIFO Delay during
the voice call. This counter object will lock at the
maximum value which is approximately two days."
::= { cvVoIPCallHistoryEntry 13 }
cvVoIPCallHistoryLoWaterPlayoutDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The low water mark Voice Playout FIFO Delay during
the voice call."
::= { cvVoIPCallHistoryEntry 14 }
cvVoIPCallHistoryReceiveDelay OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average Playout FIFO Delay plus the decoder delay
during the voice call."
::= { cvVoIPCallHistoryEntry 15 }
cvVoIPCallHistoryVADEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The object indicates whether or not the VAD (Voice Activity
Detection) was enabled for the voice call."
::= { cvVoIPCallHistoryEntry 16 }
cvVoIPCallHistoryCoderTypeRate OBJECT-TYPE
SYNTAX CvcCoderTypeRate
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The negotiated coder rate. It specifies the transmit rate of
voice/fax compression to its associated call leg for the
call. This rate is different from the configuration rate
because of rate negotiation during the call.
"
::= { cvVoIPCallHistoryEntry 17 }
cvVoIPCallHistoryIcpif OBJECT-TYPE
SYNTAX Integer32 (-1..55)
UNITS "equipment impairment factor (eif)"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Calculated Planning Impairment Factor (Icpif) of the
call that is associated to this call leg.
The value in this object is computed by the following
equation.
Icpif of the call =
Itotal (total impairment value) of the call - A
(Expectation Factor) in the cvVoIPPeerCfgExpectFactor of
the call leg associated peer.
A value of -1 implies that Icpif was not calculated and is
meaningless for this call.
"
REFERENCE
"[1] ITU G.113: Section 7.2 Impairment factors and the total
impairment value.
[2] ITU G.113: Sections 9 Considerations associated with
the Calculated Planning Impairment Factor (Icpif).
"
::= { cvVoIPCallHistoryEntry 18 }
cvVoIPCallHistoryLostPackets OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of lost voice packets during the call.
"
::= { cvVoIPCallHistoryEntry 19 }
cvVoIPCallHistoryEarlyPackets OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of received voice packets that are
arrived too early to store in jitter buffer
during the call.
"
::= { cvVoIPCallHistoryEntry 20 }
cvVoIPCallHistoryLatePackets OBJECT-TYPE
SYNTAX AbsoluteCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of received voice packets that are
arrived too late to playout with CODEC (Coder/Decoder)
during the call.
"
::= { cvVoIPCallHistoryEntry 21 }
cvVoIPCallHistoryUsername OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual identifier of the calling party (user) of the
call. If the username is not available, then the value of
this object will have a length of zero."
::= { cvVoIPCallHistoryEntry 22 }
cvVoIPCallHistoryProtocolCallId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocol-specific call identifier for the VoIP call."
::= { cvVoIPCallHistoryEntry 23 }
cvVoIPCallHistoryRemSigIPAddrT OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of address contained in
the associated instance of cvVoIPCallHistoryRemSigIPAddr."
::= { cvVoIPCallHistoryEntry 24 }
cvVoIPCallHistoryRemSigIPAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote signalling IP address for the VoIP call."
::= { cvVoIPCallHistoryEntry 25 }
cvVoIPCallHistoryRemSigPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote signalling listener port to which to transmit
voice packets."
::= { cvVoIPCallHistoryEntry 26 }
cvVoIPCallHistoryRemMediaIPAddrT OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of address contained in
the associated instance of
cvVoIPCallHistoryRemMediaIPAddr."
::= { cvVoIPCallHistoryEntry 27 }
cvVoIPCallHistoryRemMediaIPAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote media end point IP address for the VoIP call."
::= { cvVoIPCallHistoryEntry 28 }
cvVoIPCallHistoryRemMediaPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote media end point listener port to which to transmit
voice packets."
::= { cvVoIPCallHistoryEntry 29 }
cvVoIPCallHistorySRTPEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object indicates whether or not the SRTP (Secured RTP)
was enabled for the voice call."
::= { cvVoIPCallHistoryEntry 30 }
cvdcMIBNotificationPrefix OBJECT IDENTIFIER ::=
{ ciscoVoiceDialControlMIB 2 }
cvdcMIBNotifications OBJECT IDENTIFIER ::=
{ cvdcMIBNotificationPrefix 0 }
cvdcPoorQoVNotification NOTIFICATION-TYPE
OBJECTS {
cvVoIPCallHistoryConnectionId,
cvVoIPCallHistoryIcpif,
cvVoIPCallHistoryRemoteIPAddress,
cCallHistoryCallOrigin,
cvCommonDcCallHistoryCoderTypeRate
}
STATUS deprecated DESCRIPTION
"Poor quality of voice notification. A
cvdcPoorQoVNotification is sent at the call disconnection
time if the value of cvVoIPCallHistoryIcpif exceeds the
value of cvVoIPPeerCfgIcpif in the call associated peer.
