| Scalar Object |
| cssSystemLinkTraps | .1.3.6.1.4.1.9.10.44.1.1.1 |
Indicates whether the stack is permitted to generate
linkUp/linkDown traps for both repeater port and
switch module's port. The stack provides only
a single global control of link traps in contrast
to per interface control provided by IF-MIB. The
value of all instances ifLinkUpDownTrapEnable is set
to TRUE (FALSE) if this object is set to enabled
(disabled). The object ifLinkUpDownTrapEnable is
read-only.
A linkUp/linkDown trap is generated whenever a port's
link STATUS or administrative status changes. |
| cssGroupEntry | .1.3.6.1.4.1.9.10.44.1.2.1.1 |
Configuration parameters for an individual hub.
An entry is created by default for the master unit
in the stack. A entry is created (removed) when
a hub is connected to (removed from) the stack. |
| cssRepeaterPortEntry | .1.3.6.1.4.1.9.10.44.1.3.1.1 |
Configuration parameters for an individual repeater
port on a hub. The value of rptrPortIndex also
indicates the physical port number of the port in
the hub. An entry is created for each repeater port in
a hub when the hub is connected to the stack. The
corresponding entries are removed when the hub is
removed from the stack. |
| cssSwitchPortEntry | .1.3.6.1.4.1.9.10.44.1.4.1.1 |
Configuration parameters for an individual switch
module port. An entry is created for each switch port
on a module is inserted into a hub in the stack.
The corresponding entries are removed when the module
is removed from the hub in the stack, or if the hub
is removed from the stack. |
| Tabular Object |
| cssGroupID | .1.3.6.1.4.1.9.10.44.1.2.1.1.1 |
The hub identifier of unit in a stack. |
| cssGroupType | .1.3.6.1.4.1.9.10.44.1.2.1.1.2 |
The model type of the hub unit |
| cssGroupSerialNo | .1.3.6.1.4.1.9.10.44.1.2.1.1.4 |
Serial number of the hardware. |
| cssGroupBoardRevision | .1.3.6.1.4.1.9.10.44.1.2.1.1.5 |
Hardware version of the repeater board. |
| cssGroupAgentBootVersion | .1.3.6.1.4.1.9.10.44.1.2.1.1.6 |
Returns the version number of the dual-speed hub
BOOT software residing in flash. The format is 'V1.2.3'. |
| cssGroupAgentFirmwareVersion | .1.3.6.1.4.1.9.10.44.1.2.1.1.7 |
Returns the version number of the dual-speed hub
firmware residing in flash. The format is 'V1.2.3'. |
| cssGroupAgentStatus | .1.3.6.1.4.1.9.10.44.1.2.1.1.8 |
Status of this hub agent. Each stack allows only
one SNMP primary agent.
notPresent(1): The hub does not have an agent.
primary(2): The agent of this hub is a primary agent.
backup(3) : The agent of this hub is a backup agent. |
| cssGroupAgentPhysAddress | .1.3.6.1.4.1.9.10.44.1.2.1.1.9 |
MAC address of this hub's agent |
| cssGroupInternalPowerState | .1.3.6.1.4.1.9.10.44.1.2.1.1.12 |
Indicates the state of the internal power supply.
off : The internal power supply is off.
on : The internal power supply is on. |
| cssGroupRedundantPowerState | .1.3.6.1.4.1.9.10.44.1.2.1.1.13 |
Indicates the state of the external/backup power
supply.
off : the switch is not connected to a redundant
power source.
healthy : a redundant power source is connected to
the switch and the power source is
operating correctly.
faulty : a redundant power source is connected to
the switch but a failure exists in the
power system. |
| cssGroupReset | .1.3.6.1.4.1.9.10.44.1.2.1.1.14 |
Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not run
the POST (Power On Self Test).
Setting this object to noReset(1) has no effect.
The switch always returns the value noReset(1) when
this object is read. |
| cssGroupConfigDefaultReset | .1.3.6.1.4.1.9.10.44.1.2.1.1.15 |
Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not
run the POST (Power On Self Test). All
configuration parameters will revert to their
factory default settings.
Setting this object to noReset(1) has no effect.
The switch always returns the value noReset(1) when
this object is read. |
| cssGroupIsolatedState | .1.3.6.1.4.1.9.10.44.1.2.1.1.16 |
Setting this object to isolated(1) causes this hub
to be isolated from the back plane bus. Setting
this object to attached(2) causes this hub to be
attached to the back plane bus. |
| cssRepeaterPortName | .1.3.6.1.4.1.9.10.44.1.3.1.1.1 |
A descriptive string of up to 20 characters used
by the network administrator to name a port. |
| cssRepeaterPortControllerRevision | .1.3.6.1.4.1.9.10.44.1.3.1.1.2 |
Returns the revision number of the port controller. |
| cssRepeaterPortSpeedAdmin | .1.3.6.1.4.1.9.10.44.1.3.1.1.3 |
Set to tenMbps(1) to operate in 10Mbps speed mode.
Set to oneHundredMbps(2) to operate in 100Mbps speed
mode. Set to autoNegotiate(3) to allow the switch
to negotiate with the other end of the connection.