"
::= { cvdcMIBNotifications 1 }
cvdcPoorQoVNotificationRev1 NOTIFICATION-TYPE
OBJECTS {
cvVoIPCallHistoryConnectionId,
cvVoIPCallHistoryIcpif,
cvVoIPCallHistoryRemMediaIPAddrT,
cvVoIPCallHistoryRemMediaIPAddr,
cCallHistoryCallOrigin,
cvCommonDcCallHistoryCoderTypeRate
}
STATUS current
DESCRIPTION
"Poor quality of voice notification. A
cvdcPoorQoVNotificationRev1 is sent at the call
disconnection time if the value of cvVoIPCallHistoryIcpif
exceeds the value of cvVoIPPeerCfgIcpif in the call
associated peer."
::= { cvdcMIBNotifications 2 }
cvdcMIBConformance OBJECT IDENTIFIER ::=
{ ciscoVoiceDialControlMIB 3 }
cvdcMIBCompliances OBJECT IDENTIFIER ::=
{ cvdcMIBConformance 1 }
cvdcMIBGroups OBJECT IDENTIFIER ::=
{ cvdcMIBConformance 2 }
cvdcMIBCompliance MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroup }
GROUP cvdcVoiceCfgGroup
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroup
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroup
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroup
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 1 }
cvdcMIBComplianceRev1 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev1 }
GROUP cvdcVoiceCfgGroupRev1
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroup
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroup
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev1
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 2 }
cvdcMIBComplianceRev2 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev2 }
GROUP cvdcVoiceCfgGroupRev1
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev1
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev1
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev1
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 3 }
cvdcMIBComplianceRev3 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev3 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev2
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev1
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev3
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 4 }
cvdcMIBComplianceRev4 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev4 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev2
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev1
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev3
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 5 }
cvdcMIBComplianceRev5 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev3 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev2
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev2
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev3
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 6 }
cvdcMIBComplianceRev6 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev3 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev2
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev2
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev4
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 7 }
cvdcMIBComplianceRev7 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev4 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev2
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev2
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev4
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 8 }
cvdcMIBComplianceRev8 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev5 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev3
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev2
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev4
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 9 }
cvdcMIBComplianceRev9 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev5 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev4
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev3
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev4
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 10 }
cvdcMIBComplianceRev10 MODULE-COMPLIANCE
STATUS deprecated DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev5 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev4
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev4
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev4
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 11 }
cvdcMIBComplianceRev11 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which
implement the CISCO VOICE DIAL CONTROL MIB"
MODULE MANDATORY-GROUPS
{ cvdcGeneralCfgGroupRev5 }
GROUP cvdcVoiceCfgGroupRev2
DESCRIPTION
"This group is mandatory for voice dial control
configuration which is related to GSTN(General Switched
Telephony Network).
GSTN encompasses analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
GROUP cvdcVoIPCfgGroupRev4
DESCRIPTION
"This group is mandatory for VoIP dial control configuration
which is related to transmit voice packet via IP network.
"
GROUP cvCallGroupRev4
DESCRIPTION
"This group is mandatory for all voice related active call
and call history via GSTN.
"
GROUP cvVoIPCallGroupRev5
DESCRIPTION
"This group is mandatory for all VoIP related active call
and call history via IP network.
"
::= { cvdcMIBCompliances 12 }
cvdcGeneralCfgGroup OBJECT-GROUP
OBJECTS {
cvGeneralPoorQoVNotificationEnable,
cvPeerCfgIfIndex,
cvPeerCfgType,
cvPeerCfgRowStatus
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the general
Voice Gateway Call Dial Control configuration capability."
::= { cvdcMIBGroups 1 }
cvdcVoiceCfgGroup OBJECT-GROUP
OBJECTS {
cvVoicePeerCfgSessionTarget,
cvVoicePeerCfgDialDigitsPrefix
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Dial Control configuration
capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 2 }
cvdcVoIPCfgGroup OBJECT-GROUP
OBJECTS {
cvVoIPPeerCfgSessionProtocol,
cvVoIPPeerCfgSessionTarget,
cvVoIPPeerCfgCoderRate,
cvVoIPPeerCfgFaxRate,
cvVoIPPeerCfgDesiredQoS,
cvVoIPPeerCfgMinAcceptableQoS,
cvVoIPPeerCfgVADEnable,
cvVoIPPeerCfgExpectFactor,
cvVoIPPeerCfgIcpif,
cvVoIPPeerCfgPoorQoVNotificationEnable,
cvVoIPPeerCfgUDPChecksumEnable,
cvVoIPPeerCfgIPPrecedence
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Dial Control
configuration capability.
"
::= { cvdcMIBGroups 3 }
cvCallGroup OBJECT-GROUP
OBJECTS {
cvCallActiveConnectionId,
cvCallActiveTxDuration,
cvCallActiveVoiceTxDuration,
cvCallActiveFaxTxDuration,
cvCallActiveCoderTypeRate,
cvCallActiveNoiseLevel,
cvCallActiveACOMLevel,
cvCallActiveOutSignalLevel,
cvCallActiveInSignalLevel,
cvCallActiveERLLevel,
cvCallActiveSessionTarget,
cvCallHistoryConnectionId,
cvCallHistoryTxDuration,
cvCallHistoryVoiceTxDuration,
cvCallHistoryFaxTxDuration,
cvCallHistoryCoderTypeRate,
cvCallHistoryNoiseLevel,
cvCallHistoryACOMLevel,
cvCallHistorySessionTarget
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Call capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 4 }
cvVoIPCallGroup OBJECT-GROUP
OBJECTS {
cvVoIPCallActiveConnectionId,
cvVoIPCallActiveRemoteIPAddress,
cvVoIPCallActiveRemoteUDPPort,
cvVoIPCallActiveRoundTripDelay,
cvVoIPCallActiveSelectedQoS,
cvVoIPCallActiveSessionProtocol,
cvVoIPCallActiveSessionTarget,
cvVoIPCallActiveOnTimeRvPlayout,
cvVoIPCallActiveGapFillWithSilence,
cvVoIPCallActiveGapFillWithPrediction,
cvVoIPCallActiveGapFillWithInterpolation,
cvVoIPCallActiveGapFillWithRedundancy,
cvVoIPCallActiveHiWaterPlayoutDelay,
cvVoIPCallActiveLoWaterPlayoutDelay,
cvVoIPCallActiveReceiveDelay,
cvVoIPCallActiveVADEnable,
cvVoIPCallActiveCoderTypeRate,
cvVoIPCallHistoryConnectionId,
cvVoIPCallHistoryRemoteIPAddress,
cvVoIPCallHistoryRemoteUDPPort,
cvVoIPCallHistoryRoundTripDelay,
cvVoIPCallHistorySelectedQoS,
cvVoIPCallHistorySessionProtocol,
cvVoIPCallHistorySessionTarget,
cvVoIPCallHistoryOnTimeRvPlayout,
cvVoIPCallHistoryGapFillWithSilence,
cvVoIPCallHistoryGapFillWithPrediction,
cvVoIPCallHistoryGapFillWithInterpolation,
cvVoIPCallHistoryGapFillWithRedundancy,
cvVoIPCallHistoryHiWaterPlayoutDelay,
cvVoIPCallHistoryLoWaterPlayoutDelay,
cvVoIPCallHistoryReceiveDelay,
cvVoIPCallHistoryVADEnable,
cvVoIPCallHistoryCoderTypeRate,
cvVoIPCallHistoryIcpif
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Call
capability."
::= { cvdcMIBGroups 5 }
cvdcGeneralCfgGroupRev1 OBJECT-GROUP
OBJECTS {
cvGeneralPoorQoVNotificationEnable,
cvPeerCfgIfIndex,
cvPeerCfgType,
cvPeerCfgRowStatus,
cvPeerCommonCfgIncomingDnisDigits,
cvPeerCommonCfgMaxConnections,
cvPeerCommonCfgApplicationName
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the general
Voice Gateway Call Dial Control configuration capability."