The actual operating speed of the port is given by
cssRepeaterPortSpeedStatus. |
| cssRepeaterPortSpeedStatus | .1.3.6.1.4.1.9.10.44.1.3.1.1.4 |
The operating speed of the port. |
| cssRepeaterPortLinkStatus | .1.3.6.1.4.1.9.10.44.1.3.1.1.5 |
The current port link status. |
| cssSwitchPortModuleID | .1.3.6.1.4.1.9.10.44.1.4.1.1.1 |
Unique ID number of a module unit in a hub as used
in the command line interface. |
| cssSwitchPortPortID | .1.3.6.1.4.1.9.10.44.1.4.1.1.2 |
The unique ID identifying a port on an extension module
on a hub as used in the command line interface. |
| cssSwitchPortName | .1.3.6.1.4.1.9.10.44.1.4.1.1.3 |
A descriptive string of up to 20 characters used by the
network administrator to name a switch port. |
| cssSwitchPortType | .1.3.6.1.4.1.9.10.44.1.4.1.1.4 |
Type of switch module in this hub. |
| cssSwitchPortControllerRevision | .1.3.6.1.4.1.9.10.44.1.4.1.1.5 |
The revision number of the port controller. |
| cssSwitchPortState | .1.3.6.1.4.1.9.10.44.1.4.1.1.6 |
Setting this object to enabled(1) enables the port.
Setting this object to disabled(2) disables the port. |
| cssSwitchPortDuplexAdmin | .1.3.6.1.4.1.9.10.44.1.4.1.1.7 |
Set to fullDuplex(1) to operate in full duplex mode: port
will allow simultaneous transmit and receive which can
double its bandwidth. Set to halfDuplex(2) to operate in
normal mode. Set to autoNegotiate(3) to allow the switch
to negotiate the duplex status with the other end of the
connection. |
| cssSwitchPortDuplexStatus | .1.3.6.1.4.1.9.10.44.1.4.1.1.8 |
The operating duplex mode of the switched port. |
| cssSwitchPortSpeedAdmin | .1.3.6.1.4.1.9.10.44.1.4.1.1.9 |
Set to tenMbps(1) to operate in 10Mbps speed mode. Set to
oneHundredMbps(2) to operate in 100Mbps speed mode. Set to
autoNegotiate(3) to allow the switch to negotiate the operating
speed with the other end of the connection.
If the value of object cssSwitchPortType is WS-X4002(2),
this object will be read-only, because FX module only
supports 100Mbps speed. |
| cssSwitchPortSpeedStatus | .1.3.6.1.4.1.9.10.44.1.4.1.1.10 |
The operating speed of the switched port. |
| cssSwitchPortLinkStatus | .1.3.6.1.4.1.9.10.44.1.4.1.1.11 |
Indicates the link STATUS of switch port. |
| Table |
| cssGroupTable | .1.3.6.1.4.1.9.10.44.1.2.1 |
A list of member hubs in the stack. |
| cssRepeaterPortTable | .1.3.6.1.4.1.9.10.44.1.3.1 |
The list of repeater port configurations on each hub
unit. |
| cssSwitchPortTable | .1.3.6.1.4.1.9.10.44.1.4.1 |
A list of switched ports on extension module on a each
hub unit in the stack. |
| Trap |
| ciscoSibuStackableDualSpeedHubRptrPortLinkChange | .1.3.6.1.4.1.9.10.44.2.0.1 |
This trap is generated whenever the value of
cssRepeaterPortLinkStatus changes for a repeater port. |
| ciscoSibuStackableDualSpeedHubSwitchPortLinkChange | .1.3.6.1.4.1.9.10.44.2.0.2 |
This trap is generated whenever the value of
cssSwitchPortLinkStatus changes for a switch port
on an extension module. |
| Object Identifier |
| ciscoSibuStackableDualSpeedHubMIB | .1.3.6.1.4.1.9.10.44 |
The MIB module that extends the REPEATER-MIB to
manage CISCO low end stackable repeater products.
For the purpose of this mib, a hub is a repeater
group and stack is collection of one or more hubs
interconnected via stack bus connectors. |
| ciscoSibuStackableDualSpeedHubMIBObjects | .1.3.6.1.4.1.9.10.44.1 |
| cssSystem | .1.3.6.1.4.1.9.10.44.1.1 |
| cssGroup | .1.3.6.1.4.1.9.10.44.1.2 |
| cssRepeaterPort | .1.3.6.1.4.1.9.10.44.1.3 |
| cssSwitchPort | .1.3.6.1.4.1.9.10.44.1.4 |
| ciscoSibuStackableDualSpeedHubNotifications | .1.3.6.1.4.1.9.10.44.2 |
| ciscoSibuStackableDualSpeedHubNotificationsPrefix | .1.3.6.1.4.1.9.10.44.2.0 |
| ciscoSibuStackableDualSpeedHubMIBComformance | .1.3.6.1.4.1.9.10.44.3 |
| ciscoSibuStackableDualSpeedHubMIBCompliances | .1.3.6.1.4.1.9.10.44.3.1 |
| ciscoSibuStackableDualSpeedHubMIBGroups | .1.3.6.1.4.1.9.10.44.3.2 |
| Group |
| ciscoSibuStackableDualSpeedHubGroup | .1.3.6.1.4.1.9.10.44.3.2.1 |
A collection of group objects for use with the Cisco
Stackable Dual-Speed Hub products. |
| ciscoSibuStackableDualSpeedHubRepeaterPortGroup | .1.3.6.1.4.1.9.10.44.3.2.2 |
A collection of repeater port objects for use
with the Cisco Stackable Dual-Speed Hub products. |
| ciscoSibuStackableDualSpeedHubSwitchPortGroup | .1.3.6.1.4.1.9.10.44.3.2.3 |
A collection of switch module port objects for use with
the Cisco Stackable Dual-Speed Hub products. |