::= { cvdcMIBGroups 6 }
cvdcVoiceCfgGroupRev1 OBJECT-GROUP
OBJECTS {
cvVoicePeerCfgSessionTarget,
cvVoicePeerCfgDialDigitsPrefix,
cvVoicePeerCfgDIDCallEnable,
cvVoicePeerCfgCasGroup
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Dial Control configuration
capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 7 }
cvVoIPCallGroupRev1 OBJECT-GROUP
OBJECTS {
cvVoIPCallActiveConnectionId,
cvVoIPCallActiveRemoteIPAddress,
cvVoIPCallActiveRemoteUDPPort,
cvVoIPCallActiveRoundTripDelay,
cvVoIPCallActiveSelectedQoS,
cvVoIPCallActiveSessionProtocol,
cvVoIPCallActiveSessionTarget,
cvVoIPCallActiveOnTimeRvPlayout,
cvVoIPCallActiveGapFillWithSilence,
cvVoIPCallActiveGapFillWithPrediction,
cvVoIPCallActiveGapFillWithInterpolation,
cvVoIPCallActiveGapFillWithRedundancy,
cvVoIPCallActiveHiWaterPlayoutDelay,
cvVoIPCallActiveLoWaterPlayoutDelay,
cvVoIPCallActiveReceiveDelay,
cvVoIPCallActiveVADEnable,
cvVoIPCallActiveCoderTypeRate,
cvVoIPCallActiveLostPackets,
cvVoIPCallActiveLatePackets,
cvVoIPCallActiveEarlyPackets,
cvVoIPCallHistoryConnectionId,
cvVoIPCallHistoryRemoteIPAddress,
cvVoIPCallHistoryRemoteUDPPort,
cvVoIPCallHistoryRoundTripDelay,
cvVoIPCallHistorySelectedQoS,
cvVoIPCallHistorySessionProtocol,
cvVoIPCallHistorySessionTarget,
cvVoIPCallHistoryOnTimeRvPlayout,
cvVoIPCallHistoryGapFillWithSilence,
cvVoIPCallHistoryGapFillWithPrediction,
cvVoIPCallHistoryGapFillWithInterpolation,
cvVoIPCallHistoryGapFillWithRedundancy,
cvVoIPCallHistoryHiWaterPlayoutDelay,
cvVoIPCallHistoryLoWaterPlayoutDelay,
cvVoIPCallHistoryReceiveDelay,
cvVoIPCallHistoryVADEnable,
cvVoIPCallHistoryCoderTypeRate,
cvVoIPCallHistoryIcpif,
cvVoIPCallHistoryLostPackets,
cvVoIPCallHistoryLatePackets,
cvVoIPCallHistoryEarlyPackets
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Call
capability."
::= { cvdcMIBGroups 8 }
cvCallGroupRev1 OBJECT-GROUP
OBJECTS {
cvCallActiveConnectionId,
cvCallActiveTxDuration,
cvCallActiveVoiceTxDuration,
cvCallActiveFaxTxDuration,
cvCallActiveCoderTypeRate,
cvCallActiveNoiseLevel,
cvCallActiveACOMLevel,
cvCallActiveOutSignalLevel,
cvCallActiveInSignalLevel,
cvCallActiveERLLevel,
cvCallActiveSessionTarget,
cvCallActiveImgPageCount,
cvCallHistoryConnectionId,
cvCallHistoryTxDuration,
cvCallHistoryVoiceTxDuration,
cvCallHistoryFaxTxDuration,
cvCallHistoryCoderTypeRate,
cvCallHistoryNoiseLevel,
cvCallHistoryACOMLevel,
cvCallHistorySessionTarget,
cvCallHistoryImgPageCount
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Dial Control configuration
capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 9 }
cvdcGeneralCfgGroupRev2 OBJECT-GROUP
OBJECTS {
cvGeneralPoorQoVNotificationEnable,
cvPeerCfgIfIndex,
cvPeerCfgType,
cvPeerCfgRowStatus,
cvPeerCommonCfgIncomingDnisDigits,
cvPeerCommonCfgMaxConnections,
cvPeerCommonCfgApplicationName,
cvPeerCommonCfgPreference
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the general
Voice Gateway Call Dial Control configuration capability."
::= { cvdcMIBGroups 10 }
cvdcVoIPCfgGroupRev1 OBJECT-GROUP
OBJECTS {
cvVoIPPeerCfgSessionProtocol,
cvVoIPPeerCfgSessionTarget,
cvVoIPPeerCfgCoderRate,
cvVoIPPeerCfgFaxRate,
cvVoIPPeerCfgDesiredQoS,
cvVoIPPeerCfgMinAcceptableQoS,
cvVoIPPeerCfgVADEnable,
cvVoIPPeerCfgExpectFactor,
cvVoIPPeerCfgIcpif,
cvVoIPPeerCfgPoorQoVNotificationEnable,
cvVoIPPeerCfgUDPChecksumEnable,
cvVoIPPeerCfgIPPrecedence,
cvVoIPPeerCfgTechPrefix,
cvVoIPPeerCfgDigitRelay
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Dial Control
configuration capability.
"
::= { cvdcMIBGroups 11 }
cvdcGeneralCfgGroupRev3 OBJECT-GROUP
OBJECTS {
cvGeneralPoorQoVNotificationEnable,
cvPeerCfgIfIndex,
cvPeerCfgType,
cvPeerCfgRowStatus,
cvPeerCommonCfgIncomingDnisDigits,
cvPeerCommonCfgMaxConnections,
cvPeerCommonCfgApplicationName,
cvPeerCommonCfgPreference,
cvPeerCommonCfgHuntStop
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the general
Voice Gateway Call Dial Control configuration capability."
::= { cvdcMIBGroups 12 }
cvdcVoiceCfgGroupRev2 OBJECT-GROUP
OBJECTS {
cvVoicePeerCfgSessionTarget,
cvVoicePeerCfgDialDigitsPrefix,
cvVoicePeerCfgDIDCallEnable,
cvVoicePeerCfgCasGroup,
cvVoicePeerCfgRegisterE164,
cvVoicePeerCfgForwardDigits,
cvVoicePeerCfgEchoCancellerTest
}
STATUS current
DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Dial Control configuration
capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 13 }
cvdcVoIPCfgGroupRev2 OBJECT-GROUP
OBJECTS {
cvVoIPPeerCfgSessionProtocol,
cvVoIPPeerCfgSessionTarget,
cvVoIPPeerCfgCoderRate,
cvVoIPPeerCfgFaxRate,
cvVoIPPeerCfgDesiredQoS,
cvVoIPPeerCfgMinAcceptableQoS,
cvVoIPPeerCfgVADEnable,
cvVoIPPeerCfgExpectFactor,
cvVoIPPeerCfgIcpif,
cvVoIPPeerCfgPoorQoVNotificationEnable,
cvVoIPPeerCfgUDPChecksumEnable,
cvVoIPPeerCfgIPPrecedence,
cvVoIPPeerCfgTechPrefix,
cvVoIPPeerCfgDigitRelay,
cvVoIPPeerCfgCoderBytes,
cvVoIPPeerCfgFaxBytes,
cvVoIPPeerCfgInBandSignaling
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Dial Control
configuration capability.
"
::= { cvdcMIBGroups 14 }
cvVoIPCallGroupRev3 OBJECT-GROUP
OBJECTS {
cvVoIPCallActiveConnectionId,
cvVoIPCallActiveRemoteIPAddress,
cvVoIPCallActiveRemoteUDPPort,
cvVoIPCallActiveRoundTripDelay,
cvVoIPCallActiveSelectedQoS,
cvVoIPCallActiveSessionProtocol,
cvVoIPCallActiveSessionTarget,
cvVoIPCallActiveOnTimeRvPlayout,
cvVoIPCallActiveGapFillWithSilence,
cvVoIPCallActiveGapFillWithPrediction,
cvVoIPCallActiveGapFillWithInterpolation,
cvVoIPCallActiveGapFillWithRedundancy,
cvVoIPCallActiveHiWaterPlayoutDelay,
cvVoIPCallActiveLoWaterPlayoutDelay,
cvVoIPCallActiveReceiveDelay,
cvVoIPCallActiveLostPackets,
cvVoIPCallActiveLatePackets,
cvVoIPCallActiveEarlyPackets,
cvVoIPCallHistoryConnectionId,
cvVoIPCallHistoryRemoteIPAddress,
cvVoIPCallHistoryRemoteUDPPort,
cvVoIPCallHistoryRoundTripDelay,
cvVoIPCallHistorySelectedQoS,
cvVoIPCallHistorySessionProtocol,
cvVoIPCallHistorySessionTarget,
cvVoIPCallHistoryOnTimeRvPlayout,
cvVoIPCallHistoryGapFillWithSilence,
cvVoIPCallHistoryGapFillWithPrediction,
cvVoIPCallHistoryGapFillWithInterpolation,
cvVoIPCallHistoryGapFillWithRedundancy,
cvVoIPCallHistoryHiWaterPlayoutDelay,
cvVoIPCallHistoryLoWaterPlayoutDelay,
cvVoIPCallHistoryReceiveDelay,
cvVoIPCallHistoryIcpif,
cvVoIPCallHistoryLostPackets,
cvVoIPCallHistoryLatePackets,
cvVoIPCallHistoryEarlyPackets
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Call
capability."
::= { cvdcMIBGroups 15 }
cvdcNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS{
cvdcPoorQoVNotification
}
STATUS deprecated DESCRIPTION
"The notifications for the CISCO-VOICE-DIAL-CONTROL-MIB"
::= { cvdcMIBGroups 16 }
cvCallGroupRev2 OBJECT-GROUP
OBJECTS {
cvCallActiveConnectionId,
cvCallActiveTxDuration,
cvCallActiveVoiceTxDuration,
cvCallActiveFaxTxDuration,
cvCallActiveCoderTypeRate,
cvCallActiveNoiseLevel,
cvCallActiveACOMLevel,
cvCallActiveOutSignalLevel,
cvCallActiveInSignalLevel,
cvCallActiveERLLevel,
cvCallActiveSessionTarget,
cvCallActiveImgPageCount,
cvCallActiveCallingName,
cvCallActiveCallerIDBlock,
cvCallActiveEcanReflectorLocation,
cvCallHistoryConnectionId,
cvCallHistoryTxDuration,
cvCallHistoryVoiceTxDuration,
cvCallHistoryFaxTxDuration,
cvCallHistoryCoderTypeRate,
cvCallHistoryNoiseLevel,
cvCallHistoryACOMLevel,
cvCallHistorySessionTarget,
cvCallHistoryImgPageCount,
cvCallHistoryCallingName,
cvCallHistoryCallerIDBlock
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Dial Control configuration
capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 17 }
cvdcGeneralCfgGroupRev4 OBJECT-GROUP
OBJECTS {
cvGeneralPoorQoVNotificationEnable,
cvPeerCfgIfIndex,
cvPeerCfgType,
cvPeerCfgRowStatus,
cvPeerCommonCfgIncomingDnisDigits,
cvPeerCommonCfgMaxConnections,
cvPeerCommonCfgApplicationName,
cvPeerCommonCfgPreference,
cvPeerCommonCfgHuntStop,
cvPeerCommonCfgDnisMappingName,
cvPeerCommonCfgSourceCarrierId,
cvPeerCommonCfgTargetCarrierId,
cvPeerCommonCfgSourceTrunkGrpLabel,
cvPeerCommonCfgTargetTrunkGrpLabel
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the general
Voice Gateway Call Dial Control configuration
capability."
::= { cvdcMIBGroups 18 }
cvVoIPCallGroupRev4 OBJECT-GROUP
OBJECTS {
cvVoIPCallActiveConnectionId,
cvVoIPCallActiveRoundTripDelay,
cvVoIPCallActiveSelectedQoS,
cvVoIPCallActiveSessionProtocol,
cvVoIPCallActiveSessionTarget,
cvVoIPCallActiveOnTimeRvPlayout,
cvVoIPCallActiveGapFillWithSilence,
cvVoIPCallActiveGapFillWithPrediction,
cvVoIPCallActiveGapFillWithInterpolation,
cvVoIPCallActiveGapFillWithRedundancy,
cvVoIPCallActiveHiWaterPlayoutDelay,
cvVoIPCallActiveLoWaterPlayoutDelay,
cvVoIPCallActiveReceiveDelay,
cvVoIPCallActiveLostPackets,
cvVoIPCallActiveLatePackets,
cvVoIPCallActiveEarlyPackets,
cvVoIPCallActiveUsername,
cvVoIPCallActiveProtocolCallId,
cvVoIPCallActiveRemSigIPAddrT,
cvVoIPCallActiveRemSigIPAddr,
cvVoIPCallActiveRemSigPort,
cvVoIPCallActiveRemMediaIPAddrT,
cvVoIPCallActiveRemMediaIPAddr,
cvVoIPCallActiveRemMediaPort,
cvVoIPCallHistoryConnectionId,
cvVoIPCallHistoryRoundTripDelay,
cvVoIPCallHistorySelectedQoS,
cvVoIPCallHistorySessionProtocol,
cvVoIPCallHistorySessionTarget,
cvVoIPCallHistoryOnTimeRvPlayout,
cvVoIPCallHistoryGapFillWithSilence,
cvVoIPCallHistoryGapFillWithPrediction,
cvVoIPCallHistoryGapFillWithInterpolation,
cvVoIPCallHistoryGapFillWithRedundancy,
cvVoIPCallHistoryHiWaterPlayoutDelay,
cvVoIPCallHistoryLoWaterPlayoutDelay,
cvVoIPCallHistoryReceiveDelay,
cvVoIPCallHistoryIcpif,
cvVoIPCallHistoryLostPackets,
cvVoIPCallHistoryLatePackets,
cvVoIPCallHistoryEarlyPackets,
cvVoIPCallHistoryUsername,
cvVoIPCallHistoryProtocolCallId,
cvVoIPCallHistoryRemSigIPAddrT,
cvVoIPCallHistoryRemSigIPAddr,
cvVoIPCallHistoryRemSigPort,
cvVoIPCallHistoryRemMediaIPAddrT,
cvVoIPCallHistoryRemMediaIPAddr,
cvVoIPCallHistoryRemMediaPort
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Call
capability."
::= { cvdcMIBGroups 19 }
cvdcNotificationGroupRev1 NOTIFICATION-GROUP
NOTIFICATIONS{
cvdcPoorQoVNotificationRev1
}
STATUS current
DESCRIPTION
"The notifications for the CISCO-VOICE-DIAL-CONTROL-MIB"
::= { cvdcMIBGroups 20 }
cvdcVoIPCfgGroupRev3 OBJECT-GROUP
OBJECTS {
cvVoIPPeerCfgSessionProtocol,
cvVoIPPeerCfgSessionTarget,
cvVoIPPeerCfgCoderRate,
cvVoIPPeerCfgFaxRate,
cvVoIPPeerCfgDesiredQoS,
cvVoIPPeerCfgMinAcceptableQoS,
cvVoIPPeerCfgVADEnable,
cvVoIPPeerCfgExpectFactor,
cvVoIPPeerCfgIcpif,
cvVoIPPeerCfgPoorQoVNotificationEnable,
cvVoIPPeerCfgUDPChecksumEnable,
cvVoIPPeerCfgIPPrecedence,
cvVoIPPeerCfgTechPrefix,
cvVoIPPeerCfgDigitRelay,
cvVoIPPeerCfgCoderBytes,
cvVoIPPeerCfgFaxBytes,
cvVoIPPeerCfgInBandSignaling
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the VoIP Dial Control
configuration capability.
"
::= { cvdcMIBGroups 21 }
cvdcGeneralCfgGroupRev5 OBJECT-GROUP
OBJECTS {
cvGeneralPoorQoVNotificationEnable,
cvPeerCfgIfIndex,
cvPeerCfgType,
cvPeerCfgRowStatus,
cvPeerCfgPeerType,
cvPeerCommonCfgIncomingDnisDigits,
cvPeerCommonCfgMaxConnections,
cvPeerCommonCfgApplicationName,
cvPeerCommonCfgPreference,
cvPeerCommonCfgHuntStop,
cvPeerCommonCfgDnisMappingName,
cvPeerCommonCfgSourceCarrierId,
cvPeerCommonCfgTargetCarrierId,
cvPeerCommonCfgSourceTrunkGrpLabel,
cvPeerCommonCfgTargetTrunkGrpLabel
}
STATUS current
DESCRIPTION
"A collection of objects providing the general
Voice Gateway Call Dial Control configuration
capability."
::= { cvdcMIBGroups 22 }
cvdcVoIPCfgGroupRev4 OBJECT-GROUP
OBJECTS {
cvVoIPPeerCfgSessionProtocol,
cvVoIPPeerCfgSessionTarget,
cvVoIPPeerCfgCoderRate,
cvVoIPPeerCfgFaxRate,
cvVoIPPeerCfgDesiredQoS,
cvVoIPPeerCfgMinAcceptableQoS,
cvVoIPPeerCfgVADEnable,
cvVoIPPeerCfgExpectFactor,
cvVoIPPeerCfgIcpif,
cvVoIPPeerCfgPoorQoVNotificationEnable,
cvVoIPPeerCfgUDPChecksumEnable,
cvVoIPPeerCfgIPPrecedence,
cvVoIPPeerCfgTechPrefix,
cvVoIPPeerCfgDigitRelay,
cvVoIPPeerCfgCoderBytes,
cvVoIPPeerCfgFaxBytes,
cvVoIPPeerCfgInBandSignaling,
cvVoIPPeerCfgMediaSetting,
cvVoIPPeerCfgDesiredQoSVideo,
cvVoIPPeerCfgMinAcceptableQoSVideo,
cvVoIPPeerCfgRedirectip2ip
}
STATUS current
DESCRIPTION
"A collection of objects providing the VoIP Dial Control
configuration capability.
"
::= { cvdcMIBGroups 23 }
cvCallGroupRev3 OBJECT-GROUP
OBJECTS {
cvCallActiveConnectionId,
cvCallActiveTxDuration,
cvCallActiveVoiceTxDuration,
cvCallActiveFaxTxDuration,
cvCallActiveCoderTypeRate,
cvCallActiveNoiseLevel,
cvCallActiveACOMLevel,
cvCallActiveOutSignalLevel,
cvCallActiveInSignalLevel,
cvCallActiveERLLevel,
cvCallActiveSessionTarget,
cvCallActiveImgPageCount,
cvCallActiveCallingName,
cvCallActiveCallerIDBlock,
cvCallActiveEcanReflectorLocation,
cvCallActiveAccountCode,
cvCallHistoryConnectionId,
cvCallHistoryTxDuration,
cvCallHistoryVoiceTxDuration,
cvCallHistoryFaxTxDuration,
cvCallHistoryCoderTypeRate,
cvCallHistoryNoiseLevel,
cvCallHistoryACOMLevel,
cvCallHistorySessionTarget,
cvCallHistoryImgPageCount,
cvCallHistoryCallingName,
cvCallHistoryCallerIDBlock,
cvCallHistoryAccountCode,
cvCallActiveERLLevelRev1
}
STATUS deprecated DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Dial Control configuration
capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 24 }
cvCallGroupRev4 OBJECT-GROUP
OBJECTS {
cvCallActiveConnectionId,
cvCallActiveTxDuration,
cvCallActiveVoiceTxDuration,
cvCallActiveFaxTxDuration,
cvCallActiveCoderTypeRate,
cvCallActiveNoiseLevel,
cvCallActiveACOMLevel,
cvCallActiveOutSignalLevel,
cvCallActiveInSignalLevel,
cvCallActiveSessionTarget,
cvCallActiveImgPageCount,
cvCallActiveCallingName,
cvCallActiveCallerIDBlock,
cvCallActiveEcanReflectorLocation,
cvCallActiveAccountCode,
cvCallHistoryConnectionId,
cvCallHistoryTxDuration,
cvCallHistoryVoiceTxDuration,
cvCallHistoryFaxTxDuration,
cvCallHistoryCoderTypeRate,
cvCallHistoryNoiseLevel,
cvCallHistoryACOMLevel,
cvCallHistorySessionTarget,
cvCallHistoryImgPageCount,
cvCallHistoryCallingName,
cvCallHistoryCallerIDBlock,
cvCallHistoryAccountCode,
cvCallActiveERLLevelRev1
}
STATUS current
DESCRIPTION
"A collection of objects providing the GSTN (General
Switched Telephony Network Voice Dial Control configuration
capability.
GSTN (General Switched Telephony Network), which is
supposed to encompass analog, ISDN, Cellular - essentially
anything circuit switched over the TDM infrastructure.
"
::= { cvdcMIBGroups 25 }
cvVoIPCallGroupRev5 OBJECT-GROUP
OBJECTS {
cvVoIPCallActiveConnectionId,
cvVoIPCallActiveRoundTripDelay,
cvVoIPCallActiveSelectedQoS,
cvVoIPCallActiveSessionProtocol,
cvVoIPCallActiveSessionTarget,
cvVoIPCallActiveOnTimeRvPlayout,
cvVoIPCallActiveGapFillWithSilence,
cvVoIPCallActiveGapFillWithPrediction,
cvVoIPCallActiveGapFillWithInterpolation,
cvVoIPCallActiveGapFillWithRedundancy,
cvVoIPCallActiveHiWaterPlayoutDelay,
cvVoIPCallActiveLoWaterPlayoutDelay,
cvVoIPCallActiveReceiveDelay,
cvVoIPCallActiveLostPackets,
cvVoIPCallActiveLatePackets,
cvVoIPCallActiveEarlyPackets,
cvVoIPCallActiveUsername,
cvVoIPCallActiveProtocolCallId,
cvVoIPCallActiveRemSigIPAddrT,
cvVoIPCallActiveRemSigIPAddr,
cvVoIPCallActiveRemSigPort,
cvVoIPCallActiveRemMediaIPAddrT,
cvVoIPCallActiveRemMediaIPAddr,
cvVoIPCallActiveRemMediaPort,
cvVoIPCallActiveSRTPEnable,
cvVoIPCallHistoryConnectionId,
cvVoIPCallHistoryRoundTripDelay,
cvVoIPCallHistorySelectedQoS,
cvVoIPCallHistorySessionProtocol,
cvVoIPCallHistorySessionTarget,
cvVoIPCallHistoryOnTimeRvPlayout,
cvVoIPCallHistoryGapFillWithSilence,
cvVoIPCallHistoryGapFillWithPrediction,
cvVoIPCallHistoryGapFillWithInterpolation,
cvVoIPCallHistoryGapFillWithRedundancy,
cvVoIPCallHistoryHiWaterPlayoutDelay,
cvVoIPCallHistoryLoWaterPlayoutDelay,
cvVoIPCallHistoryReceiveDelay,
cvVoIPCallHistoryIcpif,
cvVoIPCallHistoryLostPackets,
cvVoIPCallHistoryLatePackets,
cvVoIPCallHistoryEarlyPackets,
cvVoIPCallHistoryUsername,
cvVoIPCallHistoryProtocolCallId,
cvVoIPCallHistoryRemSigIPAddrT,
cvVoIPCallHistoryRemSigIPAddr,
cvVoIPCallHistoryRemSigPort,
cvVoIPCallHistoryRemMediaIPAddrT,
cvVoIPCallHistoryRemMediaIPAddr,
cvVoIPCallHistoryRemMediaPort,
cvVoIPCallHistorySRTPEnable
}
STATUS current
DESCRIPTION
"A collection of objects providing the VoIP Call
capability."
::= { cvdcMIBGroups 26 }
